to “Sealing a Tire with TIREFIT”
section (F) “Sealant Bottle and
Hose Replacement”.
The Sealant Bottle (1) and Sealant Hose (6) are a one tire application
use. After each use, always replace
these components immediately at
an authorized dealer.
When the TIREFIT sealant is in a liquid form, clean water, and a
damp cloth will remove the mate-
rial from the vehicle or tire and
wheel components. Once the seal-
ant dries, it can easily be peeled off
and properly discarded.
For optimum performance, make sure the valve stem on the wheel is
free of debris before connecting the
TIREFIT kit.
You can use the TIREFIT air pump to inflate bicycle tires. The kit also
comes with two needles, located in
the Accessory Storage Compart-
ment (on the bottom of the air
pump) for inflating sport balls,
rafts, or similar inflatable items.
However, use only the Air Pump Hose (7) and make sure the Mode
Select Knob (5) is in the Air Mode
when inflating such items to avoid
injecting sealant into them. The
TIREFIT Sealant is only intended
to seal punctures less than 6 mm
diameter in the tread of your
vehicle.
Do not lift or carry the TIREFIT kit by the hoses.
WARNING!
Do not attempt to seal a tire onthe side of the vehicle close to
traffic. Pull far enough off the
road to avoid the danger of being
hit when using the TIREFIT kit.
Do not use TIREFIT or drive the vehicle under the following cir-
cumstances:– If the puncture in the tire tread is approximately 6 mm or
larger.
– If the tire has any sidewall damage.
(Continued)
WARNING!(Continued)
If the tire has any damage fromdriving with extremely low tire
pressure.
If the tire has any damage from driving on a flat tire.
If the wheel has any damage.
If you are unsure of the condition of the tire or the wheel.
Keep TIREFIT away from open flame or heat source.
A loose TIREFIT kit thrown for- ward in a collision or hard stop
could endanger the occupants of
the vehicle. Always stow the
TIREFIT kit in the place pro-
vided. Failure to follow these
warnings can result in injuries
that are serious or fatal to you,
your passengers, and others
around you.
(Continued)
255
7
MAINTAINING YOUR VEHICLE
ENGINE COMPARTMENT — 3.6L............269
ENGINE COMPARTMENT — 3.0L DIESEL .....270
ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .271
REPLACEMENT PARTS ...................271
MAINTENANCE PROCEDURES ..............271
ENGINE OIL – GASOLINE ENGINE .........272
ENGINE OIL – DIESEL ENGINE ...........273
SYNTHETIC ENGINE OILS ...............273
MATERIALS ADDED TO ENGINE OILS ......273
DISPOSING OF USED ENGINE OIL AND FILTERS .............................273
ENGINE OIL FILTER ....................273
ENGINE AIR CLEANER FILTER ...........274
MAINTENANCE-FREE BATTERY ..........274
AIR CONDITIONER MAINTENANCE ........275
A/CAIRFILTER .......................276
BODY LUBRICATION ...................276
WINDSHIELD WIPER BLADES ...........277
ADDING WASHER FLUID ................277
INTERVENTION REGENERATION STRATEGY – 3.0L DIESEL ENGINE ...................278
EXHAUST SYSTEM .....................278
267
CAUTION!
It is essential when replacing thecables on the battery that the
positive cable is attached to the
positive post and the negative
cable is attached to the negative
post. Battery posts are marked
positive (+) and negative (-) and
are identified on the battery case.
Cable clamps should be tight on
the terminal posts and free of cor-
rosion.
If a “fast charger” is used while the battery is in the vehicle, dis-
connect both vehicle battery
cables before connecting the
charger to the battery. Do not use
a “fast charger” to provide start-
ing voltage.
AIR CONDITIONER
MAINTENANCE
For best possible performance, your
air conditioner should be checked and
serviced by an authorized dealer at
the start of each warm season. This
service should include cleaning of the condenser fins and a performance
test. Drive belt tension should also be
checked at this time.
CAUTION!
Do not use chemical flushes in your
air conditioning system as the
chemicals can damage your air
conditioning components. Such
damage is not covered by the New
Vehicle Limited Warranty.
WARNING!
Use only refrigerants and com-
pressor lubricants approved by
the manufacturer for your air
conditioning system. Some unap-
proved refrigerants are flam-
mable and can explode, injuring
you. Other unapproved refriger-
ants or lubricants can cause the
system to fail, requiring costly re-
pairs.
(Continued)
WARNING!(Continued)
The air conditioning system con-tains refrigerant under high pres-
sure. To avoid risk of personal
injury or damage to the system,
adding refrigerant or any repair
requiring lines to be disconnected
should be done by an experienced
technician.
Refrigerant Recovery And
Recycling
R-134a Air Conditioning Refrigerant
is a hydrofluorocarbon (HFC) that is
endorsed by the Environmental Pro-
tection Agency and is an ozone-saving
product. However, the manufacturer
recommends that air conditioning
service be performed by authorized
dealer or other service facilities using
recovery and recycling equipment.
NOTE: Use only manufacturer
approved A/C system PAG com-
pressor oil and refrigerants.
275
Keep the front of the radiator clean.If your vehicle is equipped with air
conditioning, keep the front of the
condenser clean.
Do not change the thermostat for Summer or Winter operation. If re-
placement is ever necessary, install
ONLY the correct type thermostat.
Other designs may result in unsat-
isfactory engine coolant (anti-
freeze) performance, poor gas mile-
age, and increased emissions.
BRAKE SYSTEM
In order to assure brake system per-
formance, all brake system compo-
nents should be inspected periodi-
cally. Refer to the “Maintenance
Schedule” for the proper maintenance
intervals.
WARNING!
Riding the brakes can lead to brake
failure and possibly an accident.
Driving with your foot resting or
riding on the brake pedal can result
in abnormally high brake tempera-
tures, excessive lining wear, and
possible brake damage. You would
not have your full braking capacity
in an emergency.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience. Master Cylinder – Brake Fluid
Level Check
Check the fluid level in the master
cylinder immediately if the brake sys-
tem warning light indicates system
failure.
Check the fluid level in the master
cylinder when performing underhood
services.
Clean the top of the master cylinder
area before removing the cap. Add
fluid to bring the level up to the
“MAX” mark on the side of the master
cylinder reservoir.
Add enough fluid to bring the level up
to the requirements described on the
brake fluid reservoir. With disc
brakes, fluid level can be expected to
fall as the brake pads wear. However,
low fluid level may be caused by a
leak and a checkup may be needed.
Use only manufacturer's recom-
mended brake fluid. Refer to “Fluids,
Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for fur-
ther information.
283
CAUTION!
Using a transmission fluid other
than the manufacturer’s recom-
mended fluid may cause deteriora-
tion in transmission shift quality
and/or torque converter shudder,
and will require more frequent fluid
and filter changes. Refer to “Fluids,
Lubricants, and Genuine Parts” in
this section for fluid specifications.
Special Additives
The manufacturer strongly recom-
mends against using any special addi-
tives in the transmission.
Automatic Transmission Fluid (ATF)
is an engineered product and its per-
formance may be impaired by supple-
mental additives. Therefore, do not
add any fluid additives to the trans-
mission. The only exception to this
policy is the use of special dyes for
diagnosing fluid leaks. Avoid using
transmission sealers as they may ad-
versely affect seals.
CAUTION!
Do not use chemical flushes in your
transmission as the chemicals can
damage your transmission compo-
nents. Such damage is not covered
by the New Vehicle Limited War-
ranty.
Fluid Level Check
The fluid level is preset at the factory
and does not require adjustment un-
der normal operating conditions.
Routine fluid level checks are not re-
quired, therefore the transmission has
no dipstick. Your authorized dealer
can check your transmission fluid
level using special service tools.
If you notice fluid leakage or trans-
mission malfunction, visit your au-
thorized dealer immediately to have
the transmission fluid level checked.
Operating the vehicle with an im-
proper fluid level can cause severe
transmission damage.
CAUTION!
If a transmission fluid leak occurs,
visit your authorized dealer imme-
diately. Severe transmission dam-
age may occur. Your authorized
dealer has the proper tools to adjust
the fluid level accurately.
Fluid And Filter Changes –
5-Speed Transmission
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
In addition, change the fluid and filter
if the fluid becomes contaminated
(with water, etc.) or if the transmis-
sion is disassembled for any reason.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
285
Fluid And Filter Changes –
8-Speed Transmission
Under normal operating conditions,
the fluid installed at the factory will
provide satisfactory lubrication for
the life of the vehicle. Routine fluid
and filter changes are not required.
However, change the fluid and filter if
the fluid becomes contaminated (with
water, etc.), or if the transmission is
disassembled for any reason.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
ALL WHEEL DRIVE (AWD)
(for versions/markets,
where provided)
The all wheel drive system consists of
a transfer case and front differential.The exterior surface of these compo-
nents should be inspected for evi-
dence of fluid leaks. Confirmed leaks
should be repaired as soon as possible.
The transfer case fluid fill/inspection
plug is located in the middle of the
rear housing. To inspect the transfer
case fluid level, remove the fill/
inspection plug. The fluid level should
be even with the bottom of the hole.
Use this plug to add fluid as required.
The front differential fill plug is lo-
cated on the outer cover near the half-
shaft attachment. To inspect the dif-
ferential fluid level, remove the fill
plug. The fluid level should be even
with or slightly below the bottom of
the hole.
REAR AXLE
For normal service, periodic fluid
level checks are not required. When
the vehicle is serviced for other rea-
sons the exterior surfaces of the axle
assembly should be inspected. If gear
oil leakage is suspected inspect the
fluid level. Refer to “Fluids, Lubri-
cants, and Genuine Parts” in “Main-
taining Your Vehicle” for further in-
formation.
Fluid Level Check
Check the fluid level by removing the
fill plug on the axle. The fluid level
should be at the bottom of the fill
hole. Add fluid, if necessary, to main-
tain the proper level. Refer to “Fluids,
Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for fur-
ther information.
Change Axle Fluid
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
APPEARANCE CARE AND
PROTECTION FROM
CORROSION
Protection Of Body And Paint
From Corrosion
Vehicle body care requirements vary
according to geographic locations and
usage. Chemicals that are sprayed on
trees and road surfaces during other
seasons, are highly corrosive to the
286
metal in your vehicle. Outside park-
ing, which exposes your vehicle to air-
borne contaminants, road surfaces on
which the vehicle is operated, extreme
hot or cold weather and other extreme
conditions will have an adverse effect
on paint, metal trim, and underbody
protection.
The following maintenance recom-
mendations will enable you to obtain
maximum benefit from the corrosion
resistance built into your vehicle.
What Causes Corrosion?
Corrosion is the result of deterioration
or removal of paint and protective
coatings from your vehicle.
The most common causes are:
Road salt, dirt and moisture accu-mulation.
Stone and gravel impact.
Insects, tree sap and tar.
Salt in the air near seacoast localities.
Atmospheric fallout/industrial pol- lutants. Washing
Wash your vehicle regularly. Al-
ways wash your vehicle in the shade
using a mild car wash soap, and
rinse the panels completely with
clear water.
Use a high quality cleaner wax to protect your paint finish. Take care
never to scratch the paint.
Avoid using abrasive compounds and
power buffing that may diminish the
gloss or thin out the paint finish.
CAUTION!
Do not use abrasive or strong clean-
ing materials such as steel wool or
scouring powder that will scratch
metal and painted surfaces.
Special Care
If you drive on salted or dusty roads or if you drive near the ocean, hose
off the undercarriage at least once a
month. It is important that the drain holes
in the lower edges of the doors,
rocker panels, and cargo area be
kept clear and open.
If you detect any stone chips or scratches in the paint, touch them
up immediately. The cost of such
repairs is considered the responsi-
bility of the owner.
If your vehicle is damaged due to an accident or similar cause, which de-
stroys the paint and protective
coating, have your vehicle repaired
as soon as possible. The cost of such
repairs is considered the responsi-
bility of the owner.
If you carry special cargo such as chemicals, fertilizers, de-icer salt,
etc., be sure that such materials are
well packaged and sealed.
If a lot of driving is done on gravel roads, consider mud or stone
shields behind each wheel.
Use Touch Up Paint or equivalent on scratches as soon as possible.
287
Cavity Cartridge Fuse Mini-Fuse Description
11 — 20 Amp Yellow Horns
12 — 10 Amp Red Air Conditioning Clutch
13 — — Spare
14 — — Spare
15 — — Spare
16 — — Spare
18 50 Amp Red — Radiator Fan #2
19 50 Amp Red — Power Steering #2
20 30 Amp Pink — Wiper Motor
21 30 Amp Pink — Headlamp Washers
22 50 Amp Red — Glow Plug Module — Diesel Only
23 30 Amp Pink — Fuel Pump Feed/Diesel Fuel Heater — Diesel Only
24 50 Amp Red — Cabin Heater #3 — Diesel Only
28 — 25 Amp Natural Fuel Pump
29 — 15 Amp Blue Transmission/Shifter (TCM Module)
30 — — Spare
31 — 25 Amp Natural Engine Module (PCM)
32 — — Spare
33 — — Spare
34 — 25 Amp Natural ASD Feed #1
35 — 20 Amp Yellow ASD Feed #2
36 — 10 Amp Red Anti-Lock Brake Module (ABS/ESP Module)
37 — 10 Amp Red Engine Controller (PCM)/Rad Fan Relay Coils
38 — 10 Amp Red Airbag Module291