2014 INFINITI QX60 brake

8
essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low – Add Air warning message
will appear in the vehicle information display
01
and the low tire pressure warning light 02 will
illuminate when one or more tires are low on
pressure and air is needed.
•
The tire pressures should be checked when the


tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more
or driven less than 1 mi (1.6 km) at
moderate speeds.
When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tires to the
recommended COLD tire pressure.
To use the tire inflation indicator:
1.


Move the shift lever to the
P (PARK) position and apply the parking brake.
2.


Place the ignition switch in the
ON position. Do not start the engine.
3.


Add air to the under-inflated tire and within a few seconds, the hazard \
warning lights will
start flashing.
4.


When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5.


Repeat this procedure for any additional under-inflated tires.
After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h).
The Tire Pressure Low – Add Air warning message and low tire pressure warning light
will disappear.
When the low tire pressure warning light flashes for approximately 1 min\
ute and then
remains on, the TPMS is not functioning properly. Have the system checke\
d by an
INFINITI retailer.
Tire pressure rises and falls depending on the heat caused by the vehicl\
e’s operation and
the outside temperature. Low outside temperature can lower the temperatu\
re of the air
inside the tire, which can cause a lower tire inflation pressure. This m\
ay cause the low
tire pressure warning light to illuminate. If the warning light illumina\
tes, check the tire
pressure in your tires.
•
Check

the tire pressure (including the spare tire) often and always prior to long

distance trips.
The Tire and Loading Information label contains valuable information. Pl\
ea se refer to
section 9, “Technical and consumer information” in your Owner’s\
Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
01
02
1591599_14b_Infiniti_QX60_QRG_100913.indd 810/9/13 11:09 AM

11
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)
The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.
The remote engine start operating range is approximately 200 ft (60 m)\

from the vehicle. The effective operating range may be shorter due to
environmental conditions or obstacles between you and the vehicle.
For the remote engine start to function, the vehicle must be in
the P (PARK) position with the ignition off, and all the doors closed
and locked.
To start your vehicle remotely:



1.

Press the button
01
2. Within 5 seconds press and hold the remote engine start
button
02 for at least
2 seconds.
The engine will start and the parking lights will turn on.
Automatic climate control will begin heating or cooling the vehicle depe\
nding on the last
used mode.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.

•
After
two remote starts the ignition switch must be cycled before the remote start can be
used again.
To start driving depress the brake pedal and push the ignition switch START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE
The lock and unlock operating range of the
Intelligent Key is within 31.5 in (80 cm) from
each request switch.
To lock the vehicle, push either door handle



request switch 03 once or press the
button
01
on the key fob.
To unlock the vehicle, perform one of the following procedures:

•
Push
either door handle request switch
03 once; the corresponding door will unlock.
Push the door handle request switch again
within 30 seconds; all other doors
will unlock, or
• Press

the
button
04 on the key fob to unlock the driver’s side door. Press the



button

again;

all

other

doors

will

unlock.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
02
01
04
05
06
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 1110/9/13 11:09 AM

LIFTGATE RELEASE
To open the rear liftgate, press the button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM
The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights \
will stay on for a period of time.
INTELLIGENT KE
y
BATTER y DISCHARGE
If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1.


Move the shift lever to the
P (P ARK ) position.



2.

Firmly apply the foot brake.




3.

Touch the ignition switch with
the Intelligent
Key and a chime will sound.



4.

Within 10 seconds after the chime sounds, push the ignition switch while\
depressing
the

brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
12
first drive features
Power Liftgate
When the liftgate is closed and locked, the
liftgate will open automatically by:

•
Pushing the power liftgate switch
01 on the instrument panel.
•
Pushing the liftgate opener switch 02, the
liftgate must be unlocked, or you must have the
Intelligent Key with you (in your pocket or purse).
•


Pressing the
button
03 on the INFINITI
Intelligent Key for more than 1 second.
The power liftgate operation can be
turned on or off by the power liftgate main
switch
04 on the instrument panel.


•
When the power liftgate main switch is pushed

to the OFF position, power operation is not
available using the power liftgate switch on the
liftgate
05 or the liftgate opener switch
02.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
0401
02
05
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 1210/9/13 11:09 AM

15
REVERSE TILT-DOWN FEATURE (if so equipped)
The
reverse tilt-down feature will turn the selected outside mirror surface\
downward to
provide better rear visibility close to the vehicle.



1.

Apply the brake.




2.

Push the ignition switch to the
ON position.



3.

Move the shift lever to the
R (REVERSE) position.



4.

Choose the right or left outside mirror by operating the outside mirror \
control switch 01.



5.


The outside mirror surfaces move downward.


The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:

• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) posit\
ion.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Engine
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch
START/STOP button to
start the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position and
apply the parking brake.
Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1591599_14b_Infiniti_QX60_QRG_100913.indd 1510/9/13 11:09 AM

21
USB/iPod® Interface
The USB jack 01 is located in the center console
under the arm rest.
When a compatible USB memory device or
iPod® is plugged into the USB jack, compatible
audio and video files stored on the device can
be played through the vehicle’s audio system
and front display.
For more information, refer to the “Monitor, climate, audio, phone and
voice recognition systems (section 4)” of your Owner’s Manual.
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 MPH (40 km/h).
The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.
To activate the cruise control, push the CRUISE

ON/OFF

switch
01. The
CRUISE
indicator light in



the instrument panel will illuminate.
To set cruising speed, accelerate the vehicle to the
desired speed, push the COAST/SET switch
02
and release. The SET indicator light
in the instrument panel will illuminate. Take your foot
off the accelerator pedal.
y
our vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCEL/RES switch 03. When the



vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET switch 02. Release the



switch when the vehicle slows to the desired speed.
0102
03
04
01
04 STATION PRESET BUTTONS
Twelve stations can be set for the FM band, six for the AM band and eigh\
teen for
satellite radio.
To store a station in a preset, you must first select a radio band by pr\
essing the
FM•AM


05 or XM
06 button, then tune to the desired FM, AM or XM satellite radio station.
Then press and hold the desired station preset button
(1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indic\
ator will then
display and the sound will resume. Programming is now complete.
To retrieve a previously set station, select the radio band where the pr\
eset was stored
then press the corresponding station select button (1-6).
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your
Owner’s Manual.
1591599_14b_Infiniti_QX60_QRG_100913.indd 2110/9/13 11:09 AM

first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,



press the
CRUISE ON/OFF button
01 for less than 1.5
seconds. The
CRUISE indicator light
02 will illuminate.
Accelerate to the desired speed.
Push down on the
COAST/SET switch
03 and release
it. Cruise control will be set to the desired speed.
Press the distance button 04 repeatedly to change
the set distance between long, middle, and short.
Wh en a vehicle is not detected ahead of you in



the lane, the set distance and set vehicle speed




indicator lights will illuminate 05 in set mode.
When a vehicle is detected ahead of you in the lane,



the vehicle ahead detection, set distance, and set



vehicle speed indicator lights will illuminate 06 in set mode.
To reset at a faster cruising speed, push and hold the
ACCEL/RES
switch
07. When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET
switch
03. Release the switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator 05 will go out.
To turn off cruise control, press the
CRUISE ON/OFF button
01. The CRUISE indicator light

02, in the instrument panel, will turn off.
To set conventional (fixed speed) cruise control mode:
While cruise control is off, press the CRUISE ON/OFF
button 01
and hold it down for more
than 1.5 seconds. The
CRUISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.



Cruise control will be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off\
, a nd then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
0403
0708
0205
06
To cancel the preset speed, push the CANCEL switch
04.
To turn off cruise control, push the CRUISE
ON/OFF switch
01. Both the
CRUISE indicator
light
and the

SET indicator light in the instrument panel will turn off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
22
1591599_14b_Infiniti_QX60_QRG_100913.indd 2210/9/13 11:09 AM

31
Theater Package (if so equipped)
With this Entertainment System, you can play video
files via a DVD or CD providing images and sound
both from the front and rear display screens.
y ou can also connect auxiliary devices such as
video games, camcorders or portable video players
to the auxiliary jacks
01 located on the back of the
center console. (
y
our device will be controlled
through its own control panel.)
Rear Auxiliary Mode allows rear seat passengers
to independently display different sources on
each screen.
Use the remote controller 02, provided with the
system, to operate the rear display screens.
Use the headphones 03, also provided with the
system, to listen to audio wirelessly and
independently.
y
ou may also connect your own
wired-headphones to the headphone jacks
04
located on the back of the center console.
For optimum performance, select the appropriate
headphone channel
05 that corresponds to the
headrest display being viewed directly in front of you.
To watch or control videos on the front display make
sure the vehicle is in the P (PARK) position and the
parking brake is applied.
To reduce driver distraction, the wireless headphones will not
operate while located in the front seats and movies will not be
shown on the front display while the vehicle is in any drive position.
To access standard DVD controls on the front display while play ing a
DVD on the rear display, press the DISC•AUX button on the audio
control panel while the vehicle is in the P (PARK) position and the
parking brake is applied.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
09 – Press to switch between the day screen (bright) and the night sc\
reen (dark). Press
and hold the button to turn the display off. Press again to turn the dis\
play on.
10 BACK – Press to return to the previous screen. In a settings screen, this\
button can also
be used to apply the setting. In a character input screen, this button c\
an also delete the
characters that have been entered.
11 VOICE – Press to hear the current voice guidance for a programmed route.
For more information, please refer to your Navigation System Owner’s \
Manual.z
05
04
01
02
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 3110/9/13 11:09 AM