Page 9 of 36

essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low - Add Air warning message will
appear in the vehicle information display
01 and the
low tire pressure warning light 02 will illuminate when
one or more tires are low on pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.
When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and audible signals to hel\
p you inflate the tires
to the recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire and within a few seconds, the hazard \
warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.
After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h).
The Tire Pressure Low - Add Air warning message and low tire pressure warning light
will disappear.
Hybrid Awareness
Your vehicle is virtually silent in the electric mode. If you exit your \
vehicle while it is ON,
but the engine is not running, the engine will automatically start, info\
rming you that the
car is still ON.
Do not store your INFINITI Intelligent Key within detection range of the\
vehicle. This may
cause welcome lights and other functions to activate creating unwanted b\
attery drain.
The hybrid system is designed for optimum efficiency and performance. Ac\
tivation of the
electric mode may vary with driving conditions and driver input. A full \
battery display does
not indicate the vehicle should be in the electric mode.
For more information, refer to the “Hybrid System Overview” section of your Owner’s Manual.
Hybrid System Warning Light
This light will illuminate when the ignition switch is in
the ON position and will turn off when the hybrid
system is started.
The light will also illuminate when a malfunction occurs in the electric\
motor or hybrid system.
When this light illuminates while driving, immediately stop the vehicle \
in a safe location
and contact an INFINITI retailer.
If the hybrid system warning light blinks while driving, it may indicate\
that the Li-ion
battery charge is low and you cannot continue to drive.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
7
02
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 79/24/13 11:43 AM
Page 10 of 36

8
Accessing the Front Cup Holders
To open the cup holders, push the lid 01 down
and release.
For more information, refer to the “Instruments and controls (section 2)” of
your Owner’s Manual.
01
essential information
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear
in the vehicle information display
01 when the
fuel-filler cap is not tightened correctly.
To tighten, turn the cap clockwise until a single
click is heard.
The warning message will disappear when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button
02 is pressed for about 1 second.
If the cap is not properly tightened, the Malfunction Indicator Light
may illuminate.
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
01
02
When the low tire pressure warning light flashes for approximately 1 min\
ute and then remains
on, the TPMS is not functioning properly. Have the system checked by an \
INFINITI retailer.
Tire pressure rises and falls depending on the heat caused by the vehicl\
e’s operation and the
outside temperature. Low outside temperature can lower the temperature o\
f the air inside
the tire, which can cause a lower tire inflation pressure. This may caus\
e the low tire pressure
warning light to illuminate. If the warning light illuminates, check the\
tire pressure in your tires.
• Check the tire pressure (including the spare tire) often and always pr\
ior to long distance trips.
The Tire and Loading Information label contains valuable information. Pl\
ease refer to
section 9, “Technical and consumer information” in your Owner’s\
Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
Front Armrest/Center Console Storage Box
To access the top storage bin, pull up on the driver’s
side lever
01.
To access the bottom storage bin, pull up on the
passenger’s side lever
02.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
0102
Fuel-filler Door
The fuel-filler door is located on the driver’s side of the vehicle.
The fuel-filler door automatically locks/unlocks
when the driver’s door is locked/unlocked.
To open the fuel-filler door, push the right side of
the fuel-filler door and release.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 89/24/13 11:43 AM
Page 11 of 36

Clock Set/Adjustment
DIGITAL CLOCK ADJUSTMENT
To adjust the time and the appearance
of the clock on the display:
1. Press the SETTING button on the control panel.
2.
Touch the Others key.
3.
Touch the Clock key.
The following settings can be adjusted:
•
On-screen Clock: The clock in the upper right corner
of the display can be turned ON or OFF.
• Clock Format (24h): The clock can be set to 12 hours or 24 hours.
• Offset (hour): The time can be adjusted by increasing or decreasing per hour.
•
Offset (min): The time can be adjusted by increasing or decreasing per minute.
• Daylight Savings Time: The application of daylight savings time can be turned ON or OFF.
• Time Zone: Adjust the time zone. Choose a time zone from the available list.
Press the BACK button to return to the previous screen.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your
Owner’s Manual.
9
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 99/24/13 11:43 AM
Page 12 of 36

10
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)
The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.
The remote engine start operating range is approximately 200 ft
(60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.
For the remote engine start to function, the vehicle must be in the
P (PARK) position with the ignition off, and all the doors closed
and locked.
To start your vehicle remotely:
1. Press the
button
01.
2. Within 5 seconds press and hold the remote
engine start
button
02 for at least 2 seconds.
The engine will start and the parking lights will turn on.
Automatic climate control will begin heating or
cooling the vehicle depending on the last used mode.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.
• After two remote starts the ignition switch must be cycled before the re\
mote
start can be
used again.
To start driving depress the brake pedal and push the ignition switch
START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE
The lock and unlock operating range of the Intelligent Key is within 31.\
5 in (80 cm) from
each request switch.
To lock the vehicle, push either door handle request switch
03 once or press the
button
01 on the key fob.
To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch
03 once; the corresponding door will unlock. Push
the door handle request switch again within 30 seconds; all other doors will unlock, or
• Press the
button
04 on the key fob to unlock the driver’s side door. Press the
button again; all other doors will unlock.
LIFTGATE RELEASE
To open the rear liftgate, press the
button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM
The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
first drive features
02
01
04
05
06
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 109/24/13 11:43 AM
Page 13 of 36

INTELLIGENT KEy BATTERy DISCHARGE
If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while depressing
the brake pedal and the engine will start.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
11
Power Liftgate
When the liftgate is closed and locked, the liftgate
will open automatically by:
• Pushing the power liftgate switch
01 on the
instrument panel.
• Pushing the liftgate opener switch
02, the
liftgate must be unlocked, or you must have the
Intelligent Key with you (in your pocket or purse).
• Pressing the
button
03 on the INFINITI
Intelligent Key for more than 1 second.
The power liftgate operation can be turned on or
off by the power liftgate main switch
04 on the
instrument panel.
•
When the power liftgate main
switch is pushed to the OFF
position, power operation is not
available using the power liftgate
switch on the liftgate
05 or the
liftgate opener switch 02.
For more information, refer to the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
0401
02
0503
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 119/24/13 11:43 AM
Page 14 of 36

first drive features
12
Power Seat Adjustments
To slide the seat forward or backward, push the
control switch
01 forward or backward.
To recline the seatback, push the switch
02
forward or backward.
SEAT LIFTER
To raise or lower the front portion or height of the
seat, push the front or back end of the switch
01 up or down.
POWER LUMBAR SUPPORT (if so equipped for driver’s seat)
To adjust the seat lumbar support, push the front or back end of the swi\
tch
03.
For more information, refer to the “Safety —— seats, seat belts and supplemental restraint system (section 1)”\
of your
Owner’s Manual.
2ND Row Seats
To slide the seat forward or backward, pull the
center of the bar
01 up and hold it while you slide
the seat forward or backward to the desired
position. Release the bar to lock the seat
in position.
To recline the seatback, pull up on the recline handle
02 and lean back. To bring the seatback forward, pull
the lever up and lean your body forward. Release the
lever to lock the seatback in position.
MULTI-MODE/CHILD SEAT ACCESS FUNCTION
This feature is not available on driver’s side of 2nd row seat.
If a child safety seat is installed on the passenger’s side of the 2nd row seat, the 3rd row
can be accessed without removing the child safety seat.
To access the 3rd row from outside the vehicle, lift up on the seatback release lever
03.
EZ ENTRy MODE
To enter the 3rd row from outside the vehicle, lift up on fully the seatback lever
03.
This will release the back of the seat and fold up the seat cushion.
For access to the rear seat slide the entire seat forward by pushing on \
the upper
seatback area.
To return the seat to a locked position, push the upper seatback rearwar\
d until the
seatback and track are locked. Push the seat cushion down. Locking the s\
eatback will
also lock the track.
For more information, refer to the “Safety —— seats, seat belts and supplemental restraint system (section 1)”\
of your Owner’s Manual.
010203
0102
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 129/24/13 11:43 AM
Page 15 of 36

13
3RD Row Manual Reclining Seatback
To recline the seatback, pull up on the latch
01
located on the outside corner of each seatback.
Lean back until the desired angle is obtained.
To bring the seatback forward again, pull up on the
latch
01 and move your body forward. The
seatback will move forward.
For more information, refer to the “Safety —— seats, seat belts and
supplemental restraint system (section 1)” of your Owner’s Manual.
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
01 memory.
Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
•
Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the
adjusting switches for each feature.
• Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second.
• The indicator light on the memory switch you select will illuminate for \
approximately
5 seconds, and a chime will sound (if so equipped) when memory is stor\
ed correctly.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to your preference.
These memorized positions can also be linked to your INFINITI Intelligen\
t Key.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch
01 right or left.
Adjust each mirror to the desired position using the
switch
02.
To fold the outside rearview mirrors, push the
switch
03 to the
position. To unfold the
outside rearview mirrors, push the switch
03 to
the
position.
02
01
03
01
01
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 139/24/13 11:43 AM
Page 16 of 36

first drive features
14REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn the selected outside mirror surf\
ace downward to
provide better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Choose the right or left outside mirror by operating the outside mirror \
control switch
01.
3. Move the shift lever to the R (REVERSE) position.
4. The outside mirror surfaces move downward.
The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) posit\
ion.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Hybrid System
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP button to
start the hybrid system.
TURNING THE HYBRID SYSTEM OFF
Move the shift lever to the P (PARK) position and
apply the parking brake.
Press the ignition switch START/STOP button to turn the hybrid system off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Assist Charge Gauge
This shows the power consumed 02, or generated
01 by the electric motor.
For more information, refer to the “Hybrid System Overview” section and the
“Instruments and controls (section 2)” of your Owner’s Manual.0102
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 149/24/13 11:43 AM