2014 FIAT PUNTO spare wheel

135
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
CHANGING A TYRE GENERAL INSTRUCTIONS
Wheel changing and correct use of the
jack and spare wheel call for some pre-
cautions, as listed below.
Use your hazard lights,
warning triangle, etc to show
that your car is stationary. Passengers
should get out of the car, particular-
ly if it is heavily loaded, and wait for
the wheel to be changed away from
the traffic. Apply the handbrake.
WARNING
The spare wheel provided is
specific for your vehicle.
Therefore, it must not be used on dif-
ferent models and you should not use
spare wheels from other models on
your vehicle. The wheel bolts are spe-
cific for your vehicle: do not use them
on different models and do not use
bolts from other models on your car.
WARNING
Repair and refit the standard
wheel as soon as possible.
Do not apply grease to the bolt
threads before assembly: they might
spontaneously unscrew.
WARNING
BUMP STARTING
Never bump start the engine by pushing,
towing or driving downhill. This could
cause fuel to flow into the catalytic con-
verter and damage it beyond repair.
IMPORTANT Remember that the brake
booster and the power steering system
are not active until the engine is started,
so you will need to apply much more force
to the brake pedal or steering wheel.
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 135

136SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Important notes:❒
the jack weight is 1.76 kg;
❒
the jack requires no adjustment;
❒
the jack cannot be repaired. If it breaks
it must be replaced with a new jack;
❒
no tool other than its cranking device
may be fitted on the jack.
To change a wheel proceed
as follows:
❒
stop the car where it is not a danger to
other road users and you can replace
the wheel safely. The ground should be
flat and solid;
❒
turn the engine off and pull up the hand-
brake.
❒
engage first gear or reverse;
❒
wear the reflective safety jacket (com-
pulsory by law in certain countries) be-
fore getting out of the car;
❒
open the boot and lift the carpet or re-
move the cargo box (for versions/mar-
kets, where provided);
❒
unscrew the locking device A-fig. 2;
❒
take out the tool container C-fig. 2and
put it alongside the wheel to be
changed;
❒
take out the spare wheel B-fig. 2;
fig. 2
F0M0188m
The jack may be used to re-
place wheels only on the car
which it equips or other cars of the
same model. Never use the jack for
other purposes, such as lifting other
models. Never use the jack to carry
out repairs under the car. Incorrect
positioning of the jack may cause the
car to fall. Do not use the jack for
loads higher than the one shown on
its label.
WARNING
Incorrect hub cap assembly
may cause it to come off
when the car is moving. Never tam-
per with the inflation valve. Never in-
troduce tools of any kind between the
rim and the tyre. Check tyre and
spare wheel pressure regularly, refer-
ring to the values shown in the “Tech-
nical specifications” section.
WARNING
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 136

138SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
for versions with hub caps, remove the
cap after unscrewing the 3 fastening
bolts and finally unscrew the fourth bolt
L-fig. 5and remove the wheel;
❒
make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not come
loose;
❒
fit the spare wheel by inserting the first
bolt two threads into the hole closest
to the inflation valve;
❒
fit the hub cap by aligning the crescent
hole with the bolt you have fitted us-
ing the wrench;
❒
tighten the fastening bolts;
❒
turn the jack handle L-fig. 4to lower
the car and remove the jack;
❒
use the wrench provided to fasten the
bolts completely in a criss-cross fash-
ion as per the order illustrated in fig. 6;
❒
if you are replacing an alloy wheel and
wish to store it temporarily in the spare
wheel compartment, you should posi-
tion it upside down.REFITTING A STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
fig. 5
F0M0192m
fig. 6
F0M0194m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 138

139
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Versions with steel rims
Proceed as follows:❒
make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will not
come loose;
❒
fit the standard wheel by inserting the
first bolt two threads into the hole clos-
est to the inflation valve;
❒
fit the hub cap by aligning the crescent
hole with the bolt you have fitted, then
insert the other 3 bolts;
❒
using the wrench provided, tighten the
fastening bolts;
❒
lower the car and remove the jack;
❒
using the wrench provided, fully tight-
en the bolts in the sequence shown
previously.Versions with alloy rims
Proceed as follows:
❒
place the wheel onto the hub and tight-
en the bolts using the wrench provided;
❒
lower the car and remove the jack;
❒
using the wrench provided, fully tight-
en the bolts in the sequence shown
previously.When you have finished
❒
stow the spare wheel in the space pro-
vided in the boot;
❒
put the jack back in its container C-
fig. 2partially open by forcing it slight-
ly against the container walls to prevent
it from rattling around when travelling;
❒
put the tools back into their places in
the container;
❒
stow the container C-fig. 2, complete
with tools, inside the spare wheel;
❒
tighten the tool container clamping de-
vice A-fig. 2;
❒
refit the boot carpet or the Cargo box
(for versions/markets, where provid-
ed).
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 139

179
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESIN AN
EMERGENCYTECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESSERVICE
AND CARE
WHEELS AND TYRESCheck the pressure of each tyre, includ-
ing the spare, every two weeks and before
long journeys. The pressure should be
checked with the tyre rested and cold.
It is normal for the pressure to increase
when the car is used; for the correct tyre
inflation pressure, see “Wheels” in the
“Technical specifications” section.
Incorrect pressure causes abnormal tyre
wearfig. 10:
Anormal pressure: tread evenly worn.
Blow pressure: tread particularly worn
at the edges.
Chigh pressure: tread particularly worn
in the centre.
The tyres must be replaced when the
tread is less than 1.6 mm thick. In all cas-
es, follow the laws in force in the coun-
try where you are driving.
fig. 10
F0M0160m
IMPORTANT NOTES❒
Where possible, avoid braking sudden-
ly, wheel-spinning and crashing into
curbs, potholes or other obstacles.
Long distances on uneven roads can
damage the tyres;
❒
check the tyres regularly for cuts on the
sides, swelling or irregular tread wear.
Go to a Fiat Dealership if required.
❒
avoid overloading the car when travel-
ling: this may cause serious damage to
the wheels and tyres;
❒
if a tyre is punctured, stop the vehicle
immediately and change it to avoid
damage to the tyre, the rim, and the
suspension and steering systems;
❒
a tyre will age even if it is not used much.
Cracks in the tread and on the sidewalls
are a sign of ageing. In any event, have
the tyres checked by specialised per-
sonnel if they have been fitted for longer
than 6 years. Remember to check the
spare wheel very carefully;
❒
in case of replacement, always fit new
tyres, avoiding those with an unknown
origin;
❒
if a tyre is replaced, you should also
change the inflation valve;
❒
to allow even wear between the front
and rear tyres, it is advisable to switch
them every 10-15 thousand kilometres,
keeping them on the same side of the
car so as not to reverse the direction
of rotation.
Remember that the road
holding qualities of your car
also depend on correct tyre pressures.
WARNING
165-184 PUNTO POP 1ed EN 11/10/13 14.56 Pagina 179

192SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESIN AN
EMERGENCYSERVICE
AND CAREINDEXCONTROLS
AND DEVICESTECHNICAL
SPECIFICATIONS
Maximum speed index
Q= up to 160 km/h.
R= up to 170 km/h.
S= up to 180 km/h.
T= up to 190 km/h.
U= up to 200 km/h.
H= up to 210 km/h.
V= up to 240 km/h.
Maximum speed index
for snow tyres
QM + S= up to 160 km/h.
TM + S= up to 190 km/h.
HM + S= up to 210 km/h.
WHEELSRIMS AND TYRES
Pressed steel or alloy rims. Tubeless ra-
dial carcass tyres. All approved tyres are
listed in the Log Book.
IMPORTANT In the event of discrepan-
cies between the information provided in
this Owner Handbook and the Log Book,
the latter takes precedence.
For safety when driving, it is essential that
the car is fitted with tyres of the same
make and type on all wheels.
IMPORTANT Do not use inner tubes
with tubeless tyres.
SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Total front toe-in: 1 ± 1 mm
Total rear toe-in: 1.7 ± 2 mm.
The values refer to the car in running
order.
fig. 4
F0M0169m
READING TYRE
MARKINGS fig. 4
Example: 175/65 R 15 84T
175 = Nominal width (S, distance in mm
between sidewalls).
65 = Height/width ratio (H/S) as a per-
centage.
R = Radial tyre.
15 = Rim diameter in inches (Ø).
84 = Load index.
T = Maximum speed index.
185-208 PUNTO POP 1ed EN 24/09/13 14.26 Pagina 192

194SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESIN AN
EMERGENCYSERVICE
AND CAREINDEXCONTROLS
AND DEVICESTECHNICAL
SPECIFICATIONS
2.2 2.1
2.2 2.2
2.2 2.0
2.2 2.2
2.2 2.1
2.2 2.2
2.2 2.0
2.2 2.22.4 2.1
2.5 2.2
2.3 2.1
2.3 2.3
COLD TYRE INFLATION PRESSURE (bar)Versions 1.2 1.4 1.3 Multijet
Front Rear Front Rear Front Rear
175/
65 R15 84T
Medium load Full load
185/65 R15 88T
Medium load Full loadAdd +0.3 bar to the prescribed pressure when the tyres are warm. However, recheck that the value is correct with the tyre cold.
With snow tyres, add +0.2 bar to the pressure recommended for standard tyres.
When running at speeds higher than 160 km/h, inflate tyres to full-load pressures.175/65 R15 84T (M+S)
185/65 R15 88T (M+S)
185/65 R15 88T (M+S) 175/65 R15 84T
185/65 R15 88T
185/65 R15 88T6J X 15'' - ET 43175/65 R15 84T
185/65 R15 88T 6J X 15'' - ET 43
6J X 15'' - ET 43 (▲)
6J X 15'' - ET 43 (▲)Version Rims (*) Tyres Spare wheel (
ç)
provided snow Rim (*) Tyre
1.2 - 1.4 1.3 Multijet 75HP
1.3 Multijet 85HP
(▲) OPT Alloy rim
(*) 100 mm wheel stud distance and M12 x 1.5 studs; use only wheels specified for this car.
(ç) Depending on the configuration, the spare wheel has a 175/65 R15 84T tyre and a 6J×15''- ET43 rim. In this case the
175/65 R15 84T tyre has the same specifications as the spare wheel: the information in “Changing a tyre” therefore refers to
the 175/65 R15 84T tyre.
185-208 PUNTO POP 1ed EN 24/09/13 14.26 Pagina 194

212SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESIN AN
EMERGENCYSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICES
Tailgate .......................................... 65
Technical specifications ............... 185
Third brake light ........................... 151
Tool kit............................................ 136
Top speeds ..................................... 195
Towing the car .............................. 163
Towing trailers .............................. 116
– installing the tow hook .......... 117
Transmission .................................. 190
Trip computer ............................... 30
Tyre pressures .............................. 194
Tyres
– changing .................................... 135
– correct tyre reading ............... 192
– inflation pressure .................... 195
– maintenance ............................. 179
– provided as standard ............. 194U
sing the manual gearbox ......... 114
W
arning lights and messages .... 121
Weights .......................................... 197
Wheel geometry............................ 194
Wheel rims
– reading rim code ...................... 193
Wheels
– changing .................................... 135
– spare wheel ............................... 192
– wheel geometry ...................... 192Window washing .......................... 49
Windows (cleaning) ..................... 183
Windscreen and rear
window wiper blades ................ 181
Windscreen washer
– control ...................................... 49
– fluid level ................................... 176
Windscreen wiper
– blades.......................................... 181
– control ...................................... 49
– nozzles........................................ 181
Windscreen/rear window
washer level .................................. 176
Wiring for Portable navigation
system............................................ 84 Sliding columns
– type............................................. 189
Smart washing ............................... 49
Snow chains ................................... 119
Snow tyres ..................................... 194
Speedometer ................................. 14
Start&Stop system......................... 79
Starting and driving ....................... 109
Starting the engine
– bump starting ........................... 134
– emergency starting ................. 134
– how to warm up the engine
after it has just started .......... 114
– ignition switch ......................... 12
– jump starting ............................ 134
– procedure for diesel
versions .................................... 111
– procedure for petrol
versions .................................... 112
– stopping the engine ................ 114
Steering wheel (adjustment) ...... 35
Steering wheel adjustment ......... 35
Steering wheel lock ...................... 12
Steering ........................................... 191
Sun visors ....................................... 59
Suspensions .................................... 191
Symbols ........................................... 6
209-214 PUNTO POP 1ed EN 25/09/13 15.38 Pagina 212