2014 FIAT PUNTO brake light

144SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
if you get a pressure reading of at least
1.8 bar, restore the proper pressure
(with engine running and handbrake on)
and restart;
❒
drive with the utmost care to the near-
est Fiat Dealership.
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor may also be used for
restoring pressure only. Release the fast
coupling and connect it directly to the tyre
valve fig. 13; in this way, the cylinder will
not be connected to the compressor and
no sealant will be injected. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder, proceed as fol-
lows:
❒
disconnect A-fig. 14;
❒
turn the cylinder anticlockwise to lift
it out;
❒
insert the new cylinder and turn it
clockwise;
❒
connect Ato the cylinder and fit the
transparent tube Binto its allocated
space.
Remember to inform the
workshop that the tyre has
been treated with a quick repair kit.
Give the instruction booklet to the
personnel charged with handling the
treated tyre.
WARNING
fig. 13
F0M0365m
fig. 14
F0M0206m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 144

146SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Bulbs Figure ref. Type PowerMain beams/Dipped beams Daylight lightsFront sidelights Front fog lights (for versions/markets, where provided)Front direction indicators Side direction indicators Rear direction indicators Tailights Brake lights Third brake light Reverse lights Rear fog lights Number plate lights Front ceiling light with movable lens
Front ceiling light with spot lights
H4
W21W
W5W
H11
PY21W
WY5W
PY21W
LED
P21W
W2,3W
W16W
W16W
W5W
C10W
C10W D
A
A
–
B
A
B
–
B
B
–
–
A
C
C55 W/60 W
21W
5W
55W
21W
5W
21W
–
21W
2,3W
16W
16W
5W
10W
10W
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 146

150SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
remove the bulb A-fig. 25by ro-
tating it counter-clockwise and dis-
connect the electrical connector.
REAR LIGHT CLUSTERS
The rear light clusters contain taillight,
brake light and direction indicator bulbs.
The bulbs are arranged inside the light
cluster fig. 26as follows:
Ddirection indicators
Ebrake lights.
To change the bulb proceed as follows:❒
undo both fastening bolts A-fig 26;
❒
disconnect the central electric connec-
tor Band pull the lens unit outwards;
❒
unhook the bulb holder by unclipping
the fasteners C-fig. 27;
❒
remove the bulb by pushing it in gen-
tly and turning anti-clockwise (“bayo-
net” clamping), then replace it;
❒
refit the bulb holder;
❒
reconnect the electric connector, cor-
rectly realign the unit with the car body
and then tighten the fastening screws
A.IMPORTANT To replace the LED tail-
lights you must contact a Fiat Dealership.
fig. 25
A
F0M0639m
fig. 26
F0M0640m
fig. 27
F0M0641m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 150

151
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
REAR FOG LIGHTS fig. 28
Contact a Fiat Dealership to have bulbs
for the rear fog lights Areplaced.
REVERSE LIGHTS fig. 28
Contact a Fiat Dealership to have bulbs
for the reverse lights Breplaced.THIRD BRAKE LIGHT fig. 29
To change the bulb proceed as follows:
❒
open the boot;
❒
remove the rubber caps;
❒
press in the catches and remove the
lens unit C;
❒
disconnect the electric connector;
❒
press in the tabs Dand remove the
bulb holder;
❒
remove the snap-fitted bulb and replace
it.NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❒
manipulate the point shown by the ar-
row and remove the lens unit A-
fig. 30;
❒
change the bulbfig. 31 by releasing it
from the side contacts and making
sure the new bulb is correctly fastened
between these contacts;
❒
refit the snap-fitted lens unit.
fig. 28
F0M0642m
fig. 29
F0M0643m
fig. 30
F0M0644m
fig. 31
F0M0645m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 151

157
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
1 (*)
8 (*)
8
13
2 (*)
5
11
4
6
14
7
12
3
107,5
7,5
5
5
5
10
5
20
20
20
20
5
5
7,5 FUSE TABLE
Dashboard fusebox fig. 36
DEVICESFUSE AMPSRight dipped beam headlightLeft dipped beam headlightHeadlamp alignment corrector
INT/A supply for switch coils on engine fusebox and switch coils on body computer control unitFront ceiling light, rear ceiling light (VAN version)
Supply and battery for EOBD diagnostic plug, alarm, sound system, Blue&Me™control unit
INT supply for instrument panel, switch on brake pedal (N.O. contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot unlocking motorWindscreen/rear window washer pumpElectric window motor on driver-side front doorElectric window motor on passenger-side front door
INT supply for dashboard control lights, mirror movement exterior electrics, sunroof control unit, My Port infotelematic system socketInstrument panel
INT supply for brake pedal switch (NC contact), clutch pedal switch,
interior heating unit, Blue&Me™control unit, sound system capabilities,
voltage stabiliser control unit, reverse light on rear bumper, water sensor
on diesel filter, glow plug heating control unit, airflow meter, brake booster sensor, switch coils on engine compartment fusebox(*) Fuse on some versions only.
133-164 PUNTO POP 1ed EN 29/08/13 15.08 Pagina 157

163
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
fig. 41
F0M601m
RAISING THE CARIf the car needs to be lifted, go to a Fiat
Dealership which is equipped with the arm
hoist or workshop lift.
The car should be lifted side-on only, by
putting the ends of the arms or the work-
shop lifting device in the areas shown in
the diagram.
IMPORTANT For the Sport versions, take
care not to damage the side skirts when
raising the car side-on with the workshop
lifting device.
TOWING THE CARThe tow ring provided with the car is
housed in the tool box under the carpet
in the boot.
FASTENING THE TOW RING
fig. 44-45
Proceed as follows:❒
release the cap A;
❒
take the tow ring Bfrom its support;
❒
screw the ring onto the rear or front
threaded pin.
The brake booster and pow-
er steering will not work
while the vehicle is being towed. You
will therefore need to apply more
force to the brake pedal and steering
wheel. Do not use bendy cables for
towing and avoid jerking. Make sure
not to damage parts in contact with
the car while towing. Respect the
rules of the highway code when tow-
ing the car, specifically in relation to
the towing device and road conduct.
WARNING
fig. 44
F0M602m
fig. 45
F0M603m
133-164 PUNTO POP 1ed EN 29/08/13 15.08 Pagina 163

164SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Do not start the engine while
the car is being towed.
WARNING
Clean the threaded housing
carefully before fastening
the ring. Make sure that the ring is se-
curely fastened before towing the car.
WARNING
Release the steering wheel
lock before towing (see “Ig-
nition device” in “Dashboard and
controls”). The brake booster and
power steering will not work while the
vehicle is being towed. You will there-
fore need to apply more force to the
brake pedal and steering wheel. Do
not use bendy cables for towing and
avoid jerking. Make sure not to dam-
age parts in contact with the car
while towing. Respect the rules of the
highway code when towing the car,
specifically in relation to the towing
device and road conduct.
WARNING
The front and rear tow
hooks should be used only
for emergencies on the road. You are
allowed to tow the car for short dis-
tances using an appropriate device in
accordance with the highway code
(a rigid bar), to move the vehicle on
the road in readiness for towing or
transporting via a breakdown vehicle.
Tow hooks MUST NOT be used to
tow vehicles off the road or where
there are obstacles and/or for tow-
ing operations using cables or other
non-rigid devices.
Respecting the above conditions,
towing must take place with two ve-
hicles (one towing, the other towed)
aligned as much as possible along the
same centre line.
WARNING
133-164 PUNTO POP 1ed EN 29/08/13 15.08 Pagina 164

167
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESIN AN
EMERGENCYTECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESSERVICE
AND CARE
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●●
●●
●●
●● ●
●● ●● ● ●
SCHEDULED SERVICING PLANEURO 4, EURO 5, EURO 6 PETROL AND EURO 4 DIESEL VERSIONS
Thousands of miles 18 36 54 72 90 108
Thousands of kilometres 30 60 90 120 150 180
Months 24 48 72 96 120 144
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlamps, direction indicators,
hazard warning lights, boot, passenger compartment, glove box, instrument panel warning lights, etc.)Check operation of windscreen washer system and adjust nozzles if necessary.Check windscreen/rear window wiper blade position/wear
Check conditions and wear of front/rear disc brake pads (for versions/markets where provided) and operation of pad wear indicatorCheck condition and wear of rear drum brake linings
Visually inspect the conditions of: bodywork,
underbody protection, pipes and tubes (exhaust – fuel – brakes), rubber parts (boots, sleeves, bushes, etc.)
Check cleanliness of bonnet and boot locks, and the cleanliness and lubrication of linkages
Check and, if necessary, top up fluid levels (brakes/hydraulic clutch, windscreen washer, battery, engine coolant, etc.) Check the handbrake lever stroke and adjust it, if necessaryVisually inspect the condition of accessory drive belt/s.Visually inspect the condition of toothed timing belt
Check tension of accessory drive belt/s, and adjust if necessary (versions 1.2 – 1.4 heated)Check and, if necessary, adjust tappet clearance (1.2
8v – 1.4
8vversions)
Check exhaust gas emissions
165-184 PUNTO POP 1ed EN 11/10/13 14.56 Pagina 167