2014 FIAT PANDA Esc

CARRYING CHILDREN SAFELYAll vehicle's occupants must be protected, babies and
children included! For optimal protection in the
event of a collision, all passengers must be seated
and wearing adequate restraint systems.
This prescription is compulsory in all EC countries
according to EC Directive 2003/20/EC.
This is even more important for children since their
head is larger and heavier than an adult's in
proportion to their body, while their muscular and
bone structures are not fully developed.
Therefore, correct restraint systems other than adult
seat belts are necessary to reduce as much as
possible the risk of injuries in case of accident,
braking or sudden manoeuvre.
Children must be suitably restrained inside the
vehicle according to their body: weight and height.
Several children restraint system types are available;
always choose the one most suitable for the child.
In Europe the characteristics of children restraint
systems are ruled by the regulation ECE-R44, dividing
them into five weight groups:Group Weight groups
Group0 upto10kg
Group 0+ up to 13 kg
Group 1 9-18 kg
Group 2 15-25 kg
Group 3 22-36 kg
All restraint devices must bear the type-approval
data along with the control mark on a label firmly
secured to the child seat which must never be
removed.
Over 1.50 m in height, from the point of view of
restraint systems, children are considered as adults
and wear the seat belts normally. Lineaccessori
Fiat offers child restraint systems for each weight
group. These devices are recommended having been
specifically designed for Fiat cars.
WARNING
When an active passenger air bag is
fitted, DO NOT install backwards-facing
child seats on the front seat . Deployment of the
air bag in an accident could cause fatal injuries
to the baby regardless of the severity of the
collision. It is advisable to always carr y children
in a child seat on the rear seat , which is the
most protected position in the event of a
collision.
107GETTING TO KNOW
YOUR CARSAFETYSTARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Deactivation of passenger side front air bag
and side bag for chest/pelvis protection (for
versions/markets, where provided)
If a child must be carried in backwards-facing seat on
the front seat, deactivate the front passenger side
air bag and side bags for chest/shoulder protection
(for versions/markets where provided). With the air
bags deactivated, the
warning light switches on
in the instrument panel.
IMPORTANT To deactivate the air bags see the
description in the "Getting to know your car"
chapter, "Menu Options" paragraph.
SIDE BAGS (Side bag - Window bag)
The car is fitted with front side airbags for driver and
passenger (for versions/markets where provided)
for protecting the chest and pelvis, and window bags
(for versions/markets where provided) for protecting
the heads of front and rear occupants.
Side bags protect occupants from side-on crashes of
medium/high severity by placing the bag between
the occupant and the internal parts of the side
structure of the vehicle.
Non-activation of side bags in other types of
collisions (head-on collisions, rear shunts, roll-overs,
etc...) is not an indication of system malfunction.Side bags
(for versions/markets, where provided)
These comprise two types of bags located in the
front seat backrests fig. 106 which protect the chest
and shoulder area of the occupants in the event of
a side impact of medium-high severity.
fig. 106
F0W0203
117GETTING TO KNOW
YOUR CARSAFETYSTARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

WARNING
Afaultwiththe
warning light is
indicated by flashing of the
warning
light , which signals the deactivation of the
passenger side front airbag. In addition, the
airbag system automatically disables the
airbags on the passenger's side (front and side
bags - for versions/markets, where provided).
In this case, the
warning light may not
indicate faults in the restraint systems. Before
continuing, contact a Fiat Dealership
immediately to have the system checked.
PASSENGER/SIDE AIRBAGS
DEACTIVATED (amber)
(for versions/markets, where provided)
The
warning light switches on when the front
passenger's airbag and side bag are disabled. With
front passenger airbag on, when the ignition key
is turned to MAR, the
warning light switches on
constantly for several seconds, it flashes for another
few seconds and then it should switch off.
WARNING
A failure of the
warning light is
indicated by
warning light switching
on. In addition, the airbag system automatically
disables the airbags on the passenger's side
(front and side bags where provided). Before
continuing, contact a Fiat Dealership
immediately to have the system checked.
SEAT BELTS NOT FASTENED (red)
(for versions/markets, where provided)
The warning light switches on constantly with the
car stationary and the driver's side or passenger side
seat belt (when the passenger is present) not
fastened. The warning light will flash and a buzzer will
sound if the car is in motion and the front seat belts
are not correctly fastened.
Contact a Fiat Dealership if you wish to permanently
deactivate the SBR (Seat Belt Reminder) system
buzzer. The system can be reactivated using the
Setup menu (see the description in the "Knowing
your car" section).
134
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND MESSAGESIN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

LOW BATTERY CHARGE (red)
(for versions/markets, where provided)
When the ignition key is turned to MAR, the warning
light switches on but should switch off as soon as
the engine is started (with the engine idling, a brief
delay is acceptable).
If the warning light (or, on some versions, a message
and a symbol on the display) remains on constantly
or flashing, contact a Fiat Dealership.ON CONSTANTLY: LOW ENGINE
OIL PRESSURE (red)
ON FLASHING: ENGINE OIL
DETERIORATED
(only Diesel versions with DPF - red)
When the ignition key is turned to MAR, the warning
light switches on but should switch off as soon as
the engine is started.
1. Low engine oil pressure
The warning light switches on constantly together
(for versions/markets, where provided) with a
message on the display when the system detects that
the engine oil pressure is too low.
WARNING
If the
warning light switches on
when driving (on certain versions
together with the message on the display) stop
the engine immediately and contact a Fiat
Dealership.
2. Engine oil deteriorated
(only Diesel versions with DPF)
The warning light will flash and a specific message will
appear on the display (in versions/markets, where
provided). The warning light flashes for 3 minute
cycles with the warning light off for intervals of
5 seconds until oil is changed.
After the first indication, at each engine start-up the
warning light will continue flashing as described
above until the oil is changed. The display shows a
dedicated message (for versions/markets, where
provided) together with the warning light.
The flashing of this warning light should not be
considered as a fault; it informs the customer that
the oil needs to be changed following normal car use.
Remember that the deterioration of the engine oil
is accelerated by:
❒mainly town use of the car which makes the DPF
regeneration process more frequent;
135GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND MESSAGESIN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒use of the car for short drives, in which the engine
does not have time to reach its regular operating
temperature;
❒repeated interruption of the regeneration process,
signalled by the DPF warning light switching on.
WARNING
If the warning light switches on, the
deteriorated engine oil must be changed
as soon as possible, and never more than 500
km from the first time that the warning light
switches on. Failure to observe the above may
result in severe damage to the engine and
invalidate the warranty. Remember that the
operation of this warning light is not related to
the amount of oil in the engine.Therefore,
never top up with oil when the light starts
flashing.EXCESSIVE ENGINE COOLANT
TEMPERATURE (red)
Turning the key to MAR switches on the warning
light, but it should switch off after a few seconds.
The warning light switches on (on some versions,
with a message on the display and a symbol on
the display) when the engine is overheated.If the warning light comes on when driving, proceed
as follows:
❒when driving normally:stop the car, stop the
engine and check that the water level in the
reservoir is not below the MIN mark. If it is, wait
for a few minutes for the engine to cool down
then slowly and carefully open the cap, top up with
coolant and check that the level is between the
MIN and MAX marks. Also check visually for any
fluid leaks. If, when restarting, the warning light
should switch on again, contact a Fiat Dealership;
❒if the car is used under demanding
conditions(e.g. towing trailers uphill or fully
loaded): slow down and, if the light stays on, stop
the car. Wait for 2 or 3 minutes with the engine
running and slightly accelerated to further favour
the coolant circulation. Then stop the engine.
Check the correct liquid level as described above.
IMPORTANT On demanding routes, it is advisable to
keep the engine on and slightly accelerated for a
few minutes before stopping it.
FUEL RESERVE - LIMITED RANGE
(amber)
This warning light comes on when about 5 to 7 litres
of fuel are left in the tank. When the remaining
range is lower than approx. 50 km (or equivalent
value in miles), on some versions, the display will
show a warning message.
136
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND MESSAGESIN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IMPORTANT The warning light will flash to indicate
a system failure. If this is the case, go to a Fiat
Dealership to have the system checked.
EOBD/INJECTION SYSTEM
FAILURE (amber)
In normal conditions, the warning light switches on
when the key is turned to MAR (on some versions,
with a message on the display), but should switch off
as soon as the engine is started.
If the warning light remains on or switches on whilst
driving, the injection system is not working properly;
in particular, if the warning light switches on
constantly, this indicates a malfunction in the
supply/ignition system that could cause excessive
exhaust emissions, a possible loss of performance,
poor driveability and high fuel consumption.
In these conditions, you can continue driving without
demanding excessive effort or speed from the
engine. Prolonged use of the car with the warning
light on may cause damage: contact a Fiat Dealership
as soon as possible.
The warning light switches off after the malfunction
disappears, but the notification is stored in the
system.
NOTE (valid only for petrol engines)
If the warning light flashes, the catalytic converter
may be damaged.In this case, it is necessary to release the accelerator
pedal to lower the speed of the engine until the
warning light stops flashing; continue the journey at
moderate speed, trying to avoid driving conditions
that may cause further flashing and contact a Fiat
Dealership as soon as possible.
Contact a Fiat Dealership as soon as
possible if the
warning light either does
notswitchonwhenthekeyisturnedto
MAR or if while driving the warning light switches
on either constantly or flashing (along with a
message and a symbol on the display on some
versions). Operation of the
warning light may
be verified by traffic control officers using
appropriate equipment . Comply with the laws
and regulations of the country where you are
driving.
ESC SYSTEM FAILURE (amber)
(for versions/markets, where provided)
This warning light switches on when the ignition key
is turned to MAR, but it should switch off after a
few seconds. If the warning light does not switch off
or stays on (along with a message on the display
on some versions) whilst driving, contact a Fiat
Dealership. Flashing of the warning light while driving
indicates the intervention of the ESC system.
137GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND MESSAGESIN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IMPORTANT After the battery is disconnected, the
steering must be initialised. The warning light
switches on to indicate this. To carry out this
procedure, simply turn the steering wheel all the way
from one end to the other or drive in a straight line
for about a hundred metres.
DPF (PARTICULATE FILTER)
CLEANING IN PROGRESS
(only diesel versions with DPF) (amber)
This warning light switches on when the ignition key
is turned to MAR, but it should switch off after a
few seconds. The warning light (together with a
message and a symbol on the display on some
versions) switches on constantly to notify the driver
that the DPF system needs to eliminate captured
pollutants (particulate) through the regeneration
process.
The warning light does not switch on during every
DPF regeneration, but only when driving conditions
require that the driver is notified. To switch the
warning light off, the car must be kept in motion
until the regeneration process is completed.
On average, the process lasts fifteen minutes.
Optimal conditions for completing the process are
achieved by travelling at 60 km/h with engine revs
above 2000 rpm.
If this light switches on, it does not mean that the
car is defective, so there is no need to take it to
a garage. A specific message will appear on thedisplay when the warning light comes on (for
versions/markets, where provided).
WARNING
The driving speed must always be
suitable for traffic and weather
conditions and the driver must always comply
with the Highway Code.The engine can be
stopped even if the DPF warning light is on;
however, repeated interruptions of the
regeneration process could cause premature
deterioration of the engine oil. For this reason,
always wait until the warning light switches
off before stopping the engine as described
above. It is not advisable to complete DPF
regeneration with the car stationar y.GENERIC FAILURE INDICATION
(amber)
(for versions/markets, where provided)
The warning light switches on in the following
circumstances. In these cases contact a Fiat
Dealership to have the fault eliminated as soon as
possible.
139GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND MESSAGESIN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Restore the standard wheel as soon as possible,
because, once placed in the associated compartment,
the luggage compartment load platform is rendered
uneven as the standard wheel is larger than the
space-saver wheel.
REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise
the car and remove the space-saver wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces between standard
wheel and hub are clean so that the fastening
bolts will not come loose;
❒fit the standard wheel by inserting the first bolt by
2 threads into the hole closest to the inflation
valve;❒fit the hub cap, aligning the crescent hole with the
bolt already fitted, then fit the other bolts;
❒using the wrench provided, tighten the fastening
bolts;
❒lower the car and remove the jack;
❒using the wrench provided, fully tighten the bolts
in the sequence shown previously.
Versions with alloy wheels
❒insert the wheel on the hub and using the wrench
provided tighten the bolts;
❒lower the car and remove the jack;
❒using the wrench provided, fully tighten the bolts
in the sequence shown;
❒reinstall the pressure-fitted hub cap, making sure
that the reference hole on the wheel is aligned
with the reference hole on the cap.
IMPORTANT If it is not fitted properly, the hub cap
may detach itself when the vehicle is running.
At the end of operation
❒stow the space-saver wheel in the compartment
provided in the luggage compartment;
❒insert the jack and the other tools in the
container;
❒arrange the container and tools on the space-saver
wheel;
❒correctly reposition the boot mat.
fig. 116
F0W0182
148
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX