2014 FIAT FREEMONT seats

• X = ISOFIX position not suitable for ISOFIX childrestraint systems in this mass group and / or this size
class.
• * = Seats in front of child restraint seats may need to be adjusted forward to install the child restraint seat.
• ** = No access to 3rd row seating positions if Carrycot is installed in vehicle.There are different sizes and types of restraints for
children from newborn size to the child almost large
enough for an adult safety belt. Always check the child
seat Owner's Manual to ensure you have the correct seat
for your child. Before buying any restraint system, make
sure that it has a label certifying that it meets all appli-
cable Safety Standards. You should also make sure that
you can install it in the vehicle where you will use it.
Summary Of Recommendations For Restraining Children In Vehicles
Child Size, Height,
Weight or Age Recommended Type of
Child Restraint
Infants and Toddlers Children who are two years old or
younger and who have not reached the height or weight limits of their child restraint Either an Infant Carrier or a Convert-
ible Child Restraint, facing rearward in the rear seat of the vehicle
Small Children Children who are at least two years
old or who have out-grown theheight or weight limit of their rear-facing child restraint Forward-Facing Child Restraint with a
five-point Harness, facing forward in the rear seat of the vehicle
Larger Children Children who have out-grown their
forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt Belt Positioning Booster Seat and the
vehicle seat belt, seated in the rear seat of the vehicle
Children Too Large for Child Restraints Children 12 years old or younger,
who have out-grown the height or weight limit of their booster seat Vehicle Seat Belt, seated in the rear
seat of the vehicle
203
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Infants And Child Restraints
Safety experts recommend that children ride
rearward-facing in the vehicle until they are two years
old or until they reach either the height or weight limit
of their rear facing child safety seat. Two types of child
restraints can be used rearward-facing: infant carriers
and convertible child seats.
The infant carrier is only used rearward-facing in the
vehicle. It is recommended for children from birth until
they reach the weight or height limit of the infant
carrier. Convertible child seats can be used either
rearward-facing or forward-facing in the vehicle. Con-
vertible child seats often have a higher weight limit in
the rearward-facing direction than infant carriers do, so
they can be used rearward-facing by children who have
outgrown their infant carrier but are still less than at
least two years old. Children should remain rearward-
facing until they reach the highest weight or height
allowed by their convertible child seat.WARNING!
• Never place a rear facing infant seat in
front of

an air bag. A deploying Passen-
ger Advanced Front Air Bag can cause death or
serious injury to a child 12 years or younger,
including a child in a rearward facing infant seat .
• Only use a rearward-facing child restraint in a
vehicle with a rear seat .
Older Children And Child Restraints
Children who are two years old or who have outgrown
their rear-facing convertible child seat can ride
forward-facing in the vehicle. Forward-facing child
seats and convertible child seats used in the forward-
facing direction are for children who are over two years
old or who have outgrown the rear-facing weight or
height limit of their rear-facing convertible child seat.
Children should remain in a forward-facing child seat
with a harness for as long as possible, up to the highest
weight or height allowed by the child seat.
All children whose weight or height is above the
forward-facing limit for the child seat should use a
belt-positioning booster seat until the vehicle’s seat
204
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

WARNING!
Securely lock the seat cushion into posi-
tion bef

ore using the seat . Otherwise,
the seat will not provide the proper stability for
child seats and/or passengers. An improperly
latched seat cushion could cause serious injury.
Children Too Large For Booster Seats
Children who are large enough to wear the shoulder
belt comfortably, and whose legs are long enough to
bend over the front of the seat when their back is
against the seatback, should use the seat belt in a rear
seat. Use this simple 5-step test to decide whether the
child can use the vehicle’s seat belt alone:
1. Can the child sit all the way back against the back of the vehicle seat? 2. Do the child’s knees bend comfortably over the
front of the vehicle seat – while they are still sitting
all the way back?
3. Does the shoulder belt cross the child’s shoulder between their neck and arm?
4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach?
5. Can the child stay seated like this for the whole trip?
If the answer to any of these questions was “no,” then
the child still needs to use a booster seat in this vehicle.
If the child is using the lap/shoulder belt, check belt fit
periodically. A child’s squirming or slouching can move
the belt out of position. If the shoulder belt contacts
the face or neck, move the child closer to the center of
the vehicle. Never allow a child to put the shoulder belt
under an arm or behind their back.
207
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Recommendations For Attaching Child Restraints
Restraint TypeCombined
Weight of the Child + Child Restraint Use any attachment method shown with an “X” Below
ISOFIX – Lower
Anchors Only Seat Belt Only ISOFIX –
Lower
Anchors + Top
Tether Anchor Seat Belt + Top
Tether Anchor
Rear-Facing Child Restraint Up to 29 kg
XX
Rear-Facing Child Restraint More than 29 kg
X
Forward-Facing Child Restraint Up to 29 kg
XX
Forward-Facing Child Restraint More than 29 kg
X
ISOFIX Restraint System
Your vehicle is equipped with the child restraint an-
chorage system called ISOFIX. The ISOFIX system has
three vehicle anchor points for installing ISOFIX-
equipped child seats. There are two lower anchorages
located at the back of the seat cushion where it meets
the seatback and one top tether anchorage locatedbehind the seating position. These anchorages are used
to install ISOFIX-equipped child seats without using
the vehicle’s seat belts. Some seating positions may
have a top tether anchorage but no lower anchorages.
In these seating positions, the seat belt must be used
with the top tether anchorage to install the child
restraint.
208
KNOWING
YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Center Seat ISOFIX
This vehicle has 5 lower ISOFIX anchorages in the rear
seat. Anchorages A and B are used for the right out-
board position behind the front passenger (1). Anchor-
ages D and E are used for the left outboard position
behind the driver (3). Anchorages B and C are used for
the center seating position (2). Do not install an ISO-
FIX child restraint using anchorages C and D. This is
not a ISOFIX position in your vehicle.
You can install up to two child seats using the ISOFIX
system at the same time. If you are installing three child
restraints, you must use the seatbelt to install the
center child restraint. You can use either the ISOFIX
anchors for positions (1) and (3) or the vehicle’s seat
belt for installing the child seats in the outboard posi-
tions.
(fig. 145)
Options for installing two child seats using the ISOFIX
anchorages in this vehicle:
1. Right and left outboard seating positions (1 and 3):Install the child seats in the right and left outboard
seating positions using lower anchorages A and B,
and D and E. Do not use the center seat anchorage,
C. If the child seats do not block the center seat belt
webbing and buckle, the center seat belt can be
used to restraint an occupant or child restraint in
the center seating position.
2. Left outboard and center seating positions (3 and 2): Install the first child seat in the left outboard seating
position using lower anchorages D and E. Install the
second child seat using the center anchorages, B and
C. Do not use the outer anchorage closest to the
opposite door, A. Do not use the remaining right
outboard seating position (1) for any occupant. The
center child restraint will block the seat belt buckle
for this position.
(fig. 145)
210
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

WARNING!
• UseanchoragesBandCtoinstalla
ISOFIX child

restraint in the center seat-
ing position (2). Do not install a ISOFIX child
restraint using anchorages C and D.This is not an
ISOFIX position in your vehicle.
• A child restraint installed in the center position
(2) will block the seat belt buckle for the empty
right outboard seating position (1). Do not use
this seat for another occupant .
• Never use the same lower anchorage to attach
more than one child restraint .
• If you are installing three child restraints next
to each other, you must use the seat belt and the
center tether anchor for the center position.You
can then use either the ISOFIX anchors or the
vehicle’s seat belt for installing the child seats in
the outboard positions. Please refer to “Installing
the ISOFIX Child Restraint System” for typical
installation instructions.
Always follow the directions of the child restraint
manufacturer when installing your child restraint. Not
all child restraint systems will be installed as described
here. To Install An ISOFIX Child Restraint:
1. If the selected seating position has a Switchable
Automatic Locking Retractor (ALR) seat belt, stow
the seat belt, following the instructions below. See
the section “Installing Child Restraints Using the
Vehicle Seat Belt” to check what type of seat belt
each seating position has.
2. Loosen the adjusters on the lower connectors and on the tether strap of the child seat so that you can
more easily attach the connectors to the vehicle
anchorages.
3. Place the child seat between the lower anchorages for that seating position. For some second row
seats, you may need to recline the seat and / or raise
the head restraint to get a better fit. If the rear seat
can be moved forward and rearward in the vehicle,
you may wish to move it to its rear-most position to
make room for the child seat. You may also move
the front seat forward to allow more room for the
car seat.
4. Attach the connectors of the child restraint to the lower anchorages in the selected seating position.
211
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Mode” description under “Occupant Restraints.” The
cinching latch plate is designed to hold the lap portion
of the seatbelt tight when webbing is pulled tight and
straight through a child restraint’s belt path.
Installing A Child Restraint With A Switchable
Automatic Locking Retractor (ALR)
1. Place the child seat in the center of the seatingposition. For some second row seats, you may need
to recline the seat and/or raise the head restraint to
get a better fit. If the rear seat can be moved
forward and rearward in the vehicle, you may wish
to move it to its rear-most position to make room
for the child seat. You may also move the front seat
forward to allow more room for the car seat.
2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child
restraint. Do not twist the belt webbing in the belt
path.
3. Slide the latch plate into the buckle until you hear a “click.”
4. Pull on the webbing to make the lap portion tight against the child seat.
5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt
webbing out of the retractor. Then, allow the web-
bing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This
means the seat belt is now in the Automatic Locking
mode.
6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any
webbing. If the retractor is notlocked, repeat
step 5.
7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you
push the child restraint rearward and downward
into the vehicle seat.
8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, con-
nect the tether strap to the anchorage and tighten
the tether strap. See the section “Installing Child
Restraints Using the Top Tether Anchorage” for
directions to attach a tether anchor.
9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt
path. It should not move more than 25 mm in any
direction.
Any seat belt system will loosen with time, so check
the belt occasionally, and pull it tight if necessary.
213
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

Installing A Child Restraint With A Cinching
Latch Plate (CINCH) — for versions/markets,
where provided
1. Place the child seat in the center of the seatingposition. For some second row seats, you may need
to recline the seat and / or raise the head restraint
to get a better fit. If the rear seat can be moved
forward and rearward in the vehicle, you may wish
to move it to its rear-most position to make room
for the child seat. You may also move the front seat
forward to allow more room for the car seat.
2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child
restraint. Do not twist the belt webbing in the belt
path.
3. Slide the latch plate into the buckle until you hear a “click.”
4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you
push the child restraint rearward and downward
into the vehicle seat.
5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, con-
nect the tether strap to the anchorage and tighten
the tether strap. Refer to “Installing Child Restraints Using The Top Tether Anchorage” for directions to
attach a tether anchor.
6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt
path. It should not move more than 25 mm in any
direction.
Any seat belt system will loosen with time, so check
the belt occasionally, and pull it tight if necessary.
If the buckle or the cinching latch plate is too close to
the belt path opening of the child restraint, you may
have trouble tightening the seat belt. If this happens,
disconnect the latch plate from the buckle and twist
the short buckle-end belt up to three full turns to
shorten it. Insert the latch plate into the buckle with
the release button facing out, away from the child
restraint. Repeat steps 4 to 6, above, to complete the
installation of the child restraint.
If the belt still cannot be tightened after you shorten
the buckle, disconnect the latch plate from the buckle,
turn the buckle around one half turn, and insert the
latch plate into the buckle again. If you still cannot make
the child restraint installation tight, try a different
seating position.
214
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS