2014 AUDI TT ROADSTER warning light

138 Child Saf ety
,8. WARNING
Not using a booster seat, using the boos­
ter seat improperly, incorrectly install ing a
booster seat or using the vehicle safety
belt improperly increases the risk of seri­
ous personal injury and death in a collision
or other eme rgency s ituation. To help re­
duce the risk of serious persona l injury
and/or death:
- T he shoulder belt must lie as close to the
center of the child· s collar bone as possi ­
ble and must lie and snug on the upper
body. It must never lie across the throat
or neck. The lap belt must lie across the
pelvis and never across the stomach or
abdomen . Make sure the belt lies flat
and snug . Pull on the belt to t ighten if
necessary .
- Failure to properly route safety belts over a ch ild's body will cause severe inju­
ries in an acc ident or other emergency
situation
¢ page 101 .
-Children on the front seat of any car,
even with Advanced A irbags, can be seri­
ous ly inju red or even killed when an a ir­
bag inflates.
- Never let a child stand or knee l on the
seat.
- Never let a child ride in the cargo a rea of
yo ur vehicle.
- Always remember that a ch ild lean ing
forward, sitting sideways or out of posi­
t ion in any way during an acc ident can be
struck by a deploying airbag. This will re­
sult in serious personal injury or death.
- If you must install a booster seat on the
front passenger seat because of excep­
tional circumstances the
PASSENGER
AIR BAG OFF
light must come on and
stay on, whenever the ignition is switch­
ed on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
¢page 119, Moni­
toring the Advanced Airbag System .
-If the PASSENGER AIR BAG OFF light
does not come on and stay on whenever
-
the ignition is switched on the inflating
airbag w ill hit the child safety seat or in­
fant carrier with great force and will smash the child safety seat and child
aga inst the backrest, door or roof. Have
the airbag system inspected immed iately
by your Audi dea ler.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
h icle is being used
¢page 101, Safety
belts,
¢ page 109, Airbag system and
¢ page 130, Important things to know .
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the front passenger can be
locked with the convertible locking retractor
to properly secure child safety seats.
T he safety belts emergency locking retracto rs
for the front passenger's seat safety belt have
a convertible locking retracto r for child re­
straints. The safety be lt must be locked so
that belt webbing cannot unreel. The retrac­
tor can be activated to lock the safety belt and
prevent the safety be lt webbing from loosen ­
ing up during normal driving. A child safety
seat can only be properly installed when the
safety belt is locked so that the child and child safety seat wi ll stay in place .
Always remember: Even though your vehicle is
equipped with an Advanced Airbag system, a
child should always ride in the seat properly
restrained for its age and s ize.
,8. WARNING
Imp roperly installed chi ld safety seats in­
crease the risk of serious personal injury
and death in a collision.
- Always ma ke sure that the safety belt re­
tractor is loc ked when insta lling a child
safety seat . An un locked safety belt re -
tractor cannot hold the child safety seat ..,_

in place during normal driving or in a
crash.
- Always buck le the child safety seat firmly
in place even if a child is not sitting in it.
A loose ch ild safety seat can fly around
dur ing a sudden stop or in a col lision
- The inflating a irbag w ill hit the child
safety seat or infant carrier w ith great
force and w ill smash the ch ild safety seat
and child against the backrest, door or
roof.
- Forward -fac ing ch ild safety seats or in ­
fant ca rr iers installed on the front pas­
senger 's seat may inte rfe re with the de­
ployment of the airbag and cause se rious
injury to the ch ild.
- Always read and heed all WARNINGS
whenever u sing a child rest rained in ave­
hicle is being used~
page 130 . Special
precautions apply when installing a ch ild
safety seat on the front passenger seat
~ page 110, Child restraints on the front
seat -some important things to know.
A WARNING
-
Always take special precautions if you
must install a forward or rearward-facing
child restraint on the front passenger's
seat in except ional situat ions :
- Whenever a forward or rearward-facing
child restraint is installed on the front
passenge r seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
~page 119, Moni­
toring the Advanced Airbag System.
- If the PA SSENGER AIR BAG OFF light
does not come on and s tay on whenever
the ignition is switched on the inflating airbag will hit the child safety seat or in­
fant carr ier with great force and wi ll
smash the ch ild safety seat and chi ld
against the backrest, door or roof. Have
the a irbag system inspected immediately
by your Audi dealer .
Child Safet y 139
-Improper installation of chi ld restraints
can reduce their effectiveness or even
prevent them from providing any protec­
tion .
- An improperly installed ch ild restra int
can interfere with the airbag as it de­ ploys and seriously injure or even k ill the
child.
- Always carefully follow the manufactur­
er 's instructions prov ided with the child
safety seat or carrier .
- Never p lace add itiona l items on the seat
that can increase the total weight reg is­
tered by the weight-sensing mat and can cause injury in a crash.
A WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacture r for use on a front seat
with a passenger fron t and s ide a irbag.
- Never put the fo rward-facing child re­
s traint up, against o r ve ry nea r the in­
strument panel.
- Always move the passenge r seat into its
rearmost pos ition in the seat's fore and
aft adj ustment range, as fa r away from
the airbag as possible before installing
the forward-fac ing ch ild restraint . The
backrest must be ad justed to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
li ght comes on and stays on all the
time whenever the ignit ion is switched
on.
A WARNING
Rearward -facing child restraints:
- A child in a rearward-facing child safety
seat insta lled on the front passenger
seat will be seriously in ju red and can be
killed if the front airbag inflates -even
with an Advanced A irbag System .
- The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smas h the child safety seat .,. •
•

140 Child Saf ety
and child against the backrest, door or
ro of.
- Always be especially careful if you mu st
ins tall a rearward facing c hild safety seat
on the front passenger seat in exception­
al circumstanc es.
- Make sure that the
PA SS ENGER AIR BAG
OFF
light comes on and stays on all the
t ime w henever the ignition is switched
on.
- Never install a rearward facing child
safety seat on the front passenger seat
unless the
PASSENGER AIR BAG OFF
light comes on and stays on. If the PAS·
SENGER AIR BAG OFF
light does not
come on and stay on h ave the airbag sys­
tem inspec ted immediately by your Aud i
dealer .
Activating the convertible locking
retractor
Use the convertible locking retractor to se­
cure a child restraint.
A lways heed the child sa fety seat man ufactur­
er's instructions when ins talling a chi ld re­
straint in your vehicle . To activate the conver ­
tib le locking retractor:
., Place the child restrain t on a seat .
., Slow ly pull the be lt
all the wa y out.
., Route it around or through the chi ld re ­
stra int be lt path
c:> ,&. .
., Push the child safety seat down with your
full weight to get the safety belt rea lly t ight.
., In sert the be lt tongue into the buckle fo r
t h at seating posi tion.
., Gu ide the safety be lt back into the retracto r
u nt il the belt lies flat a nd snug on the chi ld
sa fe ty seat.
., You should hear a "clicking" noise as the
belt winds bac k into the ine rtia reel. Test the
conve rtible locking retractor by pull ing on
the be lt . You should no longer be able to
pull the belt out of the retractor. The con­
vertib le lock ing retractor is now act ivated. .,
Ma ke s ure that the red release button is fac ­
ing away from the child rest raint so that it
can be unbuckled q uick ly .
., Pull on the belt to make sure the safety be lt
is properly tight and fastened so that the
seat ca nnot move forward or sideways more
t han one inch (2.5 cm) .
A WARNING
Using the wrong child res traint o r an i m­
pr operly ins talled chi ld restraint can cause
se rious pe rsonal injury or death in a crash.
- Always ma ke sure that the safety belt re-
trac to r i s lo cked when insta lling a child
safety seat . An un locked safety bel t re­
tracto r cannot hold the child safety seat
in place dur ing no rma l dr iving o r in a
crash.
- Always buckle the child safety seat firmly
in place even if a ch ild is not sitt ing in it.
A loose child safety seat can fly around
during a sudden stop or in a crash.
- Always make sure the seat backrest to
which the child restraint is installed is in
an upright pos ition. Otherw ise, the seat­
back with the ch ild safety seat attached
to it could fly forward in the event of an
accident o r othe r emergency situation.
- Always read and heed all WAR NIN GS
wheneve r using a child res trained in ave­
h icle is being used
c:> page 130. Special
p re ca utions apply when insta lling a child
safe ty se at on the fron t passenger seat
<=> page 110, Child restraints on the front
seat -some important things to know .
Deactivating the convertible locking
retractor
-
The convertible locking retractor for child re­
straints will be deactivated automatically when the belt is wound all the way back into
the retractor.
., Press the red b utton on the safety belt buck­
le . The belt tong ue will pop out of the b uck­
le .
., Guide the safety be lt all the way back into
its stowed position .

switched on all the time. In certain situations
when you need less traction, you can switch
off ESC by pressing the button
lru. Be sure to
switch ESC on again when you no longer need
less traction.
Anti-lock braking system (ABS)
ABS prevents the wheels from locking up
when braking . The vehicle can still be steered
even during hard braking . Apply steady pres ­
sure to the brake pedal. Do not pump the ped­
al. A pulsing in the brake pedal indicates that
the system is helping you to brake the vehicle.
Brake assist system
The brake assist system can decrease braking
d istance. It increases braking power when the
driver presses the brake pedal quickly in emer­
gency si tuations. You must press and hold the
brake pedal until the situation is over .
Anti-slip regulation (ASR)
ASR reduces engine power when the drive
wheels begin to spin and adapts the force to
the road condit ions. This makes it easier to
start, accelerate and drive up hills.
Electronic differential lock (EDL)
The EDL brakes wheels that are spinning and
transfers the drive power to the other drive
wheel or whee ls if the vehicle is equipped with
all-wheel drive*. This function is available up
to about 60 mph (100 km/h) .
In extreme cases, EDL automat ica lly switches
off to help keep the brake on the braked wheel
from overheating. EDL w ill switch on again au­
tomatically when conditions have returned to
normal.
..&, WARNING
- ESC, ABS, ASR and EDL cannot overcome
th e laws of physics. This is especially im ­
portant on slippery or wet roads.
If the
systems begin acting to stabilize your ve­
hicle, you should immediately change
your speed to match the road and traffic
condit ions. Do not let the increased safe­
ty provided by these systems tempt you
Intelligent technology 143
to take risks. Doing so will increase the
risk of a lo ss of vehicle control, co llision
and serious personal injuries.
- Always adapt your speed to road, traffic
and weather conditions. The risk of los­
ing control of the vehicle increases when
driving too fast, especially through
curves and on slippery or wet roads, and
when driving too close to vehicles up
ahead. ESC, ABS, the brake assist sys­
tem, EDL and ASR cannot prevent colli­
sions.
- Always accelerate with special care on
even, smooth surfaces such as those that
are wet or covered with ice and snow.
The drive wheels can spin even with
these assistance systems that cannot al ­
ways he lp to reduce the risk of loss of ve­
hicle control.
@ Tips
- ABS and ASR only work correct ly when
all four whee ls are equipped with identi­
cal tires. D ifferent tire si zes can lead to a
reduction in engine power.
- You may hear noises when the systems
described are working.
- If the ind icator lightD] orE (USA
models)/ [iJ (Canada models) appears,
there may be a malfunction¢
page 18,
¢ page 18.
Switching on and off
ESC turns on au tomatically when you start
the engine.
Fig . 123 Ce nter conso le: ESC OFF butto n

144 Intelligent technology
Switching ESC off (sport mode )
In certain situat ions, it m ight make sense to
allow some sl ip. For example :
- Rocking the vehicle to free it when it is stuck
- Driv ing in deep snow or on loose ground
- Driving with snow chains
Press the~ button . The ESC ind icator light
II
turns on and Stabilization prog ram off ap­
pears in the d isplay. ASR deactivates com­
p letely and the stabi lizat ion effects from the
ESC system are limited .
Switch ing on
Press the~ button again. The message Stabi­
li zation p rogram on
appears briefly in the dis­
p lay.
A WARNING
Only switch ESC sport mode on when your
driving abilities and the traffic s ituation
permit. Please note that the dr iv ing
wheels can spin and the vehicle can break a w ay in ESC sport mode, especia lly when
the road is slippe ry.
(D Tips
If the re are faults in the rea r spo ile r sys­
tem or in Audi magnet ic r ide, it may not be
possible to a ct ivate ESC spor t mode or
normal m ode may a ct ivate aga in a utomat­
ically.
Rear spoiler
A ppl ies to vehicles: with ret ractab le rear spoil er
The rear spoiler improves vehicle handling
and enhances driver control.
F ig. 124 Sw itch fo r rear spo ile r
The rear spoi le r deploys and retracts . Spoiler
operation can be set for a utomatic or man ua l
operation.
Automatic mode (normal operation )
-Automatic deployme nt: At a speed of about
75 mph (120 km/h), t he rear spo ile r deploys
automatically.
- Au tomatic retraction: When speed drops be­
low about SO mph (80 km/h), the rear spoil­
er retracts automat ica lly.
Manual mode
- Manual deployment: Tapp ing briefly on the
sw itch
¢fig. 124 deploys the rear spoiler.
- Manual retraction: At sp eeds up to about
10 mph ( 20 km/h), retract the rear spoiler
by pressing a nd ho ldi ng the sw itch
¢ fig . 124. At speeds be twee n 10 mph ( 20
km/h) a nd 75 mph ( 120 km/h), retract the
rear spoi ler by tapping on the switch
¢fig. 124.
A WARNING
-
Driving at higher speeds witho ut the rear
spoiler deployed ca n impair handling char­
acter istics, making the vehicle harder to
control.
- Always ma ke sure that the spo ile r is de­
p loyed when driving at speeds over
85 mph (140 km/h) .
If the rear spoiler
war ning/ indicato r light in the inst ru­
men t clu ster comes on, the rear sp oiler
may not have deployed.
- N ever d rive a t speeds h igher than
85 mph (140 km/h) i f the spoiler is no t
deploye d. Have the spoiler inspected as
soon as possible by an a uthorized Audi
deale r or q ualified workshop.
- Always obey speed limits and othe r tra f­
fic laws .
A WARNING
-Improper operation of the rear spoi ler can
cause crushing injuries.
- Always make sure that nobody, especially
chi ldren, is in t he way when the rear
spoiler is deployed or retracted.

146 Intellig ent technolog y
gear or lower driving range. Do no t ride
t h e brakes or hold the pedal down too
long or too often. This cou ld cause the
bra kes to get hot and dimin ish braking
efficiency .
- Do no t "ride the brakes" by resting your
foot on the pedal when you do not intend
to brake . Th is may cause the brakes to
overheat, prematu re wear and inc reased
stopp ing distan ce.
- Under certain climat ic and operating
c ondit ions such as passing through wa­
ter, driving i n heavy ra in or after wash ing
the vehicle, the effect iveness of the
brakes can be red uced . In winter, ice can
accumulate on the brake pads, linings,
discs and d rums . Carefully apply brakes
for a test . Brakes will dry and ice coat­
ings will be cleaned off after a few care­
ful brake applications.
- Driving for an extended period of time on
salt-covered roads w ithout us ing your
brakes can also affect braking efficiency .
Clean off accumulated salt coating from
brake d iscs and pads w it h a few cautious
brake appli cat ions.
- If you damage the fro nt spo iler, or if you
ins tall a different spoiler, be su re the air
flow to the fron t bra kes is not o bstr uct­
ed. O therwise the brake system co uld
overheat reducing the effectiveness of
the entire brake system.
- F ailure o f one bra ke c ircuit will impair
the b raking capability resulting in an in­
creased stopp ing distance . Avoid driv ing
the vehicle and have it towed to the near­
est Aud i dea le r o r qualified workshop.
- Never let the vehicle ro ll to a stop w ith
the engine shut off.
- If the brake booster is not working, t he
brake pedal must be pressed considera­
bly harder to make up for the lack of
booster assistance . Electro-mechanical
power assist
The electro-mechanical power assist helps
the driver when steering .
The degree of power assi st is electronically
matched to vehicle speed .
T he power steering system assists the driver
so that he can steer the vehicle with reduced
physical effor t.
Power steering will not work if t he engine is
off . As a result, the steering wheel will be hard
to turn.
A WARNING
If the system develops a problem , you
must seek qualified profess iona l assis ­
tance .
(D Note
-
If there is an e lectronic malfunction, ser­
votronic
will still function like a conven­
tiona l power steering system, providing a
constant steering support force that is no
l onge r proportionate to the vehicle speed .
This is most not icea ble whe n tu rni ng the
s tee ring w heel a t low speeds (fo r example
when pa rking), -more effort w ill be re­
q uired than us ua l.
- Be aware o f the diffe rent than usual
steering response and adjust your steer ­
ing force acco rdingly.
- Have the problem checked and set right
by an autho rize d Aud i dealer as soon as
possible.
- If a s teer ing mal func tion occurs, this is
signa led wit h the
,'Zr~ or .• indicato r
lights and a warning tone, see.
(D Tips
- If the powe r stee ring system sho uld fai l,
or if the engine is not ru nning (fo r exam­
ple, whi le being towed), you will still be
able to steer the vehicle. However, more
effort will be required to do so.
11-

Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
""Try and keep well below your car's maximum
speed.
Accelerating gently reduces fuel consump­
tion, engine wear, and does not disturb the
environment.
Fu el consumption, exhaust emissions and en ­
g ine noise increase disproportionately at high
speeds. If you drive at approximately three
quarters of top speed, fuel consumption will
be reduced by one half. Never drive faster
than the posted speed limit and weather con­
ditions permit .
Reducing unnecessary idling
Even when your car is just idling it burns up
fuel.
""Shut the engine off when you are not driving
the vehicle.
""Do not warm up the vehicle by letting the
engine run at idle .
It makes sense to shut
off the engine in traff ic
jams, when waiting for trains to pass at ra il­
road crossings, or at traffic lights that have
l ong wa its on red. Turning the engine
off for
just
30-40 seconds saves more fue l than is
burned starting the engine again .
It takes a long time for the engine to warm up
fully when it is running at idle. However, wear
and noxious emissions are especially high
when the engine is warming up. So you should
drive away as soon as you start the engine and
avoid running at high RPMs whi le the engine
is sti ll warming up .
(D Note
Do not leave engine idling unattended af­
ter starting . If warning lights should come
on to indicate improper operation, they
would go unheeded. Extended idling also
produces heat, which could result in over-
Driving and environment 153
'
heating or othe r damage to the vehicle or
other property.
Regular maintenance
A badly tuned engine unnecessarily wastes a
lot of fuel.
""H ave your veh icle serviced at regular inter-
vals.
By having your vehicle regu larly serviced by an
Audi dealer helps to ensu re that it runs prop­
erly and economically. The condition of your
vehicle not only affects its safety and ability to
hold its value, it also affects
fuel consump­
tion.
Check your oil each time you fill your tank.
The amount of o il used is related to engine
load and speed.
It is normal for the oil consumption of a new
engine to reach its lowest value after a certain
mileage has been driven.
You must drive your vehicle about 3,000 miles
(5,000 kilometres) before you can properly
assess oil consumpt ion.
This also app lies to fue l consumption and en­
gine output.
(U) Note
- Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
& Main­
tenance booklet. Lack of proper mainte­
nance as well as improper use of the ve­
hicle will impair the function of the
emission control system and could lead
to damage.
- Do not alter or remove any component of
the Emission Control System unless ap­
proved by the manufacturer.
- Do not alter or remove any device, such
as heat shields, switches, ignition wires,
valves, which are designed to protect
your vehicle's Emission Control System
and other important vehicle compo­
nents .
•
•

Vehicle care and clean ing
General information
Regular, proper care helps to maintain your
vehicle 's value. It can also be a requirement
when submitting warranty claims for corro ­
sion damage and paint defects on the body .
The required cleaning and care products can
be obtained from your authorized Audi dealer
or a qualified workshop . Read and follow the
instructions for use on the packaging.
A WARNING
-Us ing clean ing and care products incor­
rectly can be dangerous to your hea lth.
- Always store cleaning and care products
out of reach of children to reduce the risk
of poisoning.
@) For the sake of the environment
-Preferably use environmentally-friendly
products when buying cleaning agents.
- Do not d ispose of leftover cleaning and
care products with household trash .
Car washes
-
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the
vehicle, the more the surface can be dam­ aged. High temperatures such as those
caused by sunlight increase the corrosive ef­
fect.
Before washing, wet heavy deposits w ith plen­
ty of water.
Also, wash the underside of your vehicle once road salt stops be ing used for the season.
Pressure washers
When washing your vehicles with a pressure
washer, always follow the operating instruc­
tions provided w ith the pressure washer . Th is
is especially important in regard to the pres ­
sure and spraying distance. Do not aim the
spray directly at seals on side w indows, doors,
Vehicle care and cleaning 155
the hood, the rear lid or the convertible top or
at tires, rubber hoses, insulating material
orsensors*. Keep a distance of at least 16 in­
ches (40 cm) .
Do not remove snow and ice with a pressure
washer.
Never use rotary nozzles or high pressure noz­
zles.
The water temperature must not be above
140 °F (60 °C) .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows are closed and
the windshie ld wipers are off. Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes .
Washing by hand
Clean the veh icle starting from the top and
working down using a soft sponge or cleaning
brush. Use solvent-free cleaning products.
Washing vehicles with matte finish paint
by hand
To avoid damaging the paint when washing,
first remove dust and large particles from
your vehicle. Insects, grease spots and finger­
prints are best removed with a special cleaner
for matte finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use
too much pressure .
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft mi­
crofiber cloth.
Rinse the vehicle thoroughly again and let it
air dry . Remove any water residue using a
shammy.
Stubborn deposits such as bird droppings or
tree sap are best removed with p lenty of wa-
ter and a microfiber cloth. .,..
•
•