2014 AUDI TT COUPE check engine

Downloaded from www.Manualslib.com manuals search engine Checking
and topping up fluids
When it is discharged the battery can freeze
at temperatures around 0°
(.
- Make sure that the vapour hose is always at­
tached to the battery.
- Never use a damaged battery -risk of explo­
sion! Replace a damaged battery immedi­
ately.
- Never disconnect the car's battery with the
engine running or with the ignition turned
on, otherwise the electrical system or elec­
trical components will be damaged.
- Do not expose the battery to direct sunlight
over a Long period of time, as the intense ul­
traviolet radiation can affect the battery
housing.
- If the car is Left standing for Long periods,
protect the battery from frost. The battery
will be destroyed if it is allowed to freeze
¢page 228.
- When the doors are opened the windows
are automatically lowered by approximately
10 mm. This function is not available if the
battery is disconnected, and the door seal
and window may be damaged as a result.
Charging the battery
Terminals for charging the battery are fitted in
the engine compartment.
Fig. 216 Engine compartment: Terminals for jump leads
and battery charger
... Note the warnings ¢.&. in Important safety
warnings for handling a car battery on
page 227 and r=;, ,&..
... Switch off all electrical equipment and the igni­
tion.
228 ...
Open the bonnet ¢page 221.
... Open the red cap on the positive terminal
¢Fig. 216.
... Connect the charger cables as specified to the
jump-start terminals (terminal with red cap=
"positive", terminal with hexagon = "nega­
tive").
... Now connect the battery charger to the mains
and switch on .
... After
charging the battery: switch off the bat-
tery charger and disconnect the mains cable.
... Now disconnect the charger cables.
... Refit the red cap onto the positive terminal.
... Close the bonnet r=;,page 222.
When it is discharged the battery can freeze at
temperatures around 0°
C. You must not use a
battery which has frozen, even after it has
thawed, because the ice may have cracked the
battery casing and allowed the battery acid to es­
cape r=;,.&..
Charging the battery
Only use battery chargers with a maximum
charge voltage of 14.8 V (the battery cables do
not have to be disconnected). The battery must
not be opened while you are charging it.
Important: Before you charge the battery make
sure you read the manufacturer's instructions for
using the battery charger.
.&_ WARNING
Always replace a frozen battery. Never re­
charge it -risk of explosion!
{D Note
Use only the terminals in the engine compart­
ment to charge the battery.
Replacing the battery
Your vehicle is equipped with an intelligent pow-
er management system to control the distribu-
tion of electrical energy r=;, page 106. The power
management function ensures that the battery is
charged much more efficiently than on vehicles
without a power management system. For this
additional power to be available after replacing
.,.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D L/'l
N
L/'l
.... the
battery, we recommend that the replacement
battery used is of the same make and type as the
original-equipment battery. After changing the
battery, the power management system must be
initialised by a qualified workshop to ensure that
the replacement battery is charged to an opti­
mum level.
A replacement battery must have the same ca­
pacity, voltage (12 V) and current rating. It must
also have the same dimensions as the original,
factory-fitted battery and have sealed caps. The
battery must comply with the standards
TL 825 06 (dated April 2008 or later) and
VW 7 50 73 (April 2010 or later).
Since the battery is difficult to access, we recom­
mend having it replaced by an Audi dealer or
qualified workshop.
CD CAUTION
- Your vehicle is equipped with a special deep
cycle battery (e.g. AGM type). The on-board
electronic systems may develop problems if
you fit a different type of battery. For this
reason, if you need to replace the vehicle
battery, make sure that the specifications of
the new battery match the original exactly.
- Make sure that the vent hose is always at­
tached to the original opening on the side of
the battery. Gases or battery acid can other­
wise escape and possibly cause damage.
- The battery holder and clamps must always
be correctly secured.
- Before starting any work on the battery, al­
ways observe the warnings listed under
¢ page 227, Important safety warnings for
handling a car battery.
@ For the sake of the environment
"S Batteries contain toxic substances including
sulphuric acid and lead. They must be dis­
posed of appropriately and must not be put
together with ordinary household waste.
Make sure the battery removed from the vehi­
cle cannot tip over. Otherwise, sulphuric acid
could escape. Checking
and topping up fluids
Windscreen washer
N
N
co
al
Fig. 217 Engine compartment: Cap of windscreen washer
container
The container for the windscreen washer Q con­
tains the cleaning fluid for the windscreen and
the headlight washer system* ¢ Fig. 217,
¢page 222, Fig. 211. Container capacity
¢page 258.
Clean water should be used when topping up. If
possible, use soft water to prevent scaling on the
washer jets. Always add washer fluid to the water
(with anti-freeze additive in winter).
CD CAUTION
- Never put in radiator anti-freeze or other
additives.
- Never use washer fluid which contains paint
thinners or solvents as it can damage the
paintwork.
Service interval display
The service interval display detects when the
next service is due for your vehicle.
Fig. 218 Instrument cluster display: Service interval dis­
play (example)
There are two service interval display levels:
229

Downloaded from www.Manualslib.com manuals search engine Checking
and topping up fluids
- Inspection or oil change reminder: After acer­
tain mileage, a service reminder will appear on
the infotainment display each time the ignition
is switched on/off¢ Fig. 218. The distance or
time remaining will be shown briefly.
- Inspection or oil change due: When your vehi­
cle is due for an inspection, oil change or both,
the corresponding reminder Inspection due!,
Oil change due! or Oil change and inspection
due! will appear briefly after you switch the ig­
nition on/off.
Checking the service intervals
You can look up the distance and time remaining
until the next oil change and next service inspec­
tion. Select the following on the infotainment
system: I MENU I button > Car > left control button
> Se rvicing & checks > Service intervals. You can­
not check the service interval for the first 500 km
or so after resetting the display or when your ve­
hicle is new.
CD CAUTION
- Keeping to the correct service intervals is
most important for the service life and re­
sidual value of the vehicle (and especially
for the life of the engine). Services must al­
ways be carried out promptly, even if the
mileage is low.
- The time until the next oil change is not
counted down if the battery is disconnec­
ted. If your vehicle is out of service for an
extended period, please refer to the Service
Schedule for details of the next service
date.
230

Downloaded from www.Manualslib.com manuals search engine Wheels
and tyres
& WARNING
- Use only tyre/rim combinations and match­
ing wheel bolts approved by Audi. Otherwise
damage to the vehicle and an accident could
result.
- For technical reasons, it is not possible to
use wheels from other vehicles. In certain
cases, it is not even possible to use wheels
from another vehicle of the same model.
- It is very important to ensure that the tyres
you have chosen have adequate clearance.
When selecting replacement tyres, do not
rely entirely on the nominal tyre size marked
on the tyre; with some makes of tyre the ef­
fective tyre size can differ significantly from
the nominal dimensions, even though the
tyres have the same size designation. Inade­
quate tyre clearance can result in damage to
the tyres or the vehicle, causing a serious
safety risk.
- Avoid running the car on tyres that are more
than 6 years old. If you have no alternative,
you should drive slowly and with extra care
at all times.
- The use of run-flat tyres on your vehicle is
NOT authorised! Unauthorised use can cause
an accident or damage your vehicle.
- If wheel trims are fitted after the car is pur­
chased, ensure that there is an adequate
flow of air for cooling the brakes -risk of ac­
cident!
Tyre wear / damage
Fig. 219 Tyre tread: Tread wear indicators
l l
Please observe the applicable regulations in the country in
which you are travelling.
232 Tyre
wear
Inspect the tyres regularly for damage.
- The wear on under or over-inflated tyres is sig­
nificantly higher.
- Fast cornering, heavy acceleration and hard
braking all increase tyre wear.
- If you notice excessive tyre wear, have the
wheel alignment checked by a qualified work­
shop.
- Have your tyres rebalanced if steering wheel vi­
brations indicate an imbalance. Otherwise, the
tyres and other parts of the vehicle may wear
faster.
Tread wear indicators
The original tyres on your vehicle have 1.6 mm
high tread wear indicators ¢ Fig. 219 running
across the tread at regular intervals. The letters
"TWI" or triangles on the sidewall indicate the
positions of the tread wear indicators.
The minimum tread depth 1
) is reached at the lat­
est when the tread is worn down to the tread
wear indicators. Replace the tyres with new ones
¢ ,&..
Changing wheels round
Wheels should be changed round regularly to en­
sure that the wear is equal on all tyres. Fit the
wheels from the rear axle on the front axle and
vice-versa. All the tyres will then last for about
the same time.
On tyres with a directional tread pattern, note
the direction of rotation indicated on the sidewall
¢page 247.
Concealed damage
Damage to tyres and rims is often not readily visi­
ble. If you notice unusual vibrations or the car
pulling to one side, this may indicate that one of
the tyres is damaged. Reduce your speed imme­
diately. Inspect the tyres for damage. If no exter­
nal damage is visible, drive slowly and carefully
to the nearest qualified workshop and have the
car inspected.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
,-j
\D L/'l
N
L/'l
,-j A
WARNING
Insufficient tread depth or different tread
depths on different wheels reduce safety. This
is particularly evident in vehicle handling,
when there is a risk of aquaplaning in deep
puddles of water and when driving through
corners. Braking is also adversely affected -
risk of accident!
Tyre pressure
Audi V V
Fig. 220 End face of driver's door: Sticker listing the tyre
pressures
The correct inflation pressures for tyres fitted at
the factory and for the compact temporary spare
wheel* are specified on a sticker. The sticker
¢ Fig. 220 is on the end face of the driver's door.
@ Tyre size
@ Tyre pressure for the front wheels
© Tyre pressure for the rear wheels
(D Tyre pressure if vehicle is partially loaded
@ Tyre pressure if vehicle is fully loaded
@ Tyre pressure for the compact temporary
spare wheel*
If you intend to drive the vehicle with a partial
load, adjust the tyre pressures to the specified
setting (D. Should you wish to drive with a full
load, you must increase the tyre pressure to the
specified maximum @
¢.&,.
.
Checking / adjusting the tyre pressures
.. Check
the tyre pressures at least once a month
and, in addition, before starting a long journey. Wheels
and tyres
.. The tyre pressures should only be checked when
the tyres are cold. The slightly raised pressures
of warm tyres must not be reduced.
.. Refer to the sticker ¢ Fig. 220 for the correct
tyre pressures according to the load the vehicle
is carrying.
.. If necessary , adjust the tyre pressure.
.. Vehicles with tyre pressure loss indicator*:
Store the new tyre pressures on the infotain­
ment system ¢ page 235 .
.. Check the pressure of the spare wheel* /com­
pact temporary spare wheel*. Keep the spare
tyre inflated to the highest pressure approved
for the tyre.
A WARNING
Always adjust the tyre pressures to match
your driving style and the load the vehicle is
carrying.
- Excessive loads can cause you to lose control
of the vehicle -risk of accident!
- Under-inflated tyres flex more and can over­
heat at high speeds or when the vehicle is
carrying a heavy load. This could cause a
tyre blow-out and you could lose control of
the vehicle -risk of accident!
- Incorrect tyre pressures increase tyre wear
and adversely affect vehicle braking and
handling -risk of accident!
CD CAUTION
Replace any lost valve caps to prevent dam­
age to the tyre valves.
@ For the sake of the environment
Under-inflated tyres will increase the fuel con­
sumption.
@ Note
We recommend using the tyre pressure set­
ting (Dor@ for partial loads.
Winter tyres
In winter road conditions winter tyres will consid­
erably improve the car's handling. Due to their
type of construction (width, rubber compound,
IJII>
233

Downloaded from www.Manualslib.com manuals search engine Wheels
and tyres
tread pattern), summer tyres give less grip on ice
and snow.
... Winter tyres must be fitted on all four wheels.
... Only use winter tyres of the correct type ap-
proved for your vehicle.
... Please
note that the maximum permissible
speed for winter tyres may be lower than for
summer tyres¢.&_ . Your specialist retailer can
advise you of the maximum speed for your
tyres.
... After fitting the wheels you must always check
the tyre pressures ¢page 233.
Winter tyres lose their effectiveness when the
tread is worn down to a depth of 4 mm. The per­
formance of winter tyres is also severely impaired
by ageing, even if the tread is still much deeper
than 4 mm.
.&_ WARNING
- Never exceed the maximum approved speed
for your tyres. This causes the tyres to over­
heat and can even result in a blow-out -risk
of accident!
- Always adapt your driving style to the pre­
vailing road and traffic conditions. Drive
carefully and reduce your speed on icy or
slippery roads. Even winter tyres lose their
grip on black ice.
@) For the sake of the environment
Summer tyres should be fitted again as soon
as possible; they give better handling on
roads which are free of snow and ice. They are
quieter, do not wear so quickly and reduce
fuel consumption.
(Qj) Note
All-weather tyres can also be used instead of
winter tyres. Please note that winter tyres
with the & symbol are required by law during
the winter season in some countries.
Snow chains
Snow chains will improve braking ability as well
as traction in winter conditions.
234 ...
Snow chains can be used on the front wheels
only. This also applies to vehicles with four­
wheel drive* .
... Check that the snow chains are correctly seated
after driving for a few yards; follow the instruc­
tions given by the manufacturer .
... Keep your speed below 50 km/h. Please ob-
serve the applicable local regulations.
For technical reasons snow chains may only be
used on tyres with certain wheel rim/tyre combi­
nations.
Rim size
Rim offset Tyre
size
7Jx17 47mm 225/50
Only use snow chains with fine-pitch links. The
links must not protrude more than 13.5 mm
from the tyres (including tensioner).
You must remove the snow chains on roads which
are free of snow; otherwise the vehicle handling
may be impaired and the tyres may be damaged.
.&_ WARNING
Unsuitable or incorrectly mounted snow
chains can cause you to lose control of the ve­
hicle -risk of accident!
CD CAUTION
Snow chains can damage the rim/hubcap* if
they make direct contact with it. Remove the
hubcaps* beforehand. Use snow chains which
have a protective coating.
Tyre pressure Loss
indicator
Tyre pressure loss indicator in instrument
cluster
Applies to vehicles: with tyre pressure Loss indicator
The tyre pressure Loss indicator in the instrument
cluster informs the driver if the tyre pressure is
too low or a system malfunction has occurred.
The tyre pressure loss indicator makes use of the
ABS sensors to compare the rolling circumfer­
ence and the vibration of the tyres. If changes in
the inflation pressure are detected on one or
more tyres, the driver is alerted by an indicator
..,.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... lamp
[Bl and a message on the infotainment dis­
play. If only one tyre is affected, the display will
indicate its position.
Each time you change a tyre, change the wheels
round or change the tyre pressures on your vehi­
cle (e.g. when switching from partial load to full
load and vice-versa), you must store the new tyre
pressures on the infotainment system
¢ page 235. Monitoring of the tyre pressures is
based on the tyre pressures you have stored. The
inflation pressures recommended for your vehicle
are given on the tyre pressure sticker
¢ page 233, Fig. 220.
The rolling circumference and vibration can
change and cause a tyre pressure warning if:
- The inflation pressure in one or more tyres is
too low.
- The tyre has suffered structural damage.
- The wheels were changed or the tyre pressures
were changed and the new tyre pressures were
not stored ¢ page 235.
- You are driving with the temporary spare
wheel*.
Indicator lamps
RI]- Loss of pressure on one or more tyres¢ A.
Check and change or repair the tyre(s). Check and
adjust the inflation pressures of all four tyres
again and store the new tyre pressures on the in­
fotainment system¢ page 235.
ffim (Tyre Pressure Monitoring System) Tyre
pressure: fault. See owner's manual -If� ap­
pears and the indicator lamp [Bl in the instru­
ment cluster display flashes for approx. one mi­
nute and then remains lit after you have switched
on the ignition or while you are driving, there is a
fault in the system. Try to store the correct tyre
pressures ¢ page 235. If the indicator lamp
does not go out or if it comes on again after a
short time, drive to a qualified workshop without
delay and have the fault rectified.
&_ WARNING
- If the tyre pressure loss indicator appears
on the display, slow down immediately and
avoid any severe braking or steering ma- Wheels
and tyres
noe uvres. As soon as you can do so safely,
stop and check the tyres and the tyre pres­
sures.
- It is the driver's responsibility to ensure that
the tyre pressures are correct. For this rea­
son you must check the tyre pressures regu­
larly.
- Under certain conditions (e.g. driving at
high speeds, on ice and snow or on poor
road surfaces) the tyre pressure loss indica­
tor may not appear immediately.
- Run-flat tyres* may only be used on vehicles
which were originally equipped with this
type of tyre.
- If a malfunction occurs in the ESC system,
the tyre pressure loss indicator may also be
out of action.
- When driving with snow chains, a system
malfunction can occur.
- The tyre pressure loss indicator on your Audi
is specially matched to tyres with the mark­
ing "AO" or "RO" ¢ page 231. We recom­
mend that you use these tyres.
Storing tyre pressure settings
Applies to vehicles: with tyre pressure loss indicator
When you change a tyre or the tyre pressure on
your vehicle, you must confirm the change on the
infotainment system.
� Before storing the new tyre pressures, check
that the current pressures on all four wheels
correspond to the specified values and adapt
the pressures to the current load ¢ page 232.
� Switch on the ignition.
� Select the
following on the infotainment sys­
tem: I MENU I button >Car> left control button
> Servicing & checks > Tyre pressure loss indi­
cator.
@ Note
Do not store the tyre pressures if you are driv­
ing with snow chains. Otherwise, a system
malfunction may occur .
235

Downloaded from www.Manualslib.com manuals search engine 0
N
co
,-j
\D L/'l
N
L/'l
,-j Mobility
General notes
... If your vehicle experiences technical problems,
stop the car well away from moving traffic. If
you have a flat tyre, you should park the car on
a level surface. Be particularly careful if you are
on a slope .
... Apply the parking brake .
... Switch the hazard warning lights on .
... Place the warning triangle in a visible location
¢page 241.
... Instruct all passengers to leave the car when it
is safe to do so. They should wait in a safe place
(for instance behind the roadside crash barrier).
A WARNING
You should note the procedure described
above for your own safety and that of other
road users.
Equipment Warning triangle
Applies to vehicles: with warning triangle
Fig. 221 Luggage compartment: Warning triangle
The factory-supplied warning triangle is stowed
in the luggage compartment.
The luggage compartment is specifically de­
signed to hold only the warning triangle supplied
as an Audi Genuine Accessory. Mobility
First-aid kit
Applies to vehicles: with first-aid kit
Fig. 222 Rear seats: Compartment for first-aid kit
The first-aid kit is located in a compartment next
to the right side rear seat.
Fire extinguisher
Applies to vehicles: with fire extinguisher
The factory-fitted fire extinguisher is located in
the footwell on the front passenger's side (se­
cured in a holder).
... Remove the fire extinguisher by pressing on the
tab marked "PRESS".
... To secure the fire extinguisher, put it in the
holder and fasten the securing belt.
Check how the fire extinguisher works before you
need to use it. The instructions for use are shown
on the fire extinguisher.
A WARNING
If the fire extinguisher is not secured properly
it could be catapulted through the vehicle
during driving and braking manoeuvres or in
the event of an accident. This poses a risk of
injur y to occupants.
� Note
The fire extinguisher must comply with legal
requirements. Observe the expiry date of the
fire extinguisher.
241