2014 AUDI TT COUPE warning

Downloaded from www.Manualslib.com manuals search engine Instruments
and warning/indicator lamps
hold the vehicle. The brakes have overheated. The
vehicle can roll away, even on a gentle slope.
• Press brake pedal to release parking brake
To release the parking brake, press the brake ped­
al and simultaneously press the switch � (alter­
natively, use the auto release function
¢ page 67, Driving away from a standstill).
l'iJ Parking brake: fault. See owner's manual
There is a malfunction in the parking brake. Drive
to a qualified workshop without delay and have
the fault rectified.
l!J Parking brake: fault. Safely stop vehicle.
Please contact workshop
There is a malfunction in the parking brake. Drive
to a qualified workshop soon and have the fault
rectified.
[i] Hold assist: only available when door is
closed and engine is running
If this message appears, make sure that the door
is closed, the seat belt is buckled and the engine
is running.
[i] Hold assist: unavailable
If this message appears, the system require­
ments have not been met.
[§] Please release parking brake
If this message appears, release the parking
brake.
[§] Parking brake auto release: unavailable
If this message appears, press the brake pedal
and then release the parking brake.
[§] Parking brake: caution! Vehicle parked too
steep
If the warning lamp flashes and the message ap­
pears, the brake may not be strong enough to
hold the vehicle. The brakes have overheated. The
vehicle can roll away, even on a gentle slope.
[§] Parking brake is applied
If this message appears, press the brake pedal
and then release the parking brake as necessary .
12 Note
For further information on the parking brake
refer to ¢ page 66.
-L /? Cooling system
• Switch off engine and check coolant level
The coolant level is too low.
Switch off the engine and do not drive on. Check
the coolant level¢ page 224.
- If the coolant level is too low, add more coolant
¢ page 225. Do not drive on until the warning
lamp has gone out.
- If the coolant level is correct, the overheating
may be caused by a malfunction of the radiator
fan. Do not drive on. Obtain professional assis­
tance.
• Coolant temperature: too high. Let engine
run with vehicle stationary
Let the engine cool down by running it at idling
speed for a few minutes.
A WARNING
- Never open the bonnet if you can see or hear
steam or coolant escaping from the engine
compartment; there is a risk of being scal­
ded. Wait until you can no longer see or
hear escaping steam or coolant.
- The engine compartment of any motor vehi­
cle is a dangerous place. Before carrying out
any work in the engine compartment,
switch off the engine and allow it to cool
down. Please observe the important safety
warnings ¢ page 220, Working on compo­
nents in the engine compartment.
CD CAUTION
Do not drive on if the warning lamp. lights
up; other wise there is a risk of engine dam­
age.
� Engine oil pressure
• Switch off engine. Oil pressure too low

Downloaded from www.Manualslib.com manuals search engine Instruments
and warning/indicator lamps
Switch off the engine and do not drive on. Check
the engine oil level ¢ page 22 3.
- If the engine oil level is too low, add more oil
¢ page 224. Do not drive on until the warning
lamp has gone out.
-If the engine oil level is OK and the warning
lamp is flashing, switch off the engine and do
not drive on. Obtain professional assistance.
(I}) Note
The oil pressure warning lamp is not an indi­
cator for the oil level. The oil level should
therefore be checked regularly.
0 Alternator / battery
• Electrical system: fault. Battery is not being
charged.
There is an alternator fault or a fault in the vehi­
cle's electrical system.
Drive to a qualified workshop without delay.
Avoid using electrical equipment that is not abso­
lutely necessary (such as the radio) because this
will drain the battery . If the battery charge is in­
sufficient, obtain professional assistance.
(•] Electrical
system: low battery charge. Please
activate drive system
Starting reliability may be impaired.
If this message disappears after a while, the bat­
tery will have been sufficiently charged while
driving.
If the message does not disappear again, drive to
a qualified workshop without delay and have the
fault rectified.
� Front seat belt
The warning lamp.
lights up and does not go
out until the driver's and front passenger's* seat
belts have been fastened. When the vehicle has
gathered speed you will also hear a warning
� chime.
co ....
\D L/'l
N
L/'l
.... (D)
Note
For further information on the seat belts
¢page 204.
�- Steering lock
• Steering: fault. Please stop vehicle
There is a malfunction in the electronic steering
lock. The ignition can no longer be switched on.
Do not have the vehicle towed away, because you
won't be able to steer it. Obtain professional as­
sistance.
,�. e Steering
lock: fault. Please contact work­
shop
There is a malfunction in the electronic steering
lock.
Drive to a qualified workshop soon and have the
fault rectified.
,&. WARNING
Your vehicle must not be towed if there is a
fault in the electronic steering lock -risk of
accident!
L'.h Central warning/indicator lamp
If the warning lamp.
or indicator lamp II
lights up, note the information in the instrument
cluster.
© - Engine start system
• Engine start system: fault. Please contact
workshop
Do not switch off the ignition; otherwise you may
not be able to switch it on again.
Drive to a qualified workshop without delay and
have the fault rectified.
Ill Engine start system: fault. Please contact
workshop
There i
is
a malfunction in the engine start system.
Drive to a qualified workshop soon and have the
fault rectified.
13

Downloaded from www.Manualslib.com manuals search engine Instruments
and warning/indicator lamps
f}/D Electronic stabilisation control (ESC)
and (@)) anti-lock brake system
If the indicator lamp II flashes while the vehicle
is in motion, the ESC or traction control system
(ASR) is intervening.
If the indicator lamp II lights up, the ES( sys­
tem has been switched off for system reasons. In
this case, the ES( can be reactivated by switching
the ignition off and then on again. If the indica­
tor lamp goes out, this means the system is fully
functional.
Stabilisation control (ESC): sport. Warning! Re­
stricted stability
If the indicator lamp fil lights up, the ESC sport
mode has been activated via the I� OFFi
button
¢page 104. You can switch the ESC system back
on by
pressing the I� OFFi
button again.
Stabilisation control (ESC): switched off. Warn­
ing! Restricted stability
If the indicator lamp II lights up, the ESC sys­
tem has been partially or completely switched off
via the I� OFFi button ¢ page 104. In addition,
ESC OFF will appear. You can switch the ESC sys­
tem back on by pressing the I� OFFi button
again.
The system is activated when you switch on the
ignition. If the indicator lamp II goes out, this
means the system is fully functional.
Stabilisation control (ESC): fault! See owner's
manual
Stabilisation control (ESC/ABS): fault! See own­
er's manual
ABS: fault! See owner's manual
If the indicator lamp II and the ABS indicator
lamp [i] light up and the message appears, there
is a malfunction in the anti-lock brake system or
electronic differential lock. This will also cause an
ESC malfunction. The vehicle can still be braked
in the normal way (however the ABS control func­
tion will be out of action).
Drive to a qualified workshop without delay and
have the fault rectified.
14 A
WARNING
If the brake warning lamp. lights up to­
gether with the ABS indicator lamp and the
ESC indicator lamp, this can mean that the
control function of the ESC/ ABS is not work­
ing. Input from the functions that stabilise
the vehicle is no longer available. This could
cause the vehicle to skid sideways. Drive care­
fully to the nearest qualified workshop and
have the fault rectified.
(t} Note
For more information about the ESC and ABS
systems, refer to ¢ page 102.
(0) Brake pads
II] Brake pads: wear limit reached. You can con­
tinue driving. Please contact workshop
The brake pads are worn.
Drive to a qualified workshop without delay and
have the brake pads checked.
!t Safety systems
The indicator lamp El monitors the safety sys­
tems and the pedestrian protection system.
Safety system
If the indicator lamp fll lights up or flashes,
there is a malfunction in one of the safety sys­
tems.
Drive to a qualified workshop without delay and
have the fault rectified.
Pedestrian protection system
If the indicator lamp m lights up or flashes and
the bonnet is in a raised position, the pedestrian
protection system has been triggered. Please re­
fer to ¢ page 202, Pedestrian protection sys­
tem.
A WARNING
Have the safety systems examined without
delay; otherwise they may fail to trigger in an
..,.

Downloaded from www.Manualslib.com manuals search engine Instruments
and warning/indicator lamps
accident -this could result in serious or possi­
bly fatal injury.
rd.::, Engine management
Applies to vehicles: with petrol engine
If the indicator lamp II lights up, there is a fault
in the engine management system.
Drive slowly to a qualified workshop without de­
lay and have the engine checked.
W Engine management (diesel engine)
Applies to vehicles: with diesel engine
If the indicator lamp II lights up when the igni­
tion is switched on, the glow plugs are preheat­
ing.
If the indicator lamp flashes while the vehicle is
moving, there is a fault in the engine manage­
ment system.
Drive slowly to a qualified workshop without de­
lay and have the fault rectified.
o Emission control system
If the indicator lamp II lights up or flashes, a
fault has occurred which can reduce the quality of
the exhaust gas and damage the catalytic con­
verter.
Drive slowly to a qualified workshop without de­
lay and have the fault rectified.
,. Diesel particulate filter
Applies to vehicles: with diesel engine and diesel particulate
filter
C Particulate filter: fault. See owner's manual
The diesel particulate filter requires regenera­
tion. You can assist the self-cleaning function of
the filter by driving as follows:
Drive at a speed of at least 60 km/h for about
15 minutes in 4th or 5th gear, or with the selec­
tor lever in position S on vehicles with automatic
"' gearbox. Keep the engine speed at about
� 2000
rpm. As a result of the increase in tempera-
....
ID ture, the soot in the filter will be burned off. The
Lfl
N
Lfl
.... indicator
lamp will go out once the cleaning proc­
ess has been completed successfully.
If the indicator lamp does not go out, drive to a
qualified workshop without delay and have the
fault rectified.
A WARNING
It is essential that you adjust your speed to
suit the weather, road, terrain and traffic con­
ditions. The recommended driving speed
must never lead to the driver disregarding the
traffic regulations.
For more information about the diesel partic­
ulate filter, refer to¢ page 220.
!?\ Engine speed governing
Applies to vehicles: with engine speed governing
la Max. engine speed XXXX rpm
The engine speed will automatically be governed
to the speed displayed in the driver information
system. This protects the engine from overheat­
ing.
The rev limiter is deactivated as soon as the en­
gine temperature is no longer within the critical
range and you have taken your foot off the accel­
erator.
If the rev limiter has been activated because of a
fault in the engine management system, the indi­
cator lamp� will also light up. Make sure that
the engine speed does not exceed the speed dis­
played in the driver information system, for ex­
ample when shifting down a gear. Drive to a
qualified workshop without delay and have the
fault rectified.
�- Engine oil level (min.)
E!! Please check oil level
You can continue driving for the time being but
you should check the engine oil level as soon as
possible ¢page 223.
- If the engine oil level is too low, add more oil
¢page 224. 1JJJ.
15

Downloaded from www.Manualslib.com manuals search engine Instruments
and warning/indicator lamps
- If the engine oil level is normal but the indica­
tor lamp stays on, drive to a qualified workshop
without delay and avoid high engine speeds.
-e:r ..,. Engine oil sensor
l!I Oil level sensor system: fault. Please contact
workshop
The sensor for checking the engine oil level has
failed. Drive to a qualified workshop soon and
have the fau Lt rectified.
Bu Fuel tank system (petrol/diesel)
Applies to vehicles: with petrol or diesel engine, without nat­
ural gas engine
GD Please refuel
When the indicator lamp lights up for the first
time and the message appears, there are still
about 7 litres of fuel left in the tank.
GD Please refuel immediately
If the indicator lamp lights up and the message
appears , the fuel tank is almost empty. Drive to a
filling station without delay.
GD Tank system malfunction! Please contact
workshop
If the indicator lamp lights up and the message
appears:
- there is a malfunction in the tank system, or
- on vehicles with a diesel engine, water may
have collected in the fuel filter.
Drive to a qualified workshop without delay and
have the fau Lt rectified.
CD CAUTION
Applies to vehicles with diesel engine: If poor­
quality diesel fuel is used, it may be necessary
to have the water separator 1
>
on the fuel fil­
ter drained more frequently than is specified
in the Service Schedule. This helps to prevent
potential engine faults.
l l
This function is not available on all export versions.
16 (®
For the sake of the environment
Never pour fuel down drains or into the
ground.
(CD) Note
For more information about filling the tank,
refer to¢ page 218.
• Washer fluid level
C Please add washer fluid
With the ignition switched off, top up the fluid
for the winds creen washer and headlight washer
system* ¢ page 229.
'V! Winds creen wipers
B] Windscreen
wipers: fault. Please contact
workshop
There is a malfunction in the windscreen wipers.
Drive to a qualified workshop without delay and
have the fault rectified.
-:cp:- Bulb monitor
If the indicator lamp II lights up, a bulb has
failed. The message indicates the location of the
bulb.
You should have the bulb replaced without delay.
Vehicle lights: fault. Please contact workshop
There is a fault with the headlights or light
switch. Drive to a qualified workshop soon and
have the fault rectified.
_& WARNING
- Bulbs are sensitive to pressure. The glass
can break when you touch the bulb, causing
injury.
- Incorrect handling of the high-voltage ele­
ment of xenon gas-discharge bulbs* can
have potentially fatal consequences.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D L/'l
N
L/'l
.... Instruments
and warning/indicator lamps
i,(D Headlight range control
II Headlight range control: fault. See owner's
manual
There is a malfunction in the headlight range
control which may cause other road users to be
dazzled.
Drive to a qualified workshop without delay and
have the fault rectified.
§§0 Audi adaptive light
Applies to vehicles: with Audi adaptive light
Ill Audi adaptive light: fault. See owner's man­
ual
There is a malfunction in the adaptive light. The
dipped beam headlights will still be working nor­
mally.
Drive to a qualified workshop soon and have the
fault rectified.
fi. o Light sensor/ rain sensor
Applies to vehicles: with light sensor/ rain sensor
El Automatic headlights: fault. See owner's
manual
El Automatic wipers: fault. See owner's man­
ual
The light sensor/rain sensor is out of action.
For safety reasons, the dipped beam headlights
will then be switched on permanently when the
light switch is set to the AUTO position. You can
still switch the lights on and off in the normal
way with the light switch. You can also continue
to use all the other wiper functions that do not
use the rain sensor.
Drive to a qualified workshop soon and have the
fault rectified.
Q Suspension control
Applies to vehicles: with Audi drive select
I) Suspension: fault. You can continue driving
There is a malfunction in the suspension control
system. Drive
to a qualified workshop without delay and
have the fault rectified.
¢ ¢ Turn signals and hazard warning
lights
If the indicator lamp.
or.
flashes, the turn
signals are on. If both indicator lamps flash, the
hazard warning lights are on.
If one of the indicator lamps flashes twice as fast
as usual, a turn signal bulb has failed. You should
have the bulb replaced without delay.
Of� Rear seat belt
Applies to vehicles: with seat belt warning system (rear)
The warning lamp 111,tfil lights up briefly when
the ignition is switched on.
If a rear seat belt is buckled/unbuckled, the cor­
responding indicator lamp lights up briefly.
H- If the indicator lamp lights up briefly, the
corresponding rear seat is not occupied or the
seat belt is not buckled. If the seat belt is un­
buckled while the vehicle is moving, you will also
hear a warning tone.
ill- If the indicator lamp lights up briefly, the
seat belt has been fastened.
@ Note
For further information on the seat belts
c::>page204.
17

Downloaded from www.Manualslib.com manuals search engine Driver
information system
Driver information system
Overview
Fig. 4 Driver information system: Classic view
Fig. 5 Driver information system: Extended view
Th e driver information system displays various
comp onents:
(D Rev counter
@ Secondary display on left (two separate sec-
tions in extended view)
@ Tab area
@ Central area
® Status line (displayed on one or two lines)
® Secondary display on right (two separate sec­
tions in extended view)
(J) Speedometer
A WARNING
Do not rely on the outside temperature dis­
play as an ice warning. Bear in mind that
18 there
may be patches of ice on the roads even
at outside temperatures around +5 ·c -risk of
accident!
(CD) Note
- You can change the measurement units for
temperature or speed, etc. via the infotain­
ment system.
- When the vehicle is stationary or travelling
at very low speeds, the temperature dis­
played may be slightly higher than the ac­
tual outside temperature as a result of the
heat radiated from the engine.
- At temperatures below +5°
C a snowflake
symbol appears next to the temperature
display ¢&..

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... Multi-function steering
wheel with arrow
buttons
How to use the multi-function steering
wheel
You can use the multi-function steering wheel to
control the driver information system and MMI
functions, adjust the volume and switch the
speech dialogue system* on
/o
ff.
Fig. 6 Infotainment display view
Fig. 7 How to use multi-function steering wheel
Important: The ignition must be switched on.
Q) !<11>! button
- To switch between tabs: Press the left/right
side of the !<11>! button (e.g. to call up radio
functions).
The driver information system shows information
@ in several display tabs@.
The equipment installed on your vehicle deter­
mines which of the following tabs are available:
1st tab Vehicle
2nd taba) Warnings
3rd tab Radio ¢page 163
Media ¢page 168 Driver
information system
4th tab Telephone*
¢ page 123
5th tab Navigation* ¢ page 147
Map*
6th tabb)
Sound¢ page 186
Audi connect ¢ page 137
Settings
al This tab is only visible if one or more warning/indicator
lamps or driver messages are displayed or if the relevant
system is switched on.
b l
The tab contents depend on which menu you used last.
@ !VIEW!
button
- To change views: Press the !VIEW! button to
switch from the classic view ¢page 18, Fig. 4
to the extended view¢ page 18, Fig. 5.
@� button
- To return to the previous function level: Press
the� button.
@ Control buttons
- To call up the selection menu: Press the left
control button.
- To call up the options menu: Press the right
control button.
® Left thumbwheel
- To select a function: Scroll the left thumbwheel
to the desired function in a menu or list (e.g. to
select a radio station).
- To confirm your selection: Press the left
thumbwheel (e.g. to tune to the radio station).
19