32 Opening and clo sing
@ Tips
- The remote control key is automatica lly
deactivated when the ignition is sw itch
ed on.
- The operation of the remote contro l key
can be temporarily disrupted by interfer
ence from transmitters in the vicinity of
the vehicle work ing in the same frequen
cy range (e.g. a cell phone, radio equip
ment) .
- In order to make sure the locking func
tion is working, you shou ld always keep
you r eye on the vehicle to make sure it is
proper ly locked.
- Do not use the remote control if you are
i ns ide the car, otherwise you may unin
tentiona lly lock the vehi cle, and then you
would set off the anti-theft alarm when
you try to start the engine or open a
door . In case this happens anyhow, push
the un lock button @.
- Use the panic funct ion only if you are in
an emergency situation.
Resetting the remote control
The remote control must be reset if the vehi
cle does not unlock .
• Pres s the unlock button ffi on the remo te
control.
• Manua lly unlock the drive r's door lock with
the mechanical key within 30 seconds.
• Press e ither the lock-
ffi or the unlock @ but
ton to complete the reset sequence.
Operating locks with the key
To lock and unlock the vehicle from the out
side, turn the key in the lock of the driver's
door.
F ig . 24 Key turns for opening and dosing
• To unlock the vehicle, turn the key to the
opening position@¢
fig. 24 .
• To lock the vehicle, tu rn the key in the lock
of the driver's door to the lock pos ition @
¢ .&.-
A WARNING
=
Always read and heed WARNING¢.&. in
General description on page 30 .
Locking and unlocking the vehicle from
inside
The vehicle can be locked or unlocked from
the inside using the power locking switch .
Fig . 25 Sect ion fro m driver's door: Power locking
switc h
• Press the upper part of the power lock ing
sw itch@ to lock the vehicle ¢_&. .
• Press lower pa rt of the switch
al to unlock
t he vehicle.
-
If you lock the vehicle using the power locking
switch, please note the fol lowing :
- You canno t open the doors from the
ou tside
(in cre ased sec urity, fo r example when you
are stopped at a red light) .
- The L ED in the swi tch ~ ligh ts up when all
the doors and the front lid are closed and
locked.
- You can unlock and open the doors from the
i nside by pull ing o n the doo r hand le.
- You canno t lock the vehicle wi th the centr al
locking switch when the driver's door is
open .
-If you have a crash and the a irbag is acti va t
ed, the doors au tomati cally un lock .
_& WARNING
-If you use the powe r locking switch with
the doors closed , remember that a ll the
vehicle doors will lock.
- Locked doors make it more diffic ult for
emergency workers to get into the vehi
cle, which p uts lives at r isk. Do not leave
anyone beh ind in the vehicle, especially
c h ildren.
Emergency locking
If the power locking system fails (power fail ure) , you will need to lock the passenger door
separately.
; 0
"' ... m
F ig. 26 Passenger 's door : eme rge ncy re lease
F or this purpose, a mecha nic a l loc kin g device
i s pr ovided on t he end panel of the p assenge r
door (on ly visible when the door is open).
• Remove the cap
¢ fig . 26 .
Opening and clo sin g 33
• Insert the key into the inne r slo t and turn it
to the right as far as it can go.
A ft er yo u close the door yo u will no lo nger be
able to open it from the o utsi de. You can o pen
it from the inside, however, by p ulling on the
door latch twice.
Front lid
Opening /closing the front lid
1/
Fi g. 27 Drivers door : remo te front lid re lease
Fi g. 28 Release leve r un de r the fro nt l id
When opening the front lid, the windshield
wipers must be sw itched off and the w iper
arms m ust be folded against the windshie ld.
Otherwise the paint could be damaged .
Opening the front lid • Press the ce nte r button on the master key o r
• Pull the re lease button in the dr iver's door
¢ fig.27 .
• Pull up on the release u nder the front lid
¢ fig. 28 (arrow). Th is re leases t he catch .
• Open the front lid a ll the way .
Closing the front lid
... Pull the front lid down unt il the pressure
from the struts is reduced.
• Close the front lid.
34 Openin g and clo sing
• Press the front lid closed carefully using
both hands unti l it latches audibly¢ &,.
A WARNING
A front lid that is not comp lete ly latched
could fly up and block your view while driv
ing.
- When you close the front lid, check it to
make sure the safety catch has properly
engaged. The lid should be flush with the
surround ing vehicle body parts.
- If you not ice wh ile driving that the lid is
not secured properly, stop at once and
close it.
- Never leave your vehicle unattended es
pecially with the front lid left open. A
child could c rawl into the luggage com
par tment and pull the lid s hut, becoming
tr apped and unable to get out. To re duce
the risk of personal i njury, never let chil
dren p lay in or around your vehicle . Al
ways keep the front lid as we ll as the ve
hicle doors closed when not in use.
(D Note
Ma ke s ure no objects are protruding above
t he edge o f the luggage compartment.
Otherwise, the front lid could be dam
aged.
(D Tips
I f the front lid is open or not p roperly
locked w hen the ignit ion is tu rned on, the
door and front lid warning appea rs in the
instrument cluster disp lay.
Emergency release for front lid
If the front lid cannot be opened, an emer
gency release is provided .
Fig . 29 Sect io n: Eme rgency release
• Reach under the closed glove compartmen t.
There is a red plas tic cord under the glove
compartment .
• Pull the red plastic cord towards yo u.
Anti-theft alarm
system
The anti-theft alarm triggers an alarm if any
one attempts to break into the vehicle .
Fig . 30 Diode position in the instrument pane l
The anti -theft alarm system triggers an audi
ble a larm and turns on the emerge ncy flasher
if an unauthorize d interference with the vehi
cle is sensed by the system .
How is the anti-theft alarm system
switched on?
T he anti -theft alarm system is switched on
when you lock the driver's door manua lly us-
ing the fo ld-out key, or when you use the re
mote control. The system is activated approxi
mately 30 seconds after the vehicle is locked . .,,_
The indicator li ght q fig . 30 starts flashing
rapidly fo r 2 seconds and then blinks slowly.
How is the anti-theft alarm system
switched off?
The anti -the ft alarm system is switched off
on ly when you unlock your vehicle. If yo u do
not open a door with in 30 seconds after yo u
have unlocked with the remote control, the
ve hicle w ill lock itse lf again a utomat ically.
When will the anti theft alarm system be
triggered?
When the veh icle is locked, the alarm system
monitors and protects the following parts of
the vehicle:
- engine compartment
- luggage compartment
- doo rs
- ignition
When the system is activated , the alarm wi ll
be tr iggered if one of the doors, the eng ine
compa rtment lid or the front lid are opened .
The anti-theft a larm system will also go off
when the battery is disconnected .
You can a lso trigger the alarm by pressing t he
PANIC button on your remote-control key .
This will a lert other peop le in case of emer
gency . Press the
PANIC button again to tu rn
off the alarm .
How is the ant i-theft alarm switched off
when triggered?
The alarm system is switched off w hen you
u nl ock the vehicle us ing the remote-control
key or when the ignition is sw itche d on . T he
a larm w ill also switch itse lf off when it comes
t o the en d of its cycle.
Emergency flasher
The emergency f lasher w ill blink b riefly w hen
the doors, e ngine compartment l id and fron t
lid are properly clos ed .
If the emergency flashers do not blink, check
the doors, e ngine compartment l id and front
l id to make sure t hey a re p roperly closed . If
Opening and clo sin g 35
you close a doo r, the eng ine compartment lid
o r the fro nt lid with the anti -theft alarm
switched on, the eme rgency flashers w ill blink
o nl y after yo u have closed the door or lid.
@ Tips
For the a nti-theft alarm system to f unc
tion properly, make sure all ve hicle do ors
and windows are closed bef ore leaving t he
vehicle.
Power windows
Controls
Th e driver can opera te all windo ws.
F ig. 31 Driver 's doo r: power w indow sw it ches
T he powe r window swi tc hes have a two-posi
tion function :
Opening the windows
.,. Press the swit ch and hold it down u nt il the
w indow h as reached the desired posi tio n.
.,. Press t he swi tch
briefly to open the win dow
automatically .
... By briefly press ing/p ulling the sw itch again,
the downward t ravel of the window can be
stopped in any pos ition
¢ ,& .
Closing the windows
.,. Pull the sw itch and hold it until the w indow
has reached the desire d posi tion .
... Pull the sw itch
briefly to close t he window
automatically.
... By briefly pressing/pull ing the sw itch again,
the upwa rd trave l of the w indow can be
stopped in any pos it ion
¢ ,& . .,.
36 Openin g and clo sing
A WARNING
- Do not leave children unattended in the
vehicle, especially with access to vehicle
keys . Unsupervised use of the keys can
result in starting of the engine and use
of vehicle systems such as powe r win
dows , etc. which cou ld result in serio us
injury.
- Remember -you can still open or close
the power w indows for abou t ten m i
nutes after the ignition is sw itched off .
Only when either of the front doors are
opened are the power windows switched
off.
- Be careful when closing the windows .
Check to see that no one is in the way, or
serious injury could result!
- Always remove the ignition key whenever
you leave your vehicle.
- If you lock your vehicle from the outside,
no one, especia lly children, sho uld re
ma in in the vehicle .
- Do not stick anything on the windows or
the windsh ield that may interfere with
the driver's fie ld of vision.
@ Tips
- When the doors are opened, the w in
dows are a utomatica lly lowered 0.4 in
(10 mm) .
Reactivating the system after battery
disconnection
If the vehicle ba ttery i s disconnected and
then reconnected, the automatic closing and
opening function will not work until it is reac
tivated .
• Pull and hold the power w indow swi tch un til
the window is completely clo sed .
• Release the switch and pull it again for one
second.
40 Convertible top
The rear window can be extended comp lete ly
for cleaning. This is ca lled the cleaning posi
tion.
E xtendin g the rear w indow into th e w ind
d efl ector po sit io n
.. Pull and hold the rear window switch
¢ fig. 36 .
.. Re lease the switch once the rea r window has
reached the wind deflector position.
E xte nding th e rear window into th e
cle aning po sition
.. Pull and hold the rear window switch
¢ fig . 36.
.. Release the switch once the rear window has
reached the wind deflector position .
.. Pull and hold the rear w indow switch again .
.. Pull and hold the convertible top switch
within one second
¢ page 37, fig . 32.
Re tra cting the re ar w indow
.. Press and hold the rear window sw itch until
the window has been retracted .
Retra cting the re a r wi ndow using the one
t ouch function
.. Press the rear window switch briefly . There
is no need to hold the switch .
The rear window can only be operated when
t he igni tion is switched on.
The rear window can also be extended or re
tracted when the convertib le top is closed.
A WARNING
- Do not use the rear window to secure car
go or other objects. This could result in
mJury .
- Always pay attention and be careful
when extending or retracting the rear
window . It could cause injury by pinch
ing .
(D Tips
-Keeping all of the w indows raised pro
v ides the best wind protection . - The vehicle must be stationary to bring
the rear window into the cleaning posi
tion . The rear window will retract once
you begin dr iv ing .
Convertible top
emergency operation
General information
The convertible top can be closed by hand if
there is a malfunction .
First check if overload protection is active
¢ page 38. If this is the case, the convertible
top wi ll operate again afte r a short de lay. Oth
erwise the fo llowing steps must be completed
before closing the convertib le top:
.. Activate the pa rking brake .
.. Open the side w indows, if necessary.
.. Remove the key from the ignition.
E mergency loc king is not intended for long
term use or long d rives . The convertible top
will not be completely waterproof after using
the emergency locking procedure because the
seals wi ll not be seated correctly. Only close
the convertible top manually in an emergency .
Please see an authorized Audi R8 dealer to
have the cause of the malfunction corrected .
A WARNING
-The ignition must be sw itched off d uring
the entire closing p rocedu re.
- When pos itioning the convertible top,
avoid contact with the supports or other
movi ng parts. Otherwise you could p inch
your hands.
- Never drive when the convert ible top is
not locked correctly . The wind from d riv
ing could cause the convertible top to
open . This can resu lt in injuries and dam
age to the vehicle.
(D Tips
Have a second person assist when clos ing
the convert ible top. Opening the storage
bay lid and positioning the convertible top
i s easier when a second person is assisting.
42 Convertible top
Opening the conv ertible top stor age bay
lid
• From the r ear of the vehicle, r each into the
center ventilation slot in the sto rage bay lid
wi th both hands and raise the lid approxi
mately 12 in (30 cm).
• Hold the storage bay lid in this posit ion and
pull it toward you until it stops ¢
fig. 40.
A WARNING
When working in the engine compart
ment:
- T urn the engine off.
- Act ivate the park ing brake.
-
- In vehicles with a manua l transm iss ion,
move the sh ifter lever into idle . In
vehicles with the R tronic transmission,
move the se lector lever into the N pos i
t ion.
- Remove the ignit ion key .
- Let the engine cool down .
- Keep children away from the engine com-
partment.
(D Note
To prevent damage to the vehicle, only
open the convertible top storage bay lid
when the engine compartment lid is
closed.
Step 4: Remove the covers
Fi g. 41 Conv ertib le top : cov ers ma rk e d
Fig. 42 Co nver tible top storage bay lid: r em ov ing t he
c o ver
T he following steps mus t be performed on
both sides of the vehicle .
• Remove the bo lt in the cover on the bo ttom
side of the sto rage bay lid using the open
e nd w rench from the vehicle too l kit
(D
¢ fig . 42.
• Move the cover up and down carefully until
it can be pulled downwa rd from the teeth
@ .
Step 5: Lift the convertible top out
Fig. 4 3 Conve rtib le to p sto rage bay: liftin g th e c onve r
tible top o ut
Fig . 44 Wind shi eld fr ame: p res sing the c onvert ible top
fo rwa rd
• Ho ld the conve rtib le top at the@ point (ar
row)
r:!;> fig. 43 and raise it carefu lly ¢ A . .,..
46 Clear vision
Clear vision Lights
Switching the headlights on/off
F ig . 52 Instr ument pane l: light sw itch (automat ic
head· and ta illight control)
Switching on the side marker lights
• Turn the light switch to :oo:.
Switching on the headlights and high
beam
• Turn the light switch to ;D .
• Push the high beam lever forwa rd towards
the instrument panel~
page 47 .
Switching off the lights
• Turn the light switch to 0 .
Switching on automatic head -and
taillight control
• Turn the light switch to AUTO q fig. 52.
The headlights and taillights will come on au·
tomatically when the ignition is switched on
and the light switch is in the position AU TO
(on ly in nighttime conditions). When switch·
ing off the ignit ion, the headlights will go off
and only the side marker lights will remain lit.
Daytime running lights
USA models: The daytime running lights will
come on automatica lly when the ignition is
switched on and the light switch is in the posi·
tion
AUTO (only in daylight cond itions).
Canada models: The daytim e running lights
will come on automatically when the ignition
is switched on and the light switch is in the position
0
, AUTO (on ly in daylight condit ions)
or
:oo:.
Automatic head- and taillight control
In the switch position AUTO the automatic
head· and ta illight control is activated. Light
senso rs are located in the inside mirror hous
ing and constantly check the light conditions
surrounding the vehicle. If ambient bright·
ness falls below a factory set value (e.g. when
driv ing into a tunnel), the head- and taill ights
including the license plate illumination are
automat ically turned on. When amb ient
brightness increases aga in, the external lights
are turned off aga in
q ,&. . In the sw itch posi
t ion
AUTO , the low beams are turned off when
the ignition is switched off. The remaining
lights are turned off when the key is ta ken out
of the ignition lock.
With aut omat ic head- and taillight control,
the high-beam function is also available, but
with one restriction: If you have not switched
the high beams back to low beams during a u
tomat ic head light operation (for examp le, af
ter driving through a tunnel), on ly the low
beams come on the next time automatic
headlights are switched on. To use the high
beams, you first have to pull the h igh beam
lever back and then push the lever forward
again.
The side marker lights and headlights can be
switched on manually by turning the light
switch to the desired position .
Light sensor malfunction
If there is a light sensor ma lfunction, the
symbol
tal comes on in the display. For safety
reasons, the low beams are turned on perma
nently with the sw itch in
AUTO. However, you
can continue to turn the lights on and off us
ing the light switch. Have the light sensor
checked as soon as possible at an authorized
A udi dealer.
Coming home/leaving home function
The function is sw itched on when the sw itch is
i n the
AUTO position and the function is ...,