2014 AUDI A8 warning

22 Instruments and warning/indicator lights
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* ¢
page 247.
~ Windshield wipers
g,.5 Windshield wiper defective
There is a malfunction with the windshield
wipers.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
i§i l}D 10 $ Defective light bulb warning
I-If the indicator light turns on, a bulb has
failed. The message indicates the location of
the bulb.
II-if a fog lamp* has failed, the indicator
light turns on to indicate the location on the
vehicle.
a-if a rear fog lamp has failed, the indicator
light turns on to indicate the location on the
vehicle.
Vehicle lights: malfunction
If the message appears, there is a malfunc­
tion in the headlights or light switch .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
A WARNING
, -
- Light bulbs are pressurized and could ex-
plode while they are being changed caus­
ing serious personal injury.
- Work with due care when handling the
high-voltage section of gas discharge
(xenon) lights. Failure to do so could re­
sult in death or serious injury.
Have the bulb replaced or the connection
repaired by your authorized Audi Service
department.
~(D Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer working properly. Have
the system checked and repaired at your Audi
dealer.
§0 Adaptive Light
Applies to veh icles: w ith Adapt ive light
m;J Audi adaptive light: system fault
If the indicator light turns on and this mes­
sage appears, there is a malfunction in the
adaptive light system. The headlights still
function.
Go to an authorized dealership to have the
headlights or the control unit for the Adaptive
Light repaired.
@.D Light /rain sen sor
l;I Automatic headlights/automatic wipers:
system fault
If the indicator light turns on and this mes­
sage appears, the light/rain sensor is not
functioning correctly.
For safety reasons the low beams are turned
on permanently with the switch in
AUTO.
However, you can continue to turn the lights
on and off using the light switch. You can still
control all functions that are independent of
the rain sensor through the windshield wiper
lever .
Contact your authorized Audi dealer as soon
as possible to have the problem corrected.
@! Dynamic steering
l:rj Steering: system fault. you can continue
driving
If the indicator light turns on and the mes­
sage appears, the steering may be more diffi­
cult to move or more sensitive than usual. The
steering wheel may also be at an angle when driving straight. .,..

Instruments and warning/indicator lights 23
Drive s low ly to your authorized Audi dealer or
qualified workshop to have the malfunction
corrected .
,'I'M Dynamic steering: initializing
If thi s driver message appears and the indica­
tor light is flashing on the inst rument panel ,
dynamic steering is being reiniti alized . Once
you sta rt the engine after this is finished, the
steering whee l wi ll be easy to move . Re-initi­
alization might be necessary if the steering
wheel was moved hard to the left and r ight
while the veh icle was not moving. The displ ay
goes out as soon as initialization is complete .
A WARNING
-
Have the dynamic steering system mal ­
function repaired as soon as poss ible by an
authorized Audi dealer or any qualified
workshop - risk of accident!
@ Tips
-The dynamic steering stability systems
are not available in the event of a system
malfunction.
- For additional informat ion on dynamic
steering, refer to
¢page 110.
I-: Sport differential
Ill Sport differential: system fault
There is a malfunct ion with the sport differen ­
tial.
Drive to your authori zed Aud i dea ler immedi­
ately to have the malfunction corrected.
Ill Sport differential: overheating
The transmission temperature has incre ased
sign ificantly due to the sporty driving manner.
Dr ive in a less sporty manner until the tem­
pe rat ure returns to the normal range and the
indicator light switches of.
A WARNING
Contact your authorized Audi dealer or a
qualif ied workshop if the sport different ial
is faulty or malfunctioning . The repa ir
-
must be performed by trained personnel
using the correct oil in order to ensure
safety.
¢¢ Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left II or the r ight II
turn signal, the indicator light blinks. When
you use the emergency f lashers, both indica­
tor lights flash .
If one of the turn signa l light bulbs burn out,
the turn signal wi ll blink twice as fast as nor­
mal. Carefu lly drive to your authorized Audi
dealer immed iate ly to have the malfunction
corrected. The indicator light does not indi­
cate a malfunction if a turn signal on the tra il­
er or on the vehicle fails in trailer tow ing
mode .
(D Tips
For more information on the turn s ignals,
refer to¢
page 48.

24 Instruments and warning/indicator lights
Driver information
display
Overview
Fig. 4 Driver informat ion system in the instrument
cluster
Fig. S D isplay: example of th e informat ion line
The driver information system contains infor­
mation @ that is displayed on tabs @
c:;, fig. 4. The following content is possible de­
pending on vehicle equipment:
@
®
Tab Content
1 Vehicle functions :
On-board computer c::> page 25
Digital speedometer
Cruise control*
c:;, page 91
Adaptive cruise control and braking
guard*
c:;, page 94
Audi lane assist* c::> page 103
Display darkened
2 Indicator lights and messages
Warning when a door, the hood or the rear lid is not closed
c::>page29
Service interval display c::>page 28
Speed warning system ¢page 91
@ ®
Tab Content
3
Night vision assistant* c:;, page 113
4 Audio/video
s Telephone*
6 Navigation*
T he second and th ird tabs are only vis ible if at
least one indicator light or message is shown
or if that system is sw itched on.
The status line © is located in the bottom
part of the display
c::> fig. 4. It displays the ex­
terior temperature , time, selector lever posi­
t ion, trip odometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
c::> page 25 in the line (D c::> fig. 5.
_& WARNING ,___ -
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
slippery even at an outside temperature
above 41 °F
(+5 °() .
- Always remember, even if the "snow­
flake" symbol (ice warning) does not ap­
pear in the d isplay, black ice could be on
the road .
- Always reduce your speed and drive with special care in cold weather cond itions
when the chance of encountering icy
road surfaces increases.
(D Tips
-At temperatures below 14 °F (+ 5 °C) a
snowf lake symbol appears ahead of the
temperature display. It is intended to re­
m ind the driver to pay special attention
to
ice on the road c::> ,&. If the vehicle is
stationary, or if you are driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual outs ide temperature. This is .,.

Instrument s and warning /indicator lights 25
caused by the heat being radiated from
the engine.
- You can se lect the un its used fo r temper­
atu re, speed and othe r measurements in
the MML
- Fo r informa tion on the a udio/video and
navigation* functions, refer to the se pa­
r ate MMI ow ner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
gi g ~------,i
~
F ig . 6 Mult ifu nct io n stee ring wheel: operat ing t he d riv­
er informat ion system
Fi g. 7 Driver informat ion system: ope ning the ve hicle
funct io ns m en u
Operating concept
.. Switch the ign ition on.
.. To sw itch between t he tabs, press th e rocker
switch @to the left or right
c> fig . 6 .
.. To access additional informat ion be low or
above, rotat e the thumbwheel @ dow n or
up.
.. To confi rm a selection, press t he thumb­
whee l@ .
Accessing Vehicle functions
.. Sele ct the first t ab with the ro cker swit ch
@.
.. Press the b utton [jg] _ The Vehicle funct ions
menu appears c> fig . 7.
.. To select a menu item , tu rn and press t he
thumbwhee l@ .
Resetting values to ze ro
.. Select the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
men u.
.. Yo u can now select between t he long-term
memory and s hort-term memory .
.. To reset the values in a memory, p ress a nd
hold t he thumbwheel @ for one second .
The last function selected d isp lays when you
switc h the ig nition on.
On-board computer
You can ca ll up the followin g in formation in
the on -board computer:
- Date
- Dr iving t ime (h) from the shor t-te rm memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph ( km/h) from the
short-te rm memory
- Distance driven in miles (km) from the
short-te rm memory
- Cur ren t fue l consumption in MPG ( l/100
km)
- Short-term memory overview
- Long-term memory overview
T he short-te rm memory collects driv ing infor­
mation from the time the ign ition is switc hed
on until it is switched off. If you continue driv­
ing within two ho urs after switch ing the ig ni­
tion off, the new values are included when cal­
cu lating the c urrent trip information .
Un like the short -term memory, the long-term
memory is not erased automatically. You can
select the time period for evaluating t rip in­
format ion yourse lf .

26 Instruments and warning/indicator lights
For some vehicle functions, you can access the
trip information from the t emporary memory
in the line
(D ~ page 24, fig. 5.
The current fuel consumpt ion can be dis­
p layed using a bar~
page 2 7, fig. 10. The
average consumption (mpg) stored in the
short-term memory is also d isplayed. Electri ­
cal energy can be stored in the battery when
t he vehicle is coasting or driving downhill (re­
cupe rat ion) . The bar will move toward D.
Efficiency program*
The efficiency program can help you to use
less fuel. It evaluates driving information in
reference to fuel consumption and shows oth­
er equipment influencing consumption as well
as shift recommendations .
c:> page 26. Fuel
economy messages ~
page 26 provide tips
for eff icient driving . The eff ic iency program
uses distance and consumption data from trip
compute r
1.
To display the efficiency program, call up Ve­
hicle functions and select the menu option
Efficiency program .
If the data are deleted in
the efficiency program, those values are also
reset in trip computer.
@ Tips
-All stored va lues w ill be lost if the veh i­
cle battery is disconnected .
- Fuel consumptions (ave rage and cur­
r ent), range and speed are displayed in
metric units on Canadian models.
Other equipment
Applies to vehicles: with efficiency program
Fig. 8 Tri p comp uter: othe r equ ipment
Requirement: The efficiency program must be
displayed
c:> page 26 .
,. Tur n the thumbwheel unti l the other equip-
ment appears in the display.
Other equipment th at is currently affecting
fuel consumpt ion is listed in the effic iency
program. The display shows up to three other
items of equipment @. T he equipment using
the most fuel is listed first. If more than three
items using fuel are switched on, the equip­
ment that is currently using the most fuel is
displayed .
A scale @also shows the current tota l con­
sumption of all other equipment.
Fuel economy messages
Applies to vehicles: with efficiency program
Fig. 9 Display : example of a fuel econo my m essage
Fuel economy messages are displayed when
f uel consumption is increased by certa in con­
ditions. If you follow these fue l economy mes­
sages, you can reduce your vehicle's consump­
tion of fuel. The messages appear automati ­
cally and are only displayed in the efficiency
program. The fuel economy messages turn
off
automatically after a certain per iod of time .
.,. To turn an economy message
off immediate­
ly after it appears, press any button on the
multifunction steering wheel.
(D Tips
- Once you have turned a fuel economy message
off , it will only appear again af-
ter you turn the ign ition on again . .,,.

Instrument s and warning /indicator lights 2 7
-The fuel economy messages are not dis­
played in every instance, but rathe r in in­
terva ls
over a period o f time.
Cylinder on demand System
App lies to vehicles: w ith 4 .0 TFS ! engi ne
F ig. 10 Inst rume nt cluster: fuel consumption
To save fu el, the eng ine automat ic all y t urns
four cylinders o n or
off, de pending on the
amo unt of power needed. This action is not
fe lt by the passengers.
Displaying cylinder mode
Requirement: t he on-bo ard computer is di s­
pl ayed~
page 25.
~ Turn the thumbwhee l until the current fue l
c o nsu mption display is shown in the inst ru­
me nt cl uster.
If the green ba r is d ispl ayed,
yo u a re driving in 4-cylin der m ode.
Basic requirements for 4 -cylinder mode
4-cy linder drive mode is used automatically if
certain basic requir emen ts are fulfi lled. These
in clude:
- A low powe r output requi reme nt.
- Driving in third gear or higher.
- Engine speed between 960 and 3,500 RP M.
-A warm engine .
Odometer
Fig. 11 Instrument cluste r Odo meter a nd reset button
The odometer shows you how many m iles
(k ilometers) you have driven. You can switch
the d isplay from miles to kilomete rs and v ice
versa via t he MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset.
It can be used to meas­
ure s ho rt d istances . The last digit indicates
1/10 of a mile (100 meters) .
You can reset the trip odometer to zero by
pressing the Reset button~-
Lower odometer
The lower odomete r shows the tota l num ber
of m iles (kilometers) dr iven.
Malfunction message
I f th ere is a malfunc tion i n the in strumen t
cl us ter,
DEF will ap pear i n the trip odometer
display a rea. Conta ct your author ized Audi
dealer to have the problem corrected.
Time and date display
Fig . 1 2 Ce nter console: ana log clock

28 Instruments and warning/indicator lights
The date and time are shown in the instru­
ment cluster d isplay
c:;, page 24, fig. 4. There
is also an ana log clock in the center console
c:;, fig. 12.
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds . When the ign ition is switched
on, the time is always displayed in the status
line © regardless of the current display.
You can set the time on both clocks and the date display in the MMI. Refer to the MMI
owner's manual for instructions.
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 13 Inst rume nt cluster: Serv ice inte rval d isp lay
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition on
c:;, fig. 13 .
After about S seconds the display switches back to normal. The distance and time re­
maining are updated each time the ignition is
switched on until the date due for service is
reached .
Service due
When the due date for service is reached, the
message
Service due! appears in the instru­
ment cluster immediately after you switch the
ignition on . Additionally, a warn ing tone sounds. After about 5 seconds the disp
lay
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > Car sys­
tems
control button > Servicing & checks >
Service interval displays.
Resetting the service interval display
Your authorized Audi dealer will reset the cor­
responding service schedule after performing
the appropr iate service on your vehicle. You
also have the possibility to reset the oil
change schedule after hav ing performed an
o il change according to Aud i specif ications.
Select the
I CAR I function button > Car sys­
tems
control button > Servicing & checks >
Service Intervals > Reset oil change interval.
(D Note
If you disconnect the battery term inals, no
calculations can be made for the service
i nterval disp lay during th is time and no
serv ice reminder will appear. Remember
that observing the proper service intervals
i s vitally important to extending the life of
your vehicle, pa rticularly the engine, and
maintaining its value. Even if the mileage
driven is low, the maximum period of one
year from one service to the next must not
be exceeded.
(I} Tips
-Do not reset the display between oil
changes, otherwise the disp lay w ill be in­
correct.
- The information in the Service Reminder
remains stored
even when the vehicle
battery is disconnected .

Instrument s and warning /indicator lights
Open door/hood/rear lid warning
Fig. 14 D isplay: doors and rear lid open
With the ignition switched on, the warning il­
luminates when at least
one door or the hood
or the rear lid is not closed. The symbol also
shows you
which door(s) or lid is not closed.
In the illustration ¢
fig. 14 it is the driver's
door and the left rear door.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4 in
the instrument cluster is part of the On-Board Diagnostic (OBD II) system.
The warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized.
This indicates that the MIL is work ing proper­
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv­
ing, a malfunction may ex ist in the engine sys­
tem. If the light illuminates, the catalytic con­
verter could be damaged.
Continue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erat ions) and have the condition corrected.
Contact your author ized Audi dealer.
If the light illuminates, the electronic speed limiter may also be malfunctioning. For more
in formation ¢
page 30, Electronic speed
limiter.
An improperly closed fuel filler cap may a lso
cause the MIL light to illuminate¢
page 225.
On-Board Diagnostics
Fig. 15 Location of Data Link Connector (DLC)
On-Board Diagnostics monitors the compo­
nents of your emission control system. Each
monitored component in your engine system
has been assigned a code . In case of a mal­
funct ion, the component will be identified
and the fault stored as a code in the control
module memory.
The MIL light may also illuminate if there is a leak in the on -board fuel vapor recovery sys­
tem.
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed ¢
page 225.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe­
cial diagnostic equipment (generic scan tool
for OBD).
In order to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC). The DLC is located to the
right of the hood release
¢fig. 15.
Your authorized Audi dealer or a qualified
service station can interpret the code and per­
form the necessary repair.
A WARNING
Do not use the diagnost ic connector for
personal use. Incorrect usage can cause
malfunctions, wh ich can increase the risk
of a collision!
-
29