2014 AUDI A8 seats

64 Seats and storage
@ Tips
If you cannot move the seat into the re­
clining position, it may be because
- the front passenger's seat memory func­
tion is switched off¢
page 67 or
- the child safety lock is switched on (the
~ button ¢ page 41 or the right t but­
ton ¢
page 41 light s up in the driver's
door), or
- the front passenger seat adjustment is
switched off in the MMI ¢
page 64.
Massage function remote control
Applies to vehicles: with reclining rear seat an d massage
fu nct ion
Fig . 60 Remote control: reclining seat massage func­
tions
The remote controls are located in the rear
center console¢
page 68, fig. 65. The mas­
sage function is on ly available when the igni­
tion is switched on.
• To open the remote control compartment,
press the left button and fold the center
armrest upward.
• To adjust the massage type, press the ap­
propriate button@-@ . The LED in the but­
ton will turn on.
• To adjust the speed/intensity, turn the
thumbwheel @I® . Th e LEDs indicate the
speed/intensity.
• Press the selected massage type again to
switch the massage function off.
Massage types
@ -Wave
@-Pulse
©-Stretch @
-Lumbar
© Tips
- The massage function switches off auto­
matically after approximately 10 mi­
nutes.
- If you activate a massage type again, the
last selected intensity and speed will be
selected.
Comfort settings
Applies to vehicles: wit h comfort seats in the rear
You can adjust settings for the rear seat from
the cockpit using the MMI.
• Select !CARlfunction button> Car systems
control button > Vehicle settings > Seats >
Rear seats.
Factory settings position -
This function
moves the outer rear seats and the front pas­
senger seatback into the factory settings posi­
tion.
Entry assistance -Entry assistance makes it
easier to enter and exit the rear seat more
comfortably. When the function is activated,
the rear seat moves all the way back automat ­
ica lly when the corresponding door opens.
Front passenger seat adjustment* -If the
function is activated in the MMI, the front
passenger seat can be adjusted from the rear
seat¢
page 61, fig. 57.

Head restraints
Adjusting the head restraints
Head restraints that are adjusted according
to body size, along with the safety belt, offer
effective protection.
Fig. 61 Comfort head restraints: adjusting the side
bolsters
Fig. 62 Outer rear seat: ad justing th e head restraint
Adjust the head restraint so the upper edge is
as even as possible with the top of your head.
If that is not possible, try to adjust the head
restra int so that it is as close to this position
as possible
r=:>page 65.
Adjusting front head restraints
• To adjust the height of the front head re­
straints, press/push the button ©
opage 59, fig . 54 up/down o _& .
• Vehicles with reclining rear seat: Grasp the
s ides of the passenger's head restraint with
both hands and slide it upward/downward.
Adjusting rear head restraints (adjustable
head restraints)
The center rear head restraint is not adjusta­
b le.
Seats and storage 65
• Grasp the sides of the head restraint with
both hands and slide it upward until you feel
it click into place r=:>
A.
• To lower the head restraints, press button -
small arrow -
o fig. 62 and slide the head re­
straint all the way down .
Adjusting the side bolsters*
• To adjust the side bolsters *, press them into
the desired position
c:> fig. 61.
Refer to¢ page 139, Proper adjustment of
head restraints
for guidelines on how to ad­
just the height of the front head restraints to
suit the occupant's body size.
&_ WARNING
-
- All seats are equipped with head re-
straints. Dr iving without head restraints
or with head restraints that are not prop­
erly adjusted increases the risk of serious
or fatal neck injury dramatically.
- Read and heed all WARNINGS
o page 139, Proper adjustment of head
restraints.
- Vehicles with a pass through in the cen­
ter conso le have seating for four. The
long center console between the two
rear seats is
not a seating position.
Therefore, a safety belt is not provided.
(D Tips
- T o prevent the head restraints from run­
ning into the headliner, they retract au­
tomatically when moving the seat for­
ward or upward.
- Correctly adjusted head restraints and
safety belts are an extremely effective
combination of safety features.

66 Seats and storage
Seat memory
Description
Applies to vehicles: wit h memory fu nctio n
The memory function allows you to quickly
and eas ily store and recall personal seating
p rofiles for the dr iver, front passenger and
outer rear seats*. The memory function is op­
erated through the master key and the memo­ ry buttons in the driver's/front passenger's
doors and the rear doors*.
The driver's seating profi le is stored and as ­
signed to the master key each time the vehicle
is locked . The seating profile is recalled auto­
matically when the vehicle is unlocked. If two
Remote control
master key
Driver
Seat X
Head restraint X
Steering wheel* X
Safety belt* X
Both exterior rear-X
view mirrors*
There are two additional buttons in the rea r
doors* that can be used to recall two stored
seating profiles
r:=;,page 67.
Remote control key
Appl ies to vehicles: with memory function
To assign the driver's seat settings to the re­
mote contro l key when locking the vehicle, the
function must be switched on .
.. Se lect :
I CAR I function button > Car systems
control button > Vehicle settings > Seats >
Driver seat > Remote control key> On.
@ Tips
If you do not want another driver's set­
tings to be assigned to the remote control
key, switch off the memory function using
the MMI or the
! OF F! button r:=;, page 67. people
use one vehicle, it is recommended
that each person always uses "their own"
master key.
Two seating profiles can be stored in each of
the driver's/front passenger's doors and one
seat ing profile in each of the rear doors*.
Once stored, these seat ing profiles can be re­
ca lled at any time.
T he following sett ings are stored:
Memory button
Driver Front passenger Outer rear seats*
X
X X
X X
X
X
X
X

Memory buttons
Applies to vehicles: with memory function
Fig . 63 D river's door: memory function buttons
Fig. 64 Rear door: memory fun ction buttons
The memo ry buttons are located in the dr iv­
er 's/fr ont passenger's door and in the rear
doors* .
Storing seating profiles
.. To s tore a seating profi le, press the ISETI
button and then one of the memo ry but­
tons .
.. To recall a seating p rof ile, p ress and hold
the memory button until the seat is adj ust­
ed to t he stored settings.
.. To switch the memo ry function for the d riv­
er o r front passenger off, p ress th e
IOFFI
button. The word OFF ligh ts up when the
memo ry fu nctio n i s sw itche d off . S eating
p rofi les will not be s tore d.
Adjusting the reclining position/standard
position
.. To adju st the re clining posit io n, press and
hol d the @ button until the seat move s into
the end position .
.. To a dju st the stan dard pos it ion, press and
hold the @ button until the sea t moves into
the end position. Seats and storage 67
A WARNING
-
For safety reasons, the seat setting
should o nly be recalled w hen the veh icle
is stationary -otherw ise you risk hav ing
a n accid ent.
- If necessa ry, you stop the process by
press ing the
!OF F! button or any of the
m emory buttons.
Adjusting the front passenger seat in
the MMI
Applies to vehicles: with memory function
The driver can adjust the posi tion of the front
passenger seat.
Adjusting the front passenger seat from
the driver's side
.. Sele ct: !CAR I func tion butt on> Car systems
con trol bu tton > Vehicle settings > Seat s >
Front passenger seat > Adjust seat posi ­
tion .
.. You ca n now ad just t he front passen ger seat
using the buttons on the driver's seat
<=> page 59 , fig. 54.
Matching the position of the driver's seat
.. To adjus t the front passenge r se at to m atch
t he driver's seat settings, se lec t th e
ICARI
function button > Car systems cont ro l but­
ton
> Vehicle settings > Seats > Front pas­
senger seat > Symmetry to driver seat .
.. Press and hold the contro l knob until the ad­
justment process is complete .
@ Tips
When matching seat settings, the settings
for the lumbar support and seating sur­
face will no t tra nsfer to the front passe ng­
e r's seat.

68 Seats and storage
Full-length center
console
Overview
Appl ies to vehicles: with full-len gth ce nter console
Fig. 65 Rear: full -length center console
@ · 115 volt socket ¢ page 68
@ · cupholder <=> page 75
© · 12 volt socket c:> page 7 4
@ · Folding table ¢ page 69
® ·center armrest and storage com part ·
ments: to open the deep compartment, press
the r ight button and fo ld the center armrest
upward. To open the compartment fo r the
massage func tion remote con trol*
c:> page 64
and fo r the telephone* , press the left button
and fo ld the center armrest upward.
115-volt socket
App lies to vehicles: with 115 -vo lt socket
The 115-vo lt socket can only be used when
the engine is running¢
A. When you push
the connector all the way into the socket, the
child safety mechan ism releases and current
flows through the socket .
Equipm ent that can be conn ected
Electrical devices can be connected to the 115
volt socket in the veh icle. Power consumption
at the 115-volt socket must not exceed 150
watts (300 watts peak) . Check the power con·
sumpt ion of the equipment on the model
p late .
LED on th e socket
- The socket is ready for use when the L ED is
green.
- If the LED blin ks red, there is a ma lf u nction.
The socket wi ll swi tch off automa tica lly due
to overcu rrent or overheating. The socke t
will switch on again automatica lly after a
coo l-down period. Any devices that are con­
nected and switched on will activate again
automatically
c:> A .
A WARNING
-
- The sockets and the electr ical accessories
connec ted to them operate only when
the ignition is switched on. Incorrect us­
age can lead to ser ious injuries or burns.
To reduce the risk of injuries, neve r leave
chi ldren unattended in the veh icle with
the vehicle key .
- H eavy equipment or plugs with in tegrat­
ed power s upply units can damage the
socket and lead to injur ies .
- Sto re a ll connected e quipment securely
while the veh icle is moving so that they
cannot be thrown through the veh icle in
the event of a braking maneuver or an
accident.
- Never sp ill any liquids on the socket . If
any mo isture gets into the socket, make
certain that all the moisture has dried up before using the socket again.
- Equipment that is connected to the vehi·
cle socket can heat up more than it does
when connected to the public gr id .
- When us ing adapters and extens ion
cords, the child safety for the 115-volt
socket is d isabled and the socket is live.
- Never insert anything other than the
p lug of an appropriate e lectr ical accesso·
ry in to the socket, especially th ings that
conduct e lectr icity, e.g . meta l pens, kn it­
ting needles, etc. in to the cont acts of the
1 15-volt so cket.
- Turn the electrical equ ipment off if the
socket has switc hed off because of over·
heat ing.

70 Seats and storage
Luggage compartment
Tie-downs and luggage compartment
net
The luggage compartment net prevents small
objects from sliding.
Fi g. 68 Loca tion of the fasten ing eyes in the lu ggag e
compartment
Fig. 69 Lu ggage compartme nt net un hooke d
"To secure objects with the luggage compart­
ment net", fold the tie-down bracket up­
wa rd
~ fig . 68 .
"Inse rt the hooks on the luggage compart­
ment ne t* into the tie-downs
9 fig. 69 .
"Read and heed all WAR NINGS 9 page 141,
Stowing luggage .
In a collis ion, the laws of phys ics mean that
even smaller items that are loose in the vehi­
cle will turn into heavy missiles that can ca use
serious in jury . Items in the vehicle pick up ki­
netic energy which varies w ith the vehicle and
the weight of the item . Vehicle speed is the
most signif icant factor.
F or example, in a frontal coll is ion at a speed
of 30 mph (48 km/h), the forces acting on a
10- lb (4 .5 kg) object are about
20 times the
normal weight of the item . This means that
the we ight of the item would suddenly be the equivalent of about 200 lbs (90 kg). One can
easily imagine the injuries that an
item of that
weight flying freely through the passenger compartment can cause in a collis ion at a
speed considered relatively low .
A WARNING
-Weak, damaged or imprope r straps used
to secure items to tie-downs can fail dur­ in g hard braking or in a collision and cause
se rio us personal injury.
- Always use su itable reta ining straps a nd
p roperly secu re items to the tie-downs in
the l uggage compa rtment to he lp pre­
vent i tems from shift ing or fly ing fo r­
ward.
- Never at tach a chi ld seat tether strap to
a t ie -down.
- For s trength-re lated reasons, the mou nt­
ing hooks can only be used to secure ob­
jects weighing up to 10 lb. (5 kg) . Heavi ­
er objects will not be adequately sec ured
- there is a risk of injury.

Pass-through with ski
sack
Preparing the pass-through
Applies to vehicles: with pass-through and ski sack
Long objects such as skis can be transported
in the ski sack.
Fig. 70 Rear bench seat: removing the protect ive cover
Fig. 71 Rear center armrest: attaching the protective
cover
~ Fold the rear center armrest and the cover
located behind it down.
~ Press the button to remove the protective
cover ¢
fig. 70.
~ To protect the front area of the center arm­
rest, position the cover as illustrated
¢
fig. 71 and press the suction cups down so
they adhere.
~ Remove the ski sack and unfold it.
Seats and storage 71
Loading and securing the ski sack
Applies to vehicles: with pass -through and ski sack
--~ --
·-- --· ----~-
Fig. 72 Luggage compartment: pass-through in th e
backrest
Fig. 73 Rear bench seat: sec uring the sk i sack
Loading
~ Fold the pass-through cover in the luggage
compartment down
c:;, fig. 72.
~ Slide the pointed end of the skis into the ski
sack first¢ ,&.. Th e front pa rt of the bind­
ings must be directly under the securing
strap on the ski sack@¢
fig. 73.
Securing
~ Insert the securing strap @ on the ski sack
into the center safety belt latch ©
c:> fig. 73.
~ Tighten the securing strap@.
Securing (vehicles with full-length center
console)
In the pass-through, two securing straps are
in the hooks located in the luggage compart­
ment .
~ Hook the hooks into the front tie-downs in
the luggage compartment .
~ Tighten the securing strap @in the rear.

7 2 Seats and storage
& WARNING
- The ski sack is intended only for the
transportation of skis and other light ob ­
jects . To reduce the risk of serious per­
sonal in jury, never t ransport heavy or
poin ted objects in the ski sa ck.
- When brak ing rapidly or during an acci­
dent, the load could be displaced and
ca use i njury to occupants.
- Sharp edges on the load must be cove red
for protect ion. Always fasten the belt
ti gh tly around the sac k and its contents
¢ fig . 73.
-For safety reasons, do not t ransport
more than two pairs of skis in the ski
sac k.
- You m ust sec ure the ski sack with t he
st rap a fter loading.
- Make su re a ll objects that you are trans­
porting in the pass-through are secured.
Otherwise they cou ld slide around during
sudden braking maneuvers and cause in ­
jury.
@ Tips
- Never stow the sk i sack away whe n it is
still wet or damp (for examp le, sn ow
melt ing from sk is) . Allow it to dry com­
plete ly before stowing it away .
- Position skis in the ski sack with the pointed ends facing t he front and ski
po les w ith the pointed ends facing the
rear.
Roof rack
Description and mounting locations
Additional cargo can be carried wi th a roof
luggage rack .
Fig . 74 Roo f ra ck attac hment po ints
.. Always read and follow the instr uct ions pro­
vided by the roof rack ma nufacturer when
i nstall ing the roof rack system .
If luggage or cargo is to be ca rried on the
roof, yo u mus t observe the follow ing:
- To enhance the vehicle 's streamlined design,
ra in gutters have been mo lded i nto t he roof .
I t is not poss ible to use normal roof ra cks.
O nl y install a roof ra ck specific ally designed
for your model AB . Contac t the nea re st Audi
dea ler for information on approved modular
roof racks for your v ehicle.
- On ly use roof racks approved for your vehi­
cl e. These approved roof racks are the basis
fo r a complete roof rack system. Addition al
a tta chmen ts or carr ier systems are needed
t o transpor t luggage and spor ts equipment.
We recommend using roof rack s from the
Aud i original accessories prog ram.
- When insta lling the roof rack, make sure it
is o nly mounted on the designated locations
on the roof~
fig. 74 .
-We recommend that you keep the i nstalla ­
tion instruct ions for your roof rack system
together w ith your Owner's literature in the
ve hicle.
When should the roof rack be removed?
- Before go ing through an au tomatic car wash
(it is best to ask the ca r wash operator for
adv ice)
...