Instruments and warning/indicator lights 21
speed. This ind icates that the MIL is working
properly.
The warning light illuminates when there is a
mal funct ion in the engine e lectronic system.
Contact your authorized Audi dealer and have
the ma lfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illum inate
r:!,> page 204.
For more informat ion r:!,> page 30 .
!?) Engine speed limitation
App lies to vehicles: wit h eng ine speed lim itat ion
Ill Do not exceed max. engine speed of
XXXX rpm
The Ill symbol illuminates when there is an
engine control malfunction . The
'3i indicator
l ight in the instrument cluster also illumi
nates. The engine speed is lim ited to the
speed displayed in the driver information sys
tem . Keep in mind that the engine speed will
not exceed the va lue disp layed in the driver in
formation system, for example when down
shifting.
Drive to your authorized Audi dea ler immedi
ately to have the malfunction corrected .
'.!2:;,.,, Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your au
thorized Audi dealer and have the oil sensor
inspected. Until you have this done, check the
oil level each time you refuel just to be on the
safe side
r:!,> page 211 .
Bil Tank system
(iD Please refuel
If the indicator light turns on for the f irst
time and the message appears, there are
about 2.1- 2 .4 gallons (7 -9 liters) of fuel left
in the tank. Time to refuel
r:!,> page 203.
DD Fuel tank system malfunction! Contact
dealer
If the indicator light turns on and this mes
sage appears, there is a malfunction in the
tank system.
Drive to your authorized Audi dealer immedi
ate ly to have the malfunction corrected.
C> Windshield washer fluid level
II Please refill washer fluid
If the symbol illum inates, add windshield
washer fluid to the washer system and also to
the headlight washer system*
r:!,> page 220.
~ Windshield wipers
El Windshield wiper defective
The re is a malfunc tion with the windshie ld
wipers .
Drive to your author ized Audi dealer immedi
ate ly to have the malfunction corrected .
~/ }D /0$ Defective light bulb warning
If the S:$ indicator light turns on, a bulb has
failed. The message indicates the location of
the bu lb.
- If the
El indicato r light also turns on, then
a fo g lig ht has failed. The position of the in
dicator light corresponds with the location
on the vehicle .
- If the
II indicato r light also turns on, then
a rear fog * light has failed. The position of
the indicator light corresponds with the lo
cation on the vehicle .
T his wa rning can also occur if the light switch
is in an unengaged position between two sym
bols.
Vehicle lights: System fault!
If the message appears, there is a malfunc
tion in the headlights or light sw itch .
Drive to your authori zed Audi dealer immedi-
ately to have the malfunction corrected .
IJJ,,
50 Clear vis ion
is sw itched b ack on by mov ing the
winds hield wiper lever to any position .
- Worn or dirty windshie ld wiper b lades
r es ult in streaking. This can affect the
rain sensor* function. Check your wind
shield wiper b lades regularly.
- The was her fluid nozzles of the wind
s h ield washer system are heated at low
temperatures when t he ignit ion is on.
- When stopping temporarily, (e .g . at a
traff ic light) the set speed of the wind
shield wipers is automatically red uced by
one speed.
Cleaning windshield wiper blades
C lea n the w indshield wiper blades when they
begin to leave streaks . Use a soft cloth and
g lass cleaner to clean the winds hield wiper
b lades.
,. Place the windshield wiper arms in the serv
i ce position . Refer to ¢
page 50.
,. Lift the w iper arm away from the front win
dow.
& WARNING
Dirty windshie ld w iper blades can impa ir
your view. This can lead to acc idents .
Replacing windshield wiper blades
Fig . 4 6 Remov ing w inds hie ld w ipe r blade
-
Wiper service position /blade replac ement
position
,. Swi tch the ig nition off and move the w ind
shield wiper leve r to posit ion @ ¢
page 49,
fig. 45 . The wi ndshield wipe rs move into the
service position. ,.
To bring the w ipers back into the origina l
position , switch the ignition on and p ress
the windshield wiper lever.
You can also t urn the serv ice posi tion on or
o ff
in the radio/M M!*:
,. Switch the windshie ld wipers
off (position
@ ¢ page 49, fig. 45) .
,. Select: !CAR I function button> Windshield
wipe rs
> Ser vice position > on/off . Or
,. Select:
!CARI function button > Car systems*
cont rol butto n > Servicing & checks > Wiper
s ervice position
> On /Off .
Removing the wiper bl ade
,. Lift the windsh ie ld wiper arm up from the
w indshield.
,. Press the locking knob
(D ¢ fig. 46 o n the
w iper blade . Hold the wipe r blade firmly .
,. Remove the wipe r blade in the direction of
t he arrow .
Attaching the wiper blade
,. Insta ll the new wiper blade in the reta iner
on the wiper arm @unt il you hear it click in
to p lace on the w iper arm .
,. Place t he wiper a rm back on the windshield.
,. Tur n the se rvice position
off.
& WARNING ~
F or your safety, you sho uld rep lace the
wiper b la d es once o r twice a yea r. See your
authorized Audi dealer fo r replacement
b lades.
(D Note
- T he windshie ld wiper b lades m ust only
be rep laced when in the service position!
Otherw ise, you risk damag ing the pa int
on the hood o r the windshie ld w iper mo
tor.
- Yo u should not move your veh icle or
press the windsh ie ld wiper lever when
the wiper arms are folded away from the
w indshield. The winds hield wipers wou ld
move back into their or iginal position
and co uld damage th e hood a nd wind
shield.
