56 Clear vision
-If swallowed and person is conscious,
rinse mouth with water for at least 15
minutes. Do not induce vomiting unless
instructed to do so by medical professio
nal. Get medical attention immediately.
d) Note
Liquid electrolyte leaking from broken mir
ror glass will damage any plastic surfaces
it comes in contact with. Clean up spilled
electrolyte immediately with clean water
and a sponge.
@ Tips
- Switching off the dimming function of
the inside rear view mirror also deacti
vates the automatic dimming function of
the exterior mirrors.
-Automatic dimming for the mirror only
operates properly if the light striking the inside mirror is not hindered by other ob
jects.
- The automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected.
Sun visors
1--~---'
Fig. 62 Driver's side: sun visor
The sun visors for the driver and passenger
can be pulled out of their brackets in the cen
ter of the vehicle and turned towards the
doors @.
The mirror light switches on when the cover over the vanity mirror@ opens.
Wiper and washer
system
Switching the windshield wipers on
Fig. 63 Windshield w iper lever
Move the windshield wiper lever to the corre
sponding position:
@ -Windshield wiper off
@ -Interval mode. To extend/shorten the
wiper intervals, move the switch@ to the
left/right. In vehicles with a rain sensor* the
wipers turn on in the rain once the vehicle
speed exceeds approximately 2 mph (4 km/h).
The higher the sensitivity of the rain sensor* is
set (switch @ to the right), the earlier the
windshield wipers react to moisture on the
windshield. In some models, you can switch
rain sensor mode off and switch intermittent
mode on in the MMI*. Select:
!CARI function
button
> Car systems* control button > Driver
assist
> Rain sensor . In intermittent mode,
you can adjust the interval time using the@
switch.
@ -Slow wiping
@ -Fast wiping
@-Single wipe
® -Clean the windshield. To eliminate water
droplets, the windshield wiper performs one
afterwipe operation after several seconds
while driving . You can switch this function off
by moving the lever to position ® within 10
seconds of the afterwipe operation. The after
wipe function is reactivated the next time the
ignition is switched on.
Luggage compartment
General information
A WARNING
Read and follow the important safety pre
cautions on
<=> page 12 7, Stowing lug
gage.
Enlarging the luggage compartment
The backrests can be folded forward either
separately or together .
Fig. 79 Luggage compartment: release lever
Folding the backrest forward
• Pull the release lever in the direction of the
arrow to fold the backrest forward.
Folding the backrest back into the upright
position
• Fold the backrest back up again until it
latches securely <=>&_ .
A WARNING
The backrest must be securely latched so
objects cannot slide forward out of the
luggage compartment du ring sudden
braking.
(D Note
When folding the backrest forward, make
sure the rear safety belts are in the belt
guides so they do not become p inched in
the backrest lock and damaged. Other ob
jects should be removed from the rear bench seat to protect the backrest from
damage.
Seats and storage 67
Tie-downs
The luggage compartment is equipped with
four tie-down rings to secure luggage and
other items.
Fig. 80 Luggage compartment : tie-down s
• Secure objects using elast ic cords attached
to the t ie-downs
<=> fig. 80.
• Observe the safety notes <=> page 128.
Securing the ski sack
App lies to vehicles: wi th ski sack
Long objects such as skis or snowboards can
be transported in the ski sock.
Fig. 81 Luggage compartment: Secur ing the ski sack
Fig. 82 Rea r bench seat: securing the sk i sack
• Fold both backrests forward q page 67 .
68 Seats and storage
• Slide the ski sack from the luggage com
partment through the opening¢
A with
the zipper at the rear.
• To secu re the ski sack in the luggage com
partment, hang the hooks@¢
fig. 81 in
the rear tie -downs .
• Tighten the strap®¢
fig. 82 on the ski
sack to prevent the objects in the sack from
sliding .
& WARNING
-
- The ski sack is intended only for the
transportation of skis and other light ob
jects. To reduce the risk of serious per
sonal injury, never transport heavy or
pointed objects in the ski sack.
- When braking rapidly or during an acci
dent, the load could be displaced and
cause injury to occupants.
- Sharp edges on the load must be covered
for protection. Always fasten the belt
tightly around the sack and its contents
¢ fig . 82 .
-For safety reasons, do not transport
more than two pairs of skis in the ski
sack .
- You must secure the ski sack with the
strap after loading.
- Make sure that all objects you are trans
porting with the backrests folded for
ward are secured. Otherwise they could slide around during sudden braking ma
neuvers and cause injuries.
(i) Tips
- Never stow the ski sack away when it is
still wet or damp (for example, snow melting from skis) . Allow it to dry com
pletely before stowing it away .
- When transporting skis or snowboards, tighten the securing strap between the
bindings.
- Position skis in the ski sack with the
pointed ends facing the front and ski
poles with the pointed ends facing the
rear.
switching recirculation mode on when driving
through a tunnel or when sitting in traffic
c::>_& .
The IAU TOI button or I@ F RONT I button
switches recircu lation mode off .
IAUTO I Switching automatic mode on
Automatic mode mainta ins a constant tem
peratu re in side the vehi cle. Air temperature,
airflow and air distribution are controlled au
tomatically.
Adjusting the temperature
Temperatures between 60 °F (+16 °C) and
84
°F (+ 28 °C) can be set . Outside of this
range,
LO or HI will appear in the climate con
trol system display. At both of these settings,
the climate control system runs continuously
at maximum cooling or heating power. There
is no temperature regu lation.
~ Adjusting the airflow
You can adjust the airflow manually to suit
your needs . To have the airflow regulated au
tomatically, press the IAUTO ! button.
~Adjusting the air distribution
You can manually select the vents where the
a ir will flow. To have the air d istr ibution regu
lat ed automatically, press the
IAUTOI button.
~ Adjusting seat heating*
Pressing the button switches the seat heating
on at the highest sett ing (level 3). The LEDs
indicate the temperature leve l. To reduce the
temperature, press the button again. To
switch the seat heating off , press the button
repeatedly until the LE D turns off.
After 10 minutes, the seat heating automati
cally switches from level 3 to level 2.
[ill Adjusting seat ventilation*
Pressing the button switches the seat ventila
tion on at the highest setting (level 3) . The
LE Ds ind icate the ventilat ion level. To reduce
the ventilation leve l, press the button aga in.
To switch the seat ventilat ion off, press the
button repeatedly until the LED turns off.
Warm and cold 71
l F RON T I Switch the defroster on/off
The w indshield and side windows are defrost
ed or cleared of condensation as quickly as
possible . The maximum amount of air flows
main ly from the vents below the windshield.
Recirc ulation mode switches off. The tempera
ture should be set to 72
°F (22 °() or higher.
The temperature is controlled automatically.
The
! AUTO I button switches the defroster off.
lliil R EAR ! Switching rear window heater
on/off
The rear window heater on ly operates when
the engine is running .
It switches off auto
matically after a few minutes, depending on
the outside temperature.
To prevent the rear window heater from
switching off automatically, press and hold
the
l oo REARI button for more than 2 seconds.
This remains stored until the ign ition is
switched off .
Air vents
You can open and close the center and rear air
vents using the thumbwheels . The levers ad
just the direction of the airflow from the
vents.
In vehicles with a 3-zone deluxe automatic cli
mate control system*, you can adjust the air
temperature in the rear by turn ing the thumb
whee l toward the red side to make it warmer
or toward the b lue side to make it cooler .
A WARNING
-Do not use the recirculation for extended
periods of time. The windows could fog
up since no fresh air can enter the vehi
cle. If the windows fog up, press the air
recircu lation button again immediately
to switch off the air recirc ulation func
tion or se lect defrost.
- Individuals with reduced sensitivity to
pain or temperature could develop burns
when using the seat heating function. To
reduce the risk of injury, these indiv idu
als should not use seat heating.
84 On th e road
Presetting your speed
You can preset your desired speed while the
vehicle is not moving .
.,. Switch on the ignition .
.,. Pull lever into pos ition
(D q page 83,
fig . 94 .
... Press the lever in the 0 or 0 direction to
i ncrease o r decrease yo ur speed .
.,. Re lease the lever to save that speed.
This funct ion makes it possible, for example,
to save the speed yo u want before driving on
the highway . Once on the hig hway, activate
the cruise cont ro l by pull ing the leve r towa rd
(D .
Switching off
Temp orar y de activation
.,. Press the bra ke peda l, or
... Press the lever into position @ (not clicked
into place)
q page 83, fig . 94, or
... Drive for longer than 5 minutes at more
than 6 mph (10 km/h) above the stored
speed.
Sw it c hing off comp letely
... Press lever into position @ (clicked into
place), or
.,. Switch the ign ition off.
The speed yo u saved wi ll be retained if the
cruise control has been switched off tempora
rily. To resume the saved speed, let up on the
brake and pull the lever to pos ition
(D .
Sw itching the ignition off erases the saved
speed.
A WARNING
You should only return to the saved speed
if it is not too fast for the current traffic
conditions -risk of an accident!
92 Transmi ssion
The se lector lever can only be moved from the
P position if the key is in the lock and the igni
tion is sw itched on. If the power supply fails
(for example, the battery is discharged) and
the vehicle must be pushed or towed, move
the selector lever to the N pos ition first using
the emergency release .
Audi adaptive cruise control and braking guard 93
Audi adaptive cruise
control and braking
guard
Introduction
App lies to vehicles: with Audi adaptive cruise co ntrol
The adaptive cruise control system assists the
driver by regu lating vehicle speed and helping
to maintain a set distance to the vehicle
ahead, within the limits of the system . If the
system detects a moving vehicle up ahead,
adaptive cruise control can brake and then ac
celerate your vehicle . This he lps to make driv
ing more comfortable on long highway
stretches.
The braking guard system can warn you about
an impending collision and initiate braking
maneuvers ¢
page 99.
Adaptive cruise control and braking guard
have technical limitations that you must
know, so please read this section carefully, un
derstand how the system works and use them properly at all times.
General information
General information
Applies to vehicles: with Audi adaptive cruise control
Fig. 103 Front of the vehicle: Position of radar sensor
The area that contains the radar sensor
¢
fig. 103 must never be covered by stickers
or other objects or obstructed with dirt, in
sects, snow or ice that will interfere with the
adaptive cruise control system and braking
guard. For information on cleaning, refer to
¢
page 195. The same applies for any modifi
cations made in the front area . The
function of the adaptive cruise control
system and braking guard is limited under
some cond itions:
- Objects can only be detected when they are
within sensor range
.:!>page 95, fig. 106.
-The system has a limited ability to detect
objects that are a short distance ahead, off
to the side of your vehicle or moving into
your lane.
- Some kinds of vehicles are hard to detect;
for examp le motorcycles, vehicles with high
ground clearance or overhanging loads may
be detected when it is too late or they may
not be detected at all.
- When driving through curves¢
page 94.
-Stationary objects¢ page 94.
A WARNING
-Always pay attention to traffic when adap-
tive cruise control is switched on and brak ing guard is active. As the dr iver, you are
still respons ible for start ing and for main
tain ing speed and distance to other ob
jects. Braking guard is used to assist you .
The driver must always take action to avoid
a col lision. The driver is always responsible
for braking at the correct time.
- Im proper use of adaptive cruise con trol
can cause collisions, other accidents and
serious personal inj ury .
- Never let the comfort and convenience
that adaptive cruise control and braking
guard offer distract you from the need to
be alert to traffic conditio ns and the
need to remain in full control of your ve
hicle at all times,
- Always remember that the adaptive
cru ise control and brak ing guard have
limits -they will not slow the vehicle
down or maintain the set distance when
you drive towards an obstacle or some
thing on or near the road that is not
moving, such as vehicles stopped in a
traffic jam, a stalled or disabled vehicle.
If registered by the radar sensor, vehicles
or obstacles that are not moving can
trigger a collision warning and if .,.
Audi adaptive cruise control and braking guard 95
Audi adaptive cruise
control
Description
A pp lies to vehicles: with Audi adaptive cruise control
Fig. 106 Detect ion range
What can Audi adaptive cruise control do?
The adaptive cruise control works in conjunc
tion with a radar sensor installed in the front
of the vehicle ¢
page 93, fig . 103, which is
subject to designated sys tem limits
¢
page 95. Stationary objects are disregard
ed .
On open roads w ith no traffic, adaptive cruise
control wo rks like a regular cruise control sys
tem. The stored speed is maintained. When
approaching a moving vehicle detected up
ahead, the adaptive cruise control system au
tomatically slows down to match that vehi
cle's speed and then maintains the distance
that the driver previously stored. As soon as
the system does not detect a vehicle up
ahead, adaptive cruise control accelerates back up to the stored speed.
Which functions can be controlled?
When you switch adaptive cruise control on,
you can set the current speed as the "control speed" ¢
page 95, Switching on and off.
When driving, you can stop cruise control
¢
page 97 or change the speed¢ page 96
at any time .
You can a lso set the distance to the object
ahead and set the adaptive cruise control driv ing program
¢ page 97.
Switching on and off
Applies to vehicles: with Aud i adap tive crui se contro l
Fig. 107 Selecto r lever : switch ing on/off
Fig . 108 Instru men t cluster: Audi adaptive c ru ise con
trol
You can set any speed between 20 mph and
95 mph (30 and 150 km/h).
Ind icator lamps and messages in the instru
ment cluster disp lay inform you about the cur
rent system status and settings.
Switching Audi adaptive cruise control on
.. Pull the lever toward you into position (D
¢ fig. 107. ACC standby appears in the in
strument cluster display.
Setting the speed and activating regulation
.. To set the current speed, press the ISETI but-
ton ¢
page 11, fig. 4. The set speed is ll-