2014 Alfa Romeo 4C open bonnet

.
REAR LIGHTS
❒Bulb types ..........................................120
❒ Bulb replacement ................................118
LUGGAGE COMPARTMENT /
BONNET
❒ Opening/closing .................................. 38
ENGINE
❒Checking levels ...................................139
❒ Technical data .....................................157
FUEL CAP
❒Opening/closing .................................. 56
2
A0L0121
6
GRAPHICAL INDEX
24-9-2013 11:49 Pagina 6

The restoration procedure must be
performed as described below with the
doors closed:
❒completely open the driver's door
window keeping the operating button
pressed for at least three seconds
after the (lower) end of travel position
is reached;
❒ completely raise the driver side
window and hold the button down for
at least 3 seconds once the (upper)
end of travel position has been
reached;
❒ proceed in the same way as
described in points 1 and 2 for the
passenger side door;
❒ make sure that the initialisation is
correct by checking that the windows
work automatically.
WARNING
20) Incorrect use of the electric
windows may be dangerous.
Before and during their operation
ensure that passengers are not
at risk of injury from the moving
glass, either through personal
objects getting caught in the
mechanism or by being hit by it
directly. When leaving the car,
always remove the key from the
ignition to prevent accidental
operation of the electric windows
from being a hazard for those
still on board.
LUGGAGE
COMPARTMENT /
BONNET
21)
OPENING
IMPORTANT During normal car
operation, the luggage compartment
can reach temperatures above 65°C.
Pay attention when transporting objects
that may be damaged at such
temperatures. Do not keep aerosol
cans in the car: danger of explosion.
Aerosol cans must not be exposed to
temperatures above 50°C.
Procedure
22) 23)
❒with driver side door open, pull lever
A fig. 41, located at the point
illustrated in the figure;41
A0L0037
38
GETTING TO KNOW YOUR CAR
24-9-2013 11:49 Pagina 38

❒raise the tailgate and release
supporting rod B fig. 42 from its
locking device C;
❒ insert the end of the rod in housing D
fig. 43, making sure that the rod
engages in the smallest hole of the
retaining clip. Care must be taken to
keep the tailgate raised until the
rod is fixed in the correct position.
24)
IMPORTANT Maintain a tight grip on
the tailgate when raising, in order to
prevent any external occurrence (e.g. a
gust of wind) from suddenly opening
the tailgate to end of travel. Additionally,
in order to prevent any damage to the
car or broken windows, do not force
the tailgate beyond the opening
position necessary to secure the
supporting rod B in the hole of the
retaining clip.
CLOSING
Procedure
25)
❒hold the tailgate up with one hand
and use the other to remove rod B
fig. 42 from housing D fig. 43 and
reinsert it in its locking device C fig.
42;
❒ lower the bonnet to approximately 20
centimetres from the engine
compartment and let it drop. Make
sure that the bonnet is completely
closed and not only fastened in
safety position by trying to open it. If
it is not completely closed, do not
press the bonnet down, but raise it
and repeat the procedure.
IMPORTANT Always check that the
tailgate is closed correctly to prevent it
from opening while the car is travelling.
WARNING
21) The maximum permitted load in the luggage compartment, in
addition to the kits provided, is
15 kg.
22) When accessing the rear luggage compartment, take care
with parts that may be hot, owing
to the adjacent engine
compartment. Danger of serious
burns.
23) Perform these operations only with car stationary.
24) The tailgate may drop suddenly if the supporting rod is not
positioned correctly.
25) For safety reasons, the tailgate must always be closed properly
while the car is travelling.
Therefore, always make sure that
the tailgate is closed properly
and that the lock is engaged. If
you realise during travel that the
lock is not fully engaged, stop
immediately and close the tailgate
in the correct manner.
42
A0L0038
43
A0L0039
39
24-9-2013 11:49 Pagina 39

ENGINE OIL
Check that the oil level is between the
MIN and MAX marks on the dipstick
A fig. 110.
For this check, take out the dipstick
from its seat, clean it with a lint-free
cloth, reinsert the dipstick; take it out
again and check the oil level.
116)
If the oil level is near or under the MIN
mark, add oil through the filler B fig.
110 until it reaches the MAX mark.
20)
Take out the engine oil dipstick A, clean
it with a lint-free cloth and reinsert it.
Extract the engine oil dipstick again and
check that the level is between the
MIN and MAX marks on the dipstick.
116)
The range between the MIN and MAX
levels corresponds to approximately
1 litre of oil.
Engine oil consumption
21)
3)
The maximum engine oil consumption
is usually 400 grams every 1,000 km.
When the car is new, the engine needs
to run in, therefore the engine oil
consumption can only be considered
stabilised after the first 5,000 - 6,000
km.IMPORTANT After adding or changing
the oil, let the engine run for a few
seconds and wait a few minutes after
stopping it before you check the level.
ENGINE COOLANT
22)
117)
The coolant level must be checked
when the engine is cold and must
range between the MIN and MAX
marks on the reservoir.
If the level is too low, unscrew reservoir
plug C fig. 110 and add the fluid
described in the "Fluids and lubricants"
paragraph of the "Technical
Specifications" chapter.
WINDSCREEN WASHER
FLUID
118) 119)
To check the windscreen washer fluid
level, proceed as follows:
❒
to avoid any interference during the
procedure, lift the windscreen wiper
blade according to the "Windscreen
wiper" paragraph in the
"Maintenance and care" chapter;
❒ loosen the 4 self-tapping screws A
fig. 112 using the supplied
screwdriver. Remove the bonnet
grille;
❒ release the plug from the opening; ❒
leaving the plug close to the opening,
put a finger on the central hole B fig.
113 in the plug and remove it: the
level can be seen on the control pipe
C fig. 114 due to capillarity;
❒ after the check, reinsert the plug B
with the control pipe C in the initial
position;
❒ reposition the bonnet grille and
tighten the 4 self-tapping screws A.
WARNING Re-close the plug holding it
horizontally (not directed towards the
bonnet) to prevent the opening tang
from remaining locked in a position
difficult to reach.
It is recommended to check the
windscreen washer fluid regularly, in
particular in driving conditions needing
a heavier use of the windscreen washer.
112
A0L0130
141
24-9-2013 11:50 Pagina 141

If the level is not sufficient, namely if
there is no fluid inside the pipe, proceed
as follows:
❒to avoid any interference during the
procedure, lift the windscreen wiper
blade according to the "Windscreen
wiper" paragraph in the
"Maintenance and care" chapter;
❒ loosen the 4 self-tapping screws A
fig. 112 using the supplied
screwdriver. Remove the bonnet
grille;
❒ take the white funnel D fig. 115 for
topping up the windscreen washer
fluid/fuel and its extension pipe from
the service kit in the luggage
compartment;
❒ take out the plug B fig. 113 with the
fluid control pipe through the bonnet
opening on the grille;
❒ introduce the funnel D fig. 115 and its
extension pipe in the reservoir neck
and top up;
❒ after topping up, remove the funnel D
with the extension pipe;
❒ refit the plug B with the dipstick;
❒ reposition the bonnet grille and
tighten the 4 self-tapping screws A. BRAKE FLUID
120) 121)23) 24)
To check the brake fluid level, proceed
as follows:
❒
loosen the 2 self-tapping screws E
fig. 116 and remove the protection
panel;
❒ check that the fluid is at the max.
level.
❒ after checking, reposition the
protection panel and tighten the 2
self-tapping screws E.
If the fluid level in the reservoir is not
sufficient, proceed as follows:
❒ take the black funnel for topping up
the brake fluid and its extension
pipe from the service kit in the
luggage compartment;
113
A0L0131
114
A0L0147
115
A0L0148
142
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 142

❒loosen the reservoir plug and
introduce the funnel F fig. 117 with
the extension pipe in the reservoir
inlet;
❒ after topping up, remove the funnel F
with the extension pipe;
❒ tighten the reservoir plug;
❒ reposition the protection panel and
tighten the 2 self-tapping screws E.
WARNING Be very careful while
removing the plug from the opening to
prevent the plug from falling inside
the vehicle body.
IMPORTANT
19) Be careful not to confuse the various types of fluids while
topping up: they are not
compatible with each other!
Topping up with an unsuitable
fluid could severely damage your
vehicle.
20) The oil level should never exceed the MAX mark.
21) Do not add oil with specifications other than those of the oil already
in the engine. 22) PARAFLU
UP
anti-freeze fluid is
used in the engine cooling
system; use the same fluid type as
that already in the cooling system
when topping up. PARAFLU
UP
may not be mixed with other types
of anti-freeze fluids. If topping up
with an unsuitable product, under
no circumstances start the engine
and contact a dedicated Alfa
Romeo Dealership.
23) Avoid allowing brake fluid, which is extremely corrosive, to come
into contact with painted areas.
Should it happen, immediately
wash with water.
24) Be very careful while topping up the brake fluid, as it could drip
from the extension pipe inside the
vehicle under-bonnet and on
parts of the body and windscreen,
corroding and damaging them.
Adopt suitable protection (e.g
absorbing paper) to reduce this
risk as much as possible.
116
A0L0149
117
A0L0160
143
24-9-2013 11:50 Pagina 143

INDEX
ABS .............................................. 42
– System intervention ................... 42
Air cleaner ...................................... 145
Alarm ............................................. 13"Alfa DNA" system ........................ 45
– "All Weather" mode ................... 47
– Driving modes ........................... 46
– “Dynamic” mode ....................... 46
– "Natural" mode.......................... 46
– “Race” mode............................. 46Alfa Romeo Code system ............. 10
Ashtray .......................................... 35
ASR system (AntiSlip Regulation) ... 42Backrest pocket ........................... 35
Battery ........................................... 145 – advice for extending lifetime ...... 145
– replacement .............................. 145
Battery (recharging) ........................ 129
Body versions ................................ 156
Bodywork – body codes ............................... 156
– maintenance ............................. 150
– protection against atmospheric agents................... 149
– warranty .................................... 149
Bonnet – Closing ...................................... 39 – Opening .................................... 38
Brakes ........................................... 160 – brake fluid level.......................... 142
bulb replacement.................... 123-124
Bulb replacement – exterior lights ............................. 122
– interior lights .............................. 125
Bulbs
– types of bulbs ........................... 120
Car inactivity ................................. 111
Carrying children safely .................. 93
CBC (Cornering Brake Control) system ......................................... 42
Central locking ............................... 32
Changing a bulb............................. 118 – General instructions................... 118
Cigar lighter.................................... 34
Cleaning and maintenance – bodywork .................................. 149
– car interior ................................. 151
– engine compartment ................. 150
– front headlights ......................... 150
– leather parts .............................. 152
– leather seats.............................. 151
– plastic and coated parts ............ 152
– seats and fabric parts ................ 151
– windows.................................... 150
Climate control ............................... 19 – Passenger compartment air diffusers .................................... 20 Climatic comfort ............................. 20
Clutch ............................................ 159
CO2 emissions............................... 175
Conditions of use ........................... 110
Control buttons .............................. 62
Control panel and instruments ....... 60
Controls ......................................... 32
Cruise Control ................................ 29
Cup holder ..................................... 35
Daytime running lights (DRL) ......... 27
Dimensions .................................... 167
Dipped beam headlights – bulb replacement ...................... 122
Direction indicators ........................ 27 – bulb replacement ...................... 122
– “Lane change” function ............. 27
Door mirrors – Door mirrors .............................. 18
Doors ............................................. 36 – Central door locking/unlocking ...................... 36
Driver's side front airbag ................ 97
Driving style.................................... 110
DTC (Drag Torque Control) system ......................................... 42EBD system .................................. 42
Electric windows ............................ 37 – Controls .................................... 37"Electronic Q2" system ("E-Q2") .... 44
INDEX

Engine codes ................................ 156
Engine compartment – checking levels .......................... 139
– washing .................................... 150
Engine coolant indicator ................. 62
Engine – engine cooling system fluid level........................................... 141
– identification codes ................... 156
– marking ..................................... 155
– technical data............................ 157
Engine oil – consumption ............................. 141
– level check ................................ 141
EOBD system ................................ 48
ESC (Electronic Stability Control) system ......................................... 41
Exterior lights ................................. 26
Extinguisher ................................... 35Filling the tank ............................... 56
Fitting "Universal" child restraint system ......................................... 94
Fix&Go automatic kit ...................... 115
Flashing ......................................... 27
Fluids and lubricants (specifications) ............................. 171"Follow Me Home" device ............. 28Front airbags................................. 97
Fuel consumption .......................... 174
Fuel cut-off system......................... 32 Fuel level gauge ............................. 62
Fuel supply..................................... 158
Fuses (replacement) ....................... 126
Gear Shift Indicator ....................... 62Handbrake.................................... 103
Hazard warning lights..................... 32
HBA system ................................... 43
Headlights...................................... 40 – Adjusting the headlights abroad ...................................... 40
– bulb replacement ...................... 122
– Light beam direction.................. 40
Heating and ventilation ................... 21
Hill Holder system .......................... 43Identification data – bodywork paint plate ................. 154
– chassis marking ........................ 154
– engine marking.......................... 155
Identification data – identification data plate.............. 154
Ignition switch ................................ 14 – Steering lock ............................. 15
Installing electrical/electronic devices ........................................ 49
Instrument panel ............................ 60
Interior fittings ................................ 33
Interiors (cleaning) .......................... 151Light clusters – front light clusters (changing a
bulb).......................................... 122
– rear light clusters (changing a bulb).......................................... 123
Lubricants (specifications) .............. 171
Luggage compartment / Bonnet .... 38
Luggage compartment – Opening .................................... 38
Luggage compartment roof light – bulb replacement ...................... 125
M
ain beam headlights .................. 27
– bulb replacement ...................... 122
Maintenance and care – heavy-duty use of the car .......... 138
– periodic checks ......................... 138
– scheduled servicing ................... 134
– scheduled servicing plan ........... 135
Manual climate control ................... 24
Menu options ................................. 64
Number plate lights
– bulb replacement ...................... 124O
ddments pocket......................... 34
On-board instruments – display....................................... 60
– engine coolant temperature indicator .................................... 62
– fuel level gauge ......................... 62
– On-board instruments ............... 60
– rev counter ................................ 62