2014 Alfa Romeo 4C ignition

RECHARGING THE
BATTERYIMPORTANT The battery recharging
procedure is given as information only.
To carry out this operation contact
the dedicated Alfa Romeo Dealership.
IMPORTANT After turning the ignition
key to STOP, wait at least one minute
before disconnecting the electrical
supply from the battery.
We advise you to use a battery charger
with rated recharging voltage of 12 V
and maximum current 15 A, for a
period from 12–24 hours. Charging for
a longer time may damage the battery.
To recharge, proceed as follows:
❒disconnect the negative battery
terminal;
❒ connect the charger cables to the
battery terminals, observing the
polarity;
❒ turn on the charger;
❒ when it is recharged, turn the charger
off before disconnecting it from the
battery;
❒ reconnect the negative battery
terminal.
RAISING THE CARIf raising the car is necessary, contact a
dedicated Alfa Romeo Dealership,
who will be equipped with suitable arm
or workshop lifts, in addition to the
specific equipment necessary.
It is however possible to use suitable
lowered hydraulic jacks to raise the car
if necessary.
The car lifting points are marked on the
side skirts with the
symbols (see
points illustrated in fig. 106).
The correct support points for raising
the front and rear part of the car are
illustrated in fig. 107 and fig. 108. IMPORTANT When positioning the car
on the arm lift, remember that the
power unit is located at the rear end,
with consequent impact on weight
distribution. Therefore, the shorter arms
must support the rear end, and the
longer arms support the front end.
16) 17)
106
A0L0029
107 - Rear area
A0L0128
108 - Front area
A0L0127
129
24-9-2013 11:50 Pagina 129

IMPORTANT
16) Be careful to position the liftarms correctly at the points
illustrated, in order to prevent
damage to the carbon fibre
chassis and the bodywork
components.
17) To avoid damage to the carbon fibre chassis, the car cannot be
raised with standard hydraulic
jacks, only with suitable lowered
hydraulic jacks. Contact a
dedicated Alfa Romeo Dealership.
TOWING THE CAR
18)
The tow hook provided with the car is
located in the tool box in the luggage
compartment.
ATTACHING THE TOW
HOOK
Take tow hook A and tighten it fully
onto the threaded pin fig. 109.
110) 111) 112)
IMPORTANT
18) The tow hook attachment is onlyavailable at the front end of the
car.
WARNING
110) Before towing, turn the ignitionkey to MAR-ON and then to STOP
without removing it. The steering
column will automatically lock
when the key is removed and the
wheels cannot be steered. Also
check that the gearbox/
transmission is in neutral (N).
111) When towing, remember that the assistance of the brake servo
is absent. Consequently, more
force is required at the pedal
in order to brake. Do not
use flexible cables when towing
and avoid jerky movements. Make
sure not to damage parts in
contact with the car while towing.
When towing the car, you must
comply with all specific traffic
regulations, both in terms of the
towing device and behaviour
on the road. Do not start the
engine while towing the car.
Before tightening the ring, clean
the threaded housing thoroughly.
Make sure that the ring is fully
screwed into the housing before
towing the car.
109
A0L0107
130
IN AN EMERGENCY
24-9-2013 11:50 Pagina 130

WINDSCREEN
WIPERIt is advisable to replace the blade
about once a year.
131)
A few simple precautions can reduce
the possibility of damage to the blade:
❒if the temperature falls below zero,
make sure that ice has not frozen
the rubber to the glass. Use an
antifreeze product to release it if
required;
❒ remove any snow from the glass;
❒ do not operate the windscreen wiper
on dry glass.
IMPORTANT Do not lift the arm of the
windscreen wiper when it is in its initial
rest position. Refer to the following
instructions to lift the windscreen wiper
blade correctly.
Lifting blade
If it is necessary to lift the blade from
the windscreen (e.g. in the event of
snow or if the blade needs
replacement) proceed as follows:
❒ turn ring nut A fig. 120 to
(wiper
off);
❒ turn the ignition key to MAR-ON and
then to STOP; ❒
after turning the ignition key to STOP,
within 2 minutes move the right stalk
upwards, into unstable ("anti-panic")
position, for at least half a second.
The windscreen wiper then executes
part of a stroke; at each command,
approximately 1/3 of a normal wiper
stroke is triggered.
❒ the previous operation can be
repeated up to 3 times, in order to
move the blade to the most suitable
position;
❒ lift the blade from the windscreen and
proceed with the required operation;
❒ lower the blade, bringing it into
contact with the windscreen;
❒ bring the blade to the initial rest
position, turning the ignition key
to MAR-ON.
26)
Replacing the
windscreen wiper blade
Proceed as follows:
❒lift the windscreen wiper blade,
following the instructions given
preciously;
❒ press tab A fig. 121 of the
attachment spring and remove the
blade from the arm;
❒ fit the new blade, inserting the tab in
the dedicated housing in the arm
and checking that it is locked;
❒ lower the wiper arm onto the
windscreen.
120
A0L0021
121
A0L0086
148
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 148

PRESERVING THE
BODYWORK
Paintwork
5)
27) 28)
Touch up abrasions and scratches
immediately.
Maintenance of paintwork consists of
washing the car: the frequency
depends on the conditions and
environment where the car is used. For
example, in highly polluted areas, or if
the roads are spread with salt, it is
advisable to wash the car more
frequently.
To correctly wash the car, proceed as
follows:
❒if high pressure jets or cleaners are
used to wash the car, keep a
distance of at least 40 cm from the
bodywork to avoid damage or
alteration. It should be remembered
that the build up of water can
damage the car over a period of
time;
❒ wash the bodywork using a low
pressure jet of water;
❒ wipe a sponge with a slightly soapy
solution over the bodywork,
frequently rinsing the sponge;
❒ rinse well with water and dry with a
jet of air or a chamois leather. Dry the less visible parts (e.g. door
frames, bonnet, headlight frames, etc.)
with special care, as water may
stagnate more easily in these areas.
The car should not be taken to a closed
area immediately, but left outside so
that residual water can evaporate.
Do not wash the car after it has been
left in the sun or with the tailgate hot:
this may alter the shine of the
paintwork.
Exterior plastic parts must be cleaned
in the same way as the rest of the car.
Avoid parking under trees as much
as possible; the resin from trees dulls
the paintwork.
IMPORTANT Bird droppings must be
washed off immediately and thoroughly
as the acid they contain is particularly
aggressive.
Windows
Use specific detergents and clean
cloths to prevent scratching or altering
the transparency.
Front headlights
Use a soft cloth soaked in water and
detergent for washing cars.
IMPORTANT Never use aromatic
substances (e.g. petrol) or ketenes (e.g.
acetone) for cleaning the plastic lenses
of the front headlights.
Engine compartment
At the end of the winter the engine
compartment should be carefully
washed, without directing the
jet against any electronic control unit.
Have this operation performed at a
specialised workshop.
IMPORTANT The washing should take
place with the engine cold and the
ignition key in the STOP position. After
the washing operation, make sure
that the various protections (e.g. rubber
caps and guards) have not been
removed or damaged.
150
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 150

Engine codes ................................ 156
Engine compartment – checking levels .......................... 139
– washing .................................... 150
Engine coolant indicator ................. 62
Engine – engine cooling system fluid level........................................... 141
– identification codes ................... 156
– marking ..................................... 155
– technical data............................ 157
Engine oil – consumption ............................. 141
– level check ................................ 141
EOBD system ................................ 48
ESC (Electronic Stability Control) system ......................................... 41
Exterior lights ................................. 26
Extinguisher ................................... 35Filling the tank ............................... 56
Fitting "Universal" child restraint system ......................................... 94
Fix&Go automatic kit ...................... 115
Flashing ......................................... 27
Fluids and lubricants (specifications) ............................. 171"Follow Me Home" device ............. 28Front airbags................................. 97
Fuel consumption .......................... 174
Fuel cut-off system......................... 32 Fuel level gauge ............................. 62
Fuel supply..................................... 158
Fuses (replacement) ....................... 126
Gear Shift Indicator ....................... 62Handbrake.................................... 103
Hazard warning lights..................... 32
HBA system ................................... 43
Headlights...................................... 40 – Adjusting the headlights abroad ...................................... 40
– bulb replacement ...................... 122
– Light beam direction.................. 40
Heating and ventilation ................... 21
Hill Holder system .......................... 43Identification data – bodywork paint plate ................. 154
– chassis marking ........................ 154
– engine marking.......................... 155
Identification data – identification data plate.............. 154
Ignition switch ................................ 14 – Steering lock ............................. 15
Installing electrical/electronic devices ........................................ 49
Instrument panel ............................ 60
Interior fittings ................................ 33
Interiors (cleaning) .......................... 151Light clusters – front light clusters (changing a
bulb).......................................... 122
– rear light clusters (changing a bulb).......................................... 123
Lubricants (specifications) .............. 171
Luggage compartment / Bonnet .... 38
Luggage compartment – Opening .................................... 38
Luggage compartment roof light – bulb replacement ...................... 125
M
ain beam headlights .................. 27
– bulb replacement ...................... 122
Maintenance and care – heavy-duty use of the car .......... 138
– periodic checks ......................... 138
– scheduled servicing ................... 134
– scheduled servicing plan ........... 135
Manual climate control ................... 24
Menu options ................................. 64
Number plate lights
– bulb replacement ...................... 124O
ddments pocket......................... 34
On-board instruments – display....................................... 60
– engine coolant temperature indicator .................................... 62
– fuel level gauge ......................... 62
– On-board instruments ............... 60
– rev counter ................................ 62