2014.5 Citroen BERLINGO MULTISPACE RHD display

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
40
The alert is maintained until the tyre or tyres concerned is
reinflated,  repaired   or   replaced.
The spare wheel (space-saver type or
a
 
steel   rim)   does   not   have   a   sensor.
Operating faultu
nder-inflation alert
The loss of pressure detected
does not always lead to visible
deformation
 
of
 
the
 
tyre.
 
Do
 
not
 
rely
 
on

  just   a   visual   check.The alert is given by the fixed illumination   of   this   warning   lamp,  
accompanied

  by   an   audible   signal,  
and

  depending   on   equipment,   the  
display

  of   a   message.The flashing and then fixed  illumination   of   the  
under-inflation

  warning  
lamp

  accompanied   by   the  
illu

mination   of   the   "Service"   warning  
lamp,

 
and   depending   on   equipment,  
the

 
display   of   a   message   indicates   a  
fault

 
with   the   system.
In
 
this
 
case,   monitoring   of   the   tyre  
pressures

  is   not   assured.
In
 
the
 
event
 
of
 
a
 
problem
 
on
 
one
 
of
 
the

 
tyres,
 
the
 
symbol
 
or
 
the
 
message
 
appears,

 
according
 
to
 
equipment,
 
to
 
identify

 
it.
-

Reduce speed, avoid sudden
steering

 
movements
 
or
 
harsh
 
brake
 
applications.
-

 
Stop

 
as
 
soon
 
as
 
it
 
is
 
safe
 
to
 
do
 
so.
-

In the event of a puncture, use
the

 
temporary
 
puncture
 
repair
 
kit
 
or the spare wheel (according to
equipment),
or
-

 
if

 
you
 
have
 
a
 
compressor,
 
the
 
one
 
in

 
the
 
temporary
 
puncture
 
repair
 
kit

 
for
 
example,
 
check
 
the
 
four
 
tyre
 
pressures when cold,
or
-

 
if

 
it
 
is
 
not
 
possible
 
to
 
check
 
the
 
tyre

 
pressures
 
at
 
the
 
time,
 
drive
 
carefully

 
at
 
reduced
 
speed. This alert is also displayed when
one
  or   more   wheels   is   not   fitted  
with

  a   sensor   (for   example,   a  
space-saver

  or   steel   spare   wheel).
Go
 
to
 
a   CITROËN   dealer   or   a   qualified  
workshop to

  have   the   system   checked  
or

, following the repair of a puncture, to
have
 
the   original   wheel,   equipped   with  
a

 
sensor,   refitted.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
41
SErVIc E I nd I c AtO r
This programmes service intervals according
  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each

  time   the   ignition   is   switched   on  
and for a few seconds, the spanner
flashes

  and   the   number   of   miles/
kilometres
  remaining   is   displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation

  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A
 

few   moments   after   the   ignition  
has been switched on, the spanner
indicating

  a   service   operation   comes  
on; the display for the total distance
recorder

  gives   (in   round   figures)   the  
distance

  remaining   before   the   next  
service.
The points at which a service is due
are

  calculated   from   the   last   indicator  
zero

  reset.
The point at which a service is due is
determined
  by   two   parameters:
-

the distance travelled,
-

 
the
  time   which   has   elapsed   since  
the

  last   service.
The
  distance   remaining   before   the  
next

  service   may   be   weighted   by  
the

  time   factor,   depending   on   the  
type

  of   driving. With the engine running the spanner
remains
  on   until   the   service   has   been  
carried

  out.
For BlueH
d i d iesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination   of   the   Service   warning  
lamp,

  on   switching   on   the   ignition.
Each
  time   the   ignition   is  
switched on and for a few
seconds, the spanner
flashes

  and   the   excess  
distance

  is   displayed.
For BlueH
d i d iesel versions, the
spanner
  can   also   come   on   early,  
according the level of deterioration
of

  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
Instruments and controls
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
42
trip recorder zero reset button
after this operation, if you wish
to   disconnect   the   battery,   lock  
the vehicle and wait for at least
five minutes,

  otherwise   the   zero   re-set  
will

 
not   be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates  
a
 
malfunction of the engine oil level


indicator.   Contact
 a

  CITROËN   dealer   or   a   qualified
 workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.
d
ipstick
A   =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero re-set
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
48
Going into engine StArt mode
The "EcO" warning lamp goes
  off   and   the   engine   starts:
- with a manual gearbox , when you
fully depress the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position  n and
the
  brake   pedal   released,   when  
you

  move   the   gear   lever   to  
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With
  a   manual   gearbox   in   STOP
 mode,

  if   a   gear   is   engaged   without  
fully depressing the clutch pedal, a
warning

  lamp   comes   on   or   a   message  
is

  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.Special cases: S
t
A
rt invoked
automatically
For   your   safety   and   comfort,   START
 
is  
invoked

  automatically   when:
-
you open the driver's door
,
-
you unfasten the driver's seat belt,
-
the speed of the vehicle exceeds
15
  mph   (25   km/h)   with   a   manual  
gearbox

  or   7   mph   (11   km/h)   with  
the

  6-speed   electronic   gearbox  
system,
-

 
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.In this case the

"E c O"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
t

his operation is perfectly normal.
deactivation
At any time, press the "EcO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp

 
coming   on   accompanied   by   a  
message

  in   the   screen.
If
 
the
 
system   has   been   deactivated  
in

 
STOP
 

mode,   the   engine   restarts  
immediately

.
Stop & Start

 57
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
cruISE cOntrOL "cruISE"
In order for it to be programmed or activated,  the   vehicle   speed   must   be  
greater

  than   25   mph   (40   km/h)   with   at  
least

  4th   gear   engaged. This cruise control shows the function
selection
  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:
Function selected,
display of the "Cruise
Control"   symbol.
Function deactivated,
OFF.
Function activated
Vehicle speed above
the   programmed  
speed, which is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
"This is the speed at which the driver
wishes
 
to
 
drive".
This
 
aid
 
to
 
driving
 
in
 
free-flowing
 
traffic

 
enables
 
the
 
vehicle
 
to
 
maintain
 
the

 
speed
 
programmed
 
by
 
the
 
driver,
 
unless

 
a
 
steep
 
gradient
 
makes
 
this
 
impossible.
Steering mounted controls
EASE OF uSE and cOMFOrt
4

60
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
However, pressing the pedal beyond
this  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
t

he operating actions may be
carried out when stationary, with the
engine running, or with the vehicle
moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:
SPEEd LIMItEr "LIMIt"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function deactivated,
last

  programmed  
speed -

OFF.
Function activated
Vehicle speed above
the
  programmed  
speed, which is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 
running while stationary or with the
vehicle

 
moving.
 
The

 
minimum
 
speed
 
which

 
can
 
be
 
programmed
 
is
 
20
 
mph
 
(30

 
km/h).
The speed of the vehicle responds
to the pressure of the driver's foot as
far as the accelerator pedal point of
resistance which indicates that the
programmed
 
speed
 
has
 
been
 
reached.
Steering mounted controls

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 65
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
dIGItAL AIr c O nd I t IO n I n G WI t H SEPA r At E SE tt I n GS
Automatic operation
AutO comfort programme
This   is   the   normal   air   conditioning  
system

  operating   mode.
d
river or passenger side comfort
value
The value indicated in the screen
corresponds   to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the A
ut
O

symbol
  is   displayed.
In accordance with the
comfort
  value   selected,  
the

  system   controls   the  
distribution,

  the   flow   and   the   intake  
of

  air   to   guarantee   comfort   and   a  
sufficient

  circulation   of   air   in   the  
passenger

  compartment.   No   further  
action

  on   your   part   is   required.
When the engine is cold, to prevent an
excessive diffusion of cold air, the air diffuser
will  reach   its   optimum   level   gradually.
For
  your   comfort,   the   settings   are   stored
 when the ignition is switched of

f and are
reinstated
  the   next   time   the   vehicle   is
 started.
The

  automatic   function   will   no   longer   be
 maintained

  if   you   change   a   setting   manually
 (AUT

O   is   cleared).
FOr tHE drIVEr And PASSEnGEr
Ventilation
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
66
Manual operation
You can, according to your
requirements,  make   a   different   selection from

  that   offered   by   the   system   by
 changing

  a   setting.  
The
  other   functions
 will

  still   be   controlled   automatically.
 Pressing the

A ut
O
button restores fully
automatic
  operation.
Air distribution
Pressing this button several
times
  in   succession   directs  
the

  air   flow   towards:
-

the windscreen,
-


the windscreen and footwells,
-


the footwells,
-


the side vents, central vents and
footwells,
-

 
the
  side   vents   and   central   vents.Air flow
Press the small fan button to
reduce
  the   flow   or   the   large
fan button to increase the
flow.
On
  the   display,   the   blades   of   the   fan   fill  
when

  the   flow   is   increased.
Switching the air
conditioning On / Off
Press this button, the A/
c
symbol
  is   displayed   and   the  
air

  conditioning   is   activated.
d
eactivating the system
Press
  the   air   flow   small fan
button
  until   the   fan   symbol  
disappears

  from   the   display.
This action deactivates all of the
system's
  functions,   with   the   exception  
of the air recirculation and rear screen
demisting

  (if   fitted   on   your   vehicle).  
Y

our   comfort   setting   is   no   longer  
maintained

  and   is   switched   off.Intake of exterior air / r
ecirculation of interior air
Press this button to
recirculate
  the   interior   air.  
The

  recirculation   symbol   is  
displayed.
Pressing the

large fan
button or the A
ut
O
button
reactivates
  the   system   with  
the values set before it was
deactivated.Recirculation prevents exterior odours


and
  smoke   from   entering   the   passenger
 compartment.

 
A
void   prolonged   operation
 in

  interior   air   recirculation   mode   (risk   of
 condensation,

  odour   and   humidity).
Pressing this button again activates the
intake
  of   exterior   air.
Pressing this button again switches off
the
  air   conditioning.
The ventilation outlet, located
in the glove box, diffuses cool
air (if the air conditioning is
on) regardless of the reference
temperature
  requested   in   the  
passenger

  compartment   and  
regardless

  of   the   exterior   temperature.
For
  your   comfort,   do   not   deactivate   the  
system

  for   long   periods.  
Ventilation