2014.5 Citroen BERLINGO MULTISPACE RHD display

 107
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
The audible and/or visual rear parking sensor  system   consists   of   four  
proximity

  sensors,   installed   in   the  
rear

  bumper.  
The
  sensors   detect   any  
obstacle

  which   enters   the   field:   person,  
vehicle, tree, fence, behind the vehicle
during

  the   manoeuvre.
Certain
  objects   detected   at   the  
beginning

  of   the   manoeuvre   will   no  
longer be detected at the end of the
manoeuvre

  due   to   the   blind   spots  
between

  and   below   the   sensors.  
Examples:

  stake,   roadworks   cone   or  
pavement

  post.
Engage reverse gear
r

EA
r
PA
r
KI
n
G SE
n
SO
r
S
display in the screen
Stop the assistance
Change to neutral.
An
 
audible
 
signal
 
confirms
 
the
 
activation

 
of
 
the
 
system
 
by
 
engaging
 
reverse

 
gear.
The
 
proximity
 
information
 
is
 
indicated
 
by

 
an
 
audible
 
signal
 
which
 
becomes
 
more

 
rapid
 
as
 
the
 
vehicle
 
approaches
 
the

 
obstacle.
 
When
 
the
 
distance
 
between the rear of the vehicle and
the

 
obstacle
 
is
 
less
 
than
 
approximately
 thirty
 
centimetres,
 
the
 
audible
 
signal
 becomes
 
continuous.
Parking sensors
SaFETY
5

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
150
range indicators
When switching on the ignition, an
indicator  gives   an   estimate   of   the  
distance that can be travelled with
your vehicle before engine starting
is

  automatically   prevented,   once   the  
vehicle starts using the reserve of a

dBlue
® or after a fault is detected with
the
 
SCR   system.
In
 
the
 
event   of   simultaneous   system  
fault and low a

dBlue
® level, the
shortest
 
range
 
is
 
the
 
one   displayed.
In the event of the risk
of non-starting related to a lack
of AdBlue
®
The engine start prevention
system   required   by   regulations   is  
activated

  automatically   once   the  
a
dBlue
® tank is empty.
range greater than 1 500 miles (2 400 km)
When the ignition is switched on, no
information   on   range   is   displayed  
automatically

  in   the   instrument   panel.
Pressing this button
displays the driving range
temporarily.
Above
  3   000   miles  
(5
  000   km),   the   value   is  
not

  specified. When switching on the ignition, the
UREA warning
  lamp   comes   on,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.:   "Top   up  
emissions

  additive:   Starting   prevented  
in

  900   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed

  every   150   miles   (300   km)  
until

  the   additive   tank   has   been  
topped-up.
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
r

emaining range between 350 and
1500 miles (600 and 2 400 km)
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
151
When switching on the ignition, the
SERVICE  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.   "Top   up  
emissions

  additive:   Starting   prevented  
in

  350   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed every 30 seconds until the
additive

  tank   has   been   topped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
o

therwise you will not be able to
restart
 
your
 
engine. When switching on the ignition, the
SERVICE
  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal  
and

  the   display   of   the   message  
"T

op   up   emissions   additive:   Starting  
prevented".
The

a dBlue
® tank is empty: the system required
 
by
 
regulations   prevents  
engine

 
starting. To be able to start the engine,
we
  recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
workshop

  for   the   top-up   required.   If  
you carry out the top-up yourself, it is
essential

  to   add   at   least   3.8   litres   of  
a dBlue
® to the tank.
r

emaining range between 0 and
350 miles (0 and 600 km) Breakdown related to a lack of
AdBlue
® additive
Refer   to   the   "Topping-up"   section.
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
152
In the event of a fault with
the the Scr emissions control
system
When switching on the ignition, the
URE
a , SERVICE and diagnostic
warning
  lamps   comes   on,   accompanied
 by an audible signal and the display of


a
  message   "Emissions   fault"   to   signal   a
 fault

  with   the   emissions   control   system.
If
  it   is   a   temporary   fault,   the   alert  
disappears once the exhaust gas
emissions

  return   to   normal.during an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
A  system   that   prevents   engine  starting
  is   activated   automatically  
from

  650   miles   (1   100   km)   after  
confirmation

  of   a   fault   with   the   SCR  
emissions

  control   system.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop   as   soon   as  
possible. In the event of the detection


of a fault
If   a   fault   with   the   SCR   system   is  
confirmed

  (after   30   miles   (50   km)  
covered

  with   the   permanent   display   of  
the

  message   signalling   a   fault),   when  
switching on the ignition, the SER

VICE
and
  engine   diagnostic   warning   lamps  
come

  on   and   the   UREA
 
warning   lamp  
flashes,

  accompanied   by   an   audible  
signal

  and   the   display   of   a   message  
(e.g.:

  "Emissions   fault:   Starting  
prevented

  in   150   miles")   indicating   the  
remaining

  range   express   in   miles   or  
kilometres.
While

  driving,   the   message   is  
displayed every 30 seconds while the
fault

  with   the   SCR   system   persists.
You should go to a CITR
o Ë n dealer
or
  a   qualified   workshop   as   soon   as  
possible.
o

therwise, you will not be able to
restart
  your   engine.
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
153
Every time the ignition is switched on, the SERVICE and engine diagnostic
warning
  lamps   come   on   and   the   UREA
 warning

  lamp   flashes,   accompanied  
by an audible signal and the display of
the

  message   "Emissions   fault:   Starting  
prevented".
Y

ou have exceeded the authorised
driving
  limit:   the   starting  
prevention

  system   inhibits   engine  
starting.
T

o be able to start the engine, you
must
  call   on   a   CITROËN   dealer   or   a  
qualified

  workshop.
Starting prevented
The a dBlue
® additive freezes at
temperatures   below   around   -11°C.
The
 
SCR
 
system   includes   a   heater   for  
the

a
dBlue
® tank.
In
 
exceptional   circumstances   (vehicle  
kept

 
for
 
a
 
long   period   at   temperatures  
that

 
are
 
constantly   below   -15°C),   an  
emissions

 
control   system   fault   alert  
may

 
be
 
related   to   freezing   of   the  
a
dBlue
® in your vehicle.
Park
 
your   vehicle   in   a   warmer   area   for  
a

 
few
 
hours   until   the   additive   becomes  
liquid

 
again.
The
 
emissions   alert   does   not   go   off  
immediately

,   it   will   occur   after   several  
mile

 
of
 
running.
Freezing of the AdBlue
® additive
adBlue® additive
CHECkS
7

01
10.4
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Select:
- 
the
  next   lower   /   higher   radio  
frequency

  automatically.
-
 
the
  previous   /   next   CD   track,   MP3  
track

  or   media.
-
 
the
  left   /   right   of   the   screen   when   a  
menu

  is   displayed.
Move
  left   /   right   in   "Move the map"   mode.a
bandon the current
operation, up one level
in
 
the
 
menu.
Long
 
press:
 
return
 
to
 
the

 
permanent
 
display.
o

pen the
"Configuration "
 
menu.
Long
 
press:
 
access
 
to the GPS coverage
and the navigation
demonstration

 
mode.o
pen the "Traffic
information"
 
menu
 
and display the current
traffic

 
alerts. Select:
-
 
the
  previous/next   line   in   a   list   or   menu.
-  
the
  previous   /   next   media   folder.
-  
step
  by   step   selection   of   the   previous/
next   radio   frequency.
-  
the
  previous   /   next   MP3   folder.
Move   up/down,   in   "
Move the map"   mode.
FIrSt StEPS
access to the
" n avigation - guidance "
menu
  and   display   the  
recent

  destinations.
Short press without the
engine
 
running:
 
on
 
/
 
off.
Short press with the engine
running:
 
audio
 
source
 
off
 
/
 

restore.
MO

d
E
 
button:
 
Selection
 of
 
the
 
type
 
of
 
permanent
 
display

.
Long
 
press:
 
black
 
screen
 
(DARK). Selection

 
and
 
confirmation
 
OK
  knob:
Selection
 
of
 
an
 
item
 
on
 
the
 
screen   or   in   a   list   or   a   menu,  
then

 
confirmation
 
with
 
a
 
short
 
press.
Other
 
than
 
for
 
menus
 
and
 
lists,   a   short   press   displays   a  
contextual

 
menu
 
depending
 
on   the   current   screen.
Rotation
 
with
 
map
 
displayed:
 
zoom   the   map   scale   in  

and

 
out.
Volume
 
adjustment
 
(each
 
source is independent,
including

 
T

A
 

messages
 
and
 
navigation

 
instructions).

01
10.5
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Continuous press: reinitialisation of  the  system.
o

pen the " t
elephone
"   menu  
and display the list of recent
calls

 
or
 
accept   an   incoming   call.
FIrSt StEPS
Short press: select pre-set radio station.
Long   press:   pre-set   the   current   station.
a
ccess to the "M u SI c "   menu,   and   display   of   the   CD/MP3/
a

pple
® tracks and folders.
Long
 
press:   display   the   audio   settings   screen   for   the  
"

ME
d
IA"   (CD/USB/iPod/Streaming/AUX)   sources.a
ccess to the "
r
A
d
IO"
 
menu
 
and
 display
 
the
 
list
 
of
 
stations
 
received.
Long
 
press:
 
display
 
the
 
audio
 
settings
 
screen

 
for
 
the
 
radio
 
tuner
 
source.