2013 YAMAHA RHINO 700 stop start

4-4
TIP●
Due to the synchronizing mechanism in
the differential gear case, the four-wheel-
drive indicator may not come on until the
Rhino starts moving.
●
When the On-Command differential gear
lock switch is set to “LOCK” or “4WD”, the
indicator “ ” and the indicator light
“DIFF. LOCK” will flash until the differen-
tial gear is completely locked or un-
locked. If the indicator and the indicator
light continue to flash, the differential is
not completely locked or unlocked. In this
case, start moving to allow time for the
differential to lock or unlock.
5B410002Coolant temperature warning light “ ”
If the coolant temperature reaches a specific
level, this light comes on to warn that the cool-
ant temperature is too hot. If the light comes
on during operation, stop the engine as soon
as it is safe to do so and allow the engine to
cool down for about 10 minutes.
(See page 8-62.)
The electrical circuit of the warning light can
be checked by turning the key to “ON”. If the
warning light does not come on initially when
the key is turned to “ON”, or if the warning light
remains on, have a Yamaha dealer check the
electrical circuit.
DIFF.
LOCK
1RB7A_EE.book Page 4 Tuesday, April 24, 2012 9:07 AM

4-15
EVU00260Accelerator pedal
Press the accelerator pedal down to increase
engine speed. Spring tension returns the ped-
al to the rest position when released. Always
check that the accelerator pedal returns nor-
mally before starting the engine.1. Accelerator pedal
EVU00270Brake pedal
Press the brake pedal to slow or stop the ve-
hicle.1. Brake pedal
1RB7A_EE.book Page 15 Tuesday, April 24, 2012 9:07 AM

6-5
Shifting: neutral to reverse
WARNING
Before you shift into reverse, make sure
there are no obstacles or people behind
you. When it is safe to proceed, go slowly.
Hitting an obstacle or person could result
in serious injury or death.1. Stop the vehicle, take your foot off the ac-celerator pedal, and check behind you.
2. Apply the brake pedal.
3. Shift from neutral to reverse or vice versa
by moving the drive select lever along the
shift guide.
●
When in reverse, the reverse indicator
light should be on. Due to the synchro-
nizing mechanism in the engine, the
light may not come on until the vehicle
starts moving.
●
If the light does not come on, ask a
Yamaha dealer to inspect the reverse
indicator light electrical circuit.
1. Drive select lever 2. L (Low-range)
3. H (High-range) 4. N (Neutral)
5. R (Reverse)4. Release the parking brake.
5. Check behind the vehicle for people or obstacles, and then release the brake
pedal.
6. Press the accelerator pedal gradually
and continue to watch to the rear while
backing.
2
5 4
3
1RB7A_EE.book Page 5 Tuesday, April 24, 2012 9:07 AM

7-21
Uphill
Do not attempt to climb hills until you have
mastered basic maneuvers on flat ground.
Drive straight up hills, and avoid crossing the
side of a hill, which increases your risk of roll-
over. Practice first on gentle slopes before at-
tempting steeper hills. Always check the
terrain carefully before attempting any hill.
To climb a hill, you need traction, momentum,
and steady throttle. For more traction and
control for climbing steeper and/or rougher
slopes, shift into low gear and select “4WD” or
“LOCK”. Travel fast enough to maintain mo-
mentum, but not so fast that you cannot react
to changes in the terrain as you climb.Slow down when you reach the crest of the hill
if you cannot see clearly what is on the other
side – there could be another person, an ob-
stacle, or a sharp drop-off.
If you start to lose traction or momentum
when climbing, and decide you will be unable
to continue, use the brakes to stop. Do not at-
tempt to turn the vehicle around. With your
foot on the brake pedal, look behind you and
plan your descent. Shift the drive select lever
into reverse so you can use engine braking to
slow your descent. Release the brake and be-
gin to coast down the hill. Use engine braking
as much as possible, gently applying the
brakes when necessary.1RB7A_EE.book Page 21 Tuesday, April 24, 2012 9:07 AM

8-33
EVU00780V-belt case drain plug
The V-belt case drain plug is located under
the driver seat. (See page 4-18 for seat re-
moval and installation procedures.)
After riding in water deep enough to allow wa-
ter to enter the V-belt case, remove the drain
plug to drain any water from the case.
If water drains from the V-belt case after re-
moving the drain plug, have a Yamaha dealer
inspect the vehicle, as the water may affect
other engine parts.1. V-belt case drain plug
5B410018Cleaning the spark arrester
WARNING
Hot exhaust system may cause burns. To
avoid burns or fires, make sure that the en-
gine is stopped and the exhaust system is
cool before cleaning the spark arrester. Do
not start the engine while cleaning the ex-
haust system.1. Remove the tailpipe bolts.1. Tailpipe bolt (× 3)
1
1
1RB7A_EE.book Page 33 Tuesday, April 24, 2012 9:07 AM