2013 YAMAHA RHINO 700 differential

8-18
9. Install the final gear case guard by install-ing the bolts and the collars, and then
tightening the bolts to the specified
torque.
5B410014Differential gear oil
Checking the differential gear oil level1. Park the vehicle on a level surface.
2. Remove the differential gear oil filler bolt and its gasket, and then check the oil lev-
el. It should be up to the brim of the filler
hole.
3. If the level is low, add sufficient oil of the
recommended type to raise it to the spec-
ified level. NOTICE: Be sure no foreign
material enters the differential gear
case.
Tightening torque:
Final gear case guard bolt: 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
1RB7A_EE.book Page 18 Tuesday, April 24, 2012 9:07 AM

8-19
1. Differential gear oil filler bolt
2. Gasket 3. Differential gear oil
4. Correct oil level
4. Check the gasket for damage, and re-
place it if necessary.
5. Install the differential gear oil filler bolt
and its gasket, and then tighten the bolt
to the specified torque.
1
2
3
4
Tightening torque:Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
1RB7A_EE.book Page 19 Tuesday, April 24, 2012 9:07 AM

8-20
Changing the differential gear oil1. Park the vehicle on a level surface.
2. Remove the differential gear case guard by removing the bolts and the collars.1. Differential gear case guard
2. Bolt and collar ( × 7)
3. Place an oil pan under the differential
gear case to collect the used oil.
4. Remove the differential gear oil filler bolt,
the differential gear oil drain bolt and their
gasket to drain the oil.1. Differential gear oil drain bolt
2. Gasket5. Install the differential gear oil drain boltand its new gasket, and tighten the bolt to
the specified torque.
1
2
2 2
12
1RB7A_EE.book Page 20 Tuesday, April 24, 2012 9:07 AM

8-21
6. Refill the differential gear case with therecommended oil. NOTICE: Be sure no
foreign material enters the differential
gear case.
7. Check the oil filler bolt gasket for dam- age, and replace it if necessary.
8. Install the differential gear oil filler bolt
and its gasket, and then tighten the bolt
to the specified torque. 9. Check for oil leakage. If oil leakage is
found, check for the cause.
10. Install the differential gear case guard by
installing the bolts and the collars, and
then tightening the bolts to the specified
torque.
Tightening torque:
Differential gear oil drain bolt: 9.8 Nm (0.98 m·kgf, 7.1 ft·lbf)
Recommended oil: SAE 80 API GL-4 Hypoid gear oil
Oil quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)
Tightening torque: Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
Tightening torque:Differential gear case guard bolt: 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
1RB7A_EE.book Page 21 Tuesday, April 24, 2012 9:07 AM

10-2
1
2
3
4
5
6
7
8
910
11
12
13
14
Type:SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MAEngine oil quantity:Without oil filter cartridge replacement:
2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter cartridge replacement: 2.10 L (2.22 US qt, 1.85 Imp.qt)Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.25 L (0.26 US qt, 0.22 Imp.qt)Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil Quantity:
0.18 L (0.19 US qt, 0.16 Imp.qt)
Cooling system:Coolant reservoir capacity (up to the maximum level mark):
0.32 L (0.34 US qt, 0.28 Imp.qt)
Radiator capacity (including all routes): 2.35 L (2.48 US qt, 2.07 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:YXR7FD Regular unleaded gasoline only
YXR7FSPD Regular unleaded gasoline only
YXR700FAD Unleaded gasoline only
Fuel tank capacity: 30.0 L (7.93 US gal, 6.60 Imp.gal)Fuel injection:Throttle body:
ID mark:5B41 00Spark plug (s):Manufacturer/model:NGK/CPR7EA-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:Wet, centrifugal automaticTransmission:Primary reduction system:
V-belt
0 10 30 50 70 90 110 130 ˚F
–20 –10 0 10 20 30 40 50 ˚CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
1RB7A_EE.book Page 2 Tuesday, April 24, 2012 9:07 AM

10-5
Coolant temperature warning light:
LED
Engine trouble warning light: LED
Parking brake indicator light:
LED
On-Command four-wheel-drive/differential gear lock indica-
tor:
LCD
High-range indicator light: LED
Low-range indicator light: LED
Differential gear lock indicator light:
LED
Helmet/Seat belt indicator light: 14 V, 1.7 W
Fuses:Main fuse:
40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Signaling system fuse:
10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Backup fuse:
10.0 A Four-wheel-drive motor fuse:
10.0 A
Radiator fan fuse: 25.0 A
For Europe only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
1RB7A_EE.book Page 5 Tuesday, April 24, 2012 9:07 AM