2013 YAMAHA RHINO 700 display

4-6
Helmet/seat belt indicator light “ / ”1. Helmet/seat belt indicator light “ / ”The indicator light comes on when the key is
turned to “ON” to remind the occupants to al-
ways wear a helmet and to fasten their seat
belt. The indicator light stays on even when
the seat belt is properly latched.
If the indicator light does not come on when
the key is turned to “ON”, have a Yamaha
dealer check the electrical circuit.
5B410004*Multi-function meter unit1. Speedometer 2. Fuel meter
3. “H” button 4. “M” button
5. Clock/Hour meter/Voltage display
6. Odometer/Tripmeter A/Tripmeter B
7. “TRIP/ODO” button 8. Clock/Hour button “ / ”The multi-function meter unit is equipped with
the following:●
a speedometer
●
an odometer
123
4
5
6
7 8
1RB7A_EE.book Page 6 Tuesday, April 24, 2012 9:07 AM

4-7
●
two tripmeters (which show the distance
traveled since they were last set to zero)
●
a clock
●
an hour meter (which shows the total time
the engine has been running)
●
a voltage display (which shows the battery
voltage)
●
a fuel meter
●
a self-diagnosis device
Odometer and tripmeter modes
1. Odometer/Tripmeter A/Tripmeter B
2. “TRIP/ODO” buttonPushing the “TRIP/ODO” button switches the
display between the odometer mode “ODO”
and the tripmeter modes “TRIP A” and
“TRIP B” in the following order:
ODO
→ TRIP A → TRIP B → ODO
1
2
1RB7A_EE.book Page 7 Tuesday, April 24, 2012 9:07 AM

4-8
To reset a tripmeter, select it by pushing the
“TRIP/ODO” button, and then hold the “TRIP/
ODO” button for at least three seconds. The
tripmeters can be used to estimate the dis-
tance that can be traveled with a full tank of fu-
el. This information enables you to plan future
fuel stops.TIPTo switch the display between “km/h” and
“mph”, turn the key to “OFF”, then push and
hold the “TRIP/ODO” button while turning the
key to “ON”.
Clock, hour meter and voltage display
modes1. Clock/Hour button “ / ”
2. “H” button 3. “M” button
4. Clock/Hour meter/Voltage displayPushing the “ / ” button switches the dis-
play between the clock mode “CLOCK”, the
hour meter mode “HOUR”, and the voltage
display mode “ ” in the following order:
CLOCK → HOUR → → CLOCK
4
1
2
3
1RB7A_EE.book Page 8 Tuesday, April 24, 2012 9:07 AM

4-9
To set the clock1. Set the display to the clock.
2. Push the “ / ” button until the clockstarts flashing.
3. Set the hours by pushing the “H” button.
4. Set the minutes by pushing the “M” but- ton.
5. Push the “ / ” button, and then re- lease it to start the clock. Voltage display mode
This display shows the battery voltage.
“ ” appears for 1 second when the volt-
age display mode is first selected, and then
“ ” appears and the battery voltage is dis-
played.
If the battery voltage is less than 10 volts, “LO”
is displayed, and if the voltage is above 16
volts, “HI” is displayed.
1RB7A_EE.book Page 9 Tuesday, April 24, 2012 9:07 AM

4-10
NOTICEIf the voltage display indicates “LO” or
“HI”, there may be trouble with the battery
charging circuit or the battery may be
faulty. If this occurs, have a Yamaha dealer
check or repair the vehicle.
Fuel meter1. Fuel level warning indicator
2. Fuel meter 3. “E” segmentThe fuel meter indicates the amount of fuel in
the fuel tank. The display segments of the fuel
meter disappear from “F” (full) towards “E”
(empty) as the fuel level decreases. When the
“E” segment disappears and the fuel level
warning indicator flashes, refuel as soon as
possible.
123
1RB7A_EE.book Page 10 Tuesday, April 24, 2012 9:07 AM

4-11
TIPThis fuel meter is equipped with a self-diagno-
sis system. If a problem is detected in an elec-
trical circuit, all the display segments and fuel
level warning indicator start flashing. If this oc-
curs, have a Yamaha dealer check the electri-
cal circuit.
Self-diagnosis device1. Engine trouble warning light “ ”
2. Error code displayThis model is equipped with a self-diagnosis
device for various electrical circuits.
If a problem is detected in any of those cir-
cuits, the engine trouble warning light comes
on or flashes, and the multi-function display
indicates an error code.
If the multi-function display indicates an error
code, note the code number, and then have a
Yamaha dealer check the vehicle.
2
1
1RB7A_EE.book Page 11 Tuesday, April 24, 2012 9:07 AM

4-12
NOTICEIf the multi-function display indicates an
error code, the vehicle should be checked
as soon as possible in order to avoid en-
gine damage.
EVU00240Light switch “OFF/ / ”1. Light switch “OFF/ / ”Set the switch to “ ” to turn on the low beam
and the taillights.
Set the switch to “ ” to turn on the high
beam and the taillights.
Set the switch to “OFF” to turn off the head-
lights and taillights.
L
H
L
HL
H
1RB7A_EE.book Page 12 Tuesday, April 24, 2012 9:07 AM

6-6
5B410009On-Command four-wheel-drive switch and
differential gear lock switch
You may notice that the vehicle handles dif-
ferently in “2WD”, “4WD”, and “LOCK”. For
example, you should expect that the vehicle
will require more effort to turn in “LOCK”. Al-
ways stop the vehicle before changing be-
tween “2WD” and “4WD” or “4WD” and
“LOCK”.“2WD”/“4WD”
To change from “2WD” to “4WD”, stop the ve-
hicle, and then set the switch to “4WD”. When
the vehicle is in four-wheel drive, the four-
wheel-drive indicator “ ” will come on in the
multi-function display. To change from “4WD”
to “2WD”, stop the vehicle, and then set the
switch to “2WD”.
1. On-Command four-wheel-drive switch “2WD”/“4WD”
1RB7A_EE.book Page 6 Tuesday, April 24, 2012 9:07 AM