2013 YAMAHA GRIZZLY 125 headlight bulb

Parking on a slope ..................................... 6-5
Accessories and loading ............................ 6-6
RIDING YOUR ATV ...................................... 7-1 GETTING TO KNOW YOUR ATV............... 7-2
RIDE WITH CARE AND GOOD JUDGMENT .............................................. 7-2
BE CAREFUL WHERE YOU RIDE ............. 7-9
TURNING YOUR ATV .............................. 7-12
CLIMBING UPHILL ................................... 7-14
RIDING DOWNHILL.................................. 7-16
CROSSING A SLOPE............................... 7-17
CROSSING THROUGH SHALLOW WATER ................................................... 7-18
RIDING OVER ROUGH TERRAIN ........... 7-20
SLIDING AND SKIDDING ......................... 7-20
WHAT TO DO IF... .................................... 7-22
WHAT TO DO... ........................................ 7-22
PERIODIC MAINTENANCE AND
ADJUSTMENT ............................................... 8-1 Owner’s manual and tool kit ....................... 8-2
Periodic maintenance chart for the emission control system ................ 8-3
General maintenance and lubrication chart ......................................................... 8-5
Checking the spark plug ............................. 8-9 Engine oil ..................................................8-11
Transmission oil ........................................8-14
Cleaning the engine and V-belt case air
filter elements .........................................8-17
Cleaning the spark arrester ......................8-23
V-belt case drain screw ............................8-24
Adjusting the carburetor ............................8-25
Adjusting the engine idling speed .............8-26
Adjusting the throttle lever free play .........8-26
Valve clearance ........................................8-27
Brakes .......................................................8-28
Checking the front and rear brake shoes ......................................................8-28
Adjusting the front brake lever free play ...8-29
Adjusting the rear brake lever free play ....8-33
Drive chain slack .......................................8-34
Lubricating the drive chain ........................8-37
Checking and lubricating the cables .........8-37
Checking and lubricating the front and rear brake levers .....................................8-38
Checking the wheel hub bearings .............8-39
Lubricating the lower arm pivots ...............8-39
Lubricating the front knuckle pivots ..........8-40
Lubricating the steering shaft ....................8-41
Battery ......................................................8-41
Replacing the fuse ....................................8-44
Replacing a headlight bulb .......................8-45
U1PY61E0.book Page 2 Wednesday, March 14, 2012 5:22 PM

Adjusting a headlight beam ...................... 8-47
Replacing the tail/brake light bulb ............ 8-47
Removing a wheel .................................... 8-48
Installing a wheel ...................................... 8-48
Troubleshooting ....................................... 8-49
Troubleshooting chart .............................. 8-51
CLEANING AND STORAGE .......................... 9-1 Cleaning ..................................................... 9-1
Storage ....................................................... 9-2
SPECIFICATIONS ...................................... 10-1
CONSUMER INFORMATION ...................... 11-1 Identification numbers .............................. 11-1
U1PY61E0.book Page 3 Wednesday, March 14, 2012 5:22 PM

8-45
8
NOTICEECB00640To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.2. Remove the blown fuse, and then install anew fuse of the specified amperage.
WARNING! Always use a fuse of the spec-
ified rating, and never use a substitute ob-
ject in place of the proper fuse. An
improper fuse or a substitute object can
cause damage to the electrical system,
which could lead to a fire.
[EWB02172]
3. Turn the key to “ON” and turn on the electricalcircuits to check if the devices operate.
4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system.EBU25481Replacing a headlight bulb If a headlight bulb burns out, replace it as follows. 1. Remove the cover at the rear of the headlight
by pulling it off.
2. Remove the headlight bulb holder cover by pulling it off.
Specified fuse:
15.0 A
1. Cover at the rear of the headlight
1
U1PY61E0.book Page 45 Wednesday, March 14, 2012 5:22 PM

8-46
8
3. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
4. Remove the burnt-out bulb by pulling it out.
5. Insert a new headlight bulb into the bulb hold- er by pushing it in. NOTICE: Do not touch
the glass part of the headlight bulb to keep
it free from oil, otherwise the transparency
of the glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
[ECB00651]
6. Install the bulb holder by pushing it in and turn- ing it clockwise.
7. Install the bulb holder cover and the cover at the rear of the headlight. NOTICE: Make sure
the headlight bulb holder cover is securely
fitted over the bulb holder and seated
properly.
[ECB00671]
8. Adjust the headlight beam if necessary.
1. Headlight bulb holder cover
2. Headlight bulb holder
1 2
1. Headlight bulb
1
U1PY61E0.book Page 46 Wednesday, March 14, 2012 5:22 PM

8-47
8
EBU25551Adjusting a headlight beam NOTICEECB00690It is advisable to have a Yamaha dealer make
this adjustment.To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
EBU25613Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.1. Remove the tail/brake light bulb holder (to- gether with the bulb) by turning it counter-
clockwise.
2. Remove the burnt-out bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the bulb holder, push it in, and then turn it clockwise until it stops.
1. Headlight beam adjusting screw
1 (a)
(b)
1. Tail/brake light bulb holder
1
U1PY61E0.book Page 47 Wednesday, March 14, 2012 5:22 PM

10-4
10
Spring/shock absorber type:Coil spring/oil damper
Wheel travel: 70 mm (2.8 in)Rear suspension:Type:Swingarm
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
80 mm (3.1 in)Electrical system:Ignition system:DC CDI
Charging system:
AC magnetoBattery:Model:12N12C-4A-2
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 1
Neutral indicator light:
12 V, 1.7 W × 1 Reverse indicator light:
12 V, 1.7 W × 1
Fuses:Main fuse:
15.0 AEBU30401For Europe only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
U1PY61E0.book Page 4 Wednesday, March 14, 2012 5:22 PM

INDEX
AAccessories and loading ................................................ 6-6
Air filter elements, engine and V-belt filter cleaning ..... 8-17BBattery ................................................................... 5-6, 8-41
Brake lever free play, adjusting the front ...................... 8-29
Brake lever free play (rear), adjusting .......................... 8-33
Brake lever, front ............................................................ 4-4
Brake lever, rear ............................................................. 4-5
Brake levers, checking and lubricating ......................... 8-38
Brakes .......................................................................... 8-28
Brakes, front and rear .................................................... 5-3
Brake shoes, checking the front and rear .................... 8-28CCables, checking and lubricating ................................. 8-37
Carburetor, adjusting .................................................... 8-25
Carrier, front ................................................................. 4-11
Carrier, rear .................................................................. 4-11
Chassis fasteners ........................................................... 5-6
Cleaning ......................................................................... 9-1DDrive chain ..................................................................... 5-3
Drive chain, lubricating ................................................. 8-37
Drive chain slack .......................................................... 8-34
Drive select lever ............................................................ 4-6
Drive select lever and driving in reverse ........................ 6-3EEngine break-in .............................................................. 6-4 Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-26
Engine oil .............................................................. 5-3, 8-11
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-2
FFront knuckle pivots, lubricating ................................... 8-40
Fuel ......................................................................... 4-7, 5-3
Fuel cock ........................................................................ 4-8
Fuel tank cap .................................................................. 4-7
Fuse, replacing ............................................................. 8-44HHandlebar switches ........................................................ 4-2
Headlight beam, adjusting ............................................ 8-47
Headlight bulb, replacing .............................................. 8-45
Horn switch .................................................................... 4-3IIdentification numbers .................................................. 11-1
Indicator lights ................................................................ 4-2
Instruments, lights and switches .................................... 5-6LLabel locations ............................................................... 1-1
Light switch .................................................................... 4-3MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-1
U1PY61E0.book Page 1 Wednesday, March 14, 2012 5:22 PM