2013 VOLKSWAGEN TOUAREG headlight

If the light switch is in the AUT O position, the outside vehicle lighting and the instrument lighting are
automatically switched on at dusk/nightfall and off in normal daylight in the following situations ⇒ :

Automatic activation: Automatic deactivation/change to daytime
running lights:
If the low-light sensor registers darkness, for
example when driving through a tunnel.
If sufficient brightness is registered.
If you drive faster than about 87 mph (140 km/h)
for several seconds.
If you drive slower than about 40 mph (65 km/h)
for several seconds.
If the rain sensor recognizes heavy rain and
switches the windshield wipers on.
If the windshield wipers have not moved for
several minutes.

Adaptive Front Lighting System (AFS)
The Adaptive Front Lighting System works only with the low beams switched on and only at speeds
above about 6 mph (10 km/h). The swivel-mounted lamps automatically improve road illumination
during cornering.
The Adaptive Front Lighting System can be switched on and off in the Infotainment System.
x Switch on the ignition.
x Press the CARInfotainment button.
x Tap the Assist systems function key on the screen.
x Select the menu item Light assistance (main beam control)from the list.
x Tap Adaptive front lighting system (AFS) to enable or disable this feature.
On some models, the headlights move independently of each other, even in straight-ahead driving.
They adapt to weather conditions and speed to better illuminate the roadway. The headlights return to
their original position after a delay, depending on the speed of the vehicle.
.WARNING
Crashes and other accidents can happen when you cannot see the road ahead and when you
cannot be seen by other motorists.
x Never use daytime running lights (DRL) to see where you are going. DRL are not bright
enough to light up the roadway and be seen by other motorists. You will not be able to see far
enough ahead for safety, especially at dusk or when it is dark. Always switch on the low
beam headlights at dusk or when it is dark.
x If automatic headlight control (AUTO) is switched on, the low beam headlights still may not
be switched on in fog or heavy rain. You have to switch on the low beam headlights yourself.
x The taillights do not come on when the daytime running lights are switched on. A vehicle
without taillights on cannot be seen by others in bad weather, at dusk, or when it is dark.
In cool or humid weather, the insides of the headlights, rear lights, and turn signals can
temporarily fog up. This is normal and does not affect the service life of the vehicle's lighting system.
“Coming home” and “Leaving home” feature (orientation lighting)

Enabling and disabling the “Coming home” and “Leaving home” functions
The “Coming home” and “Leaving home” functions can be enabled or disabled in the Infotainment
System.
x Switch on the ignition.
x Press the CARInfotainment button.
x Tap the Settingsfunction key on the screen.
x Select the menu item External lightingin the list.
x Tap Leaving homeor Coming hometo enable or disable the feature.
The feature is enabled when the check box in the Leaving homeor Coming homefunction key is checked =.
Switching the “Coming home” and “Leaving home” functions on and off
The “Coming home” feature must be switched on manually. The “Leaving home” feature is
automatically controlled by a low-light sensor.

“Coming home” Action
Switch on: – Switch off the ignition.
– Operate the headlight flasher for about 1 second.
Opening the driver door switches on the “Coming home” feature. The delay
period starts when the last vehicle door or the rear hatch is closed. The
“Coming home” lighting is switched on when the driver door is open, the
headlight switch is set to AUTO, and the low light sensor detects darkness.
The delay period starts once the last vehicle door or the rear hatch is closed.
Switch off: – Automatically after the preset delay period is over.
– Automatically if any door or the rear hatch is still open about 60 seconds
after activation.
– Turn the light switch to the  position.
– Switch on the ignition.


“Leaving home” Action
Switch on: – Unlock the vehicle when the light switch is not in the O position and the low-
light sensor registers darkness. Unlock the vehicle if the light switch is in the
AUTO position and the low-light sensor registers darkness.
Switch off: – Automatically after the preset delay period is over.
– Lock the vehicle.
– Turn the light switch to the / position.
– Switch on the ignition.

Background lighting in the outside mirrors
The background lighting in the outside mirrors lights up the area close to the doors while you are
getting into or out of the vehicle. It is switched on when the vehicle is unlocked, a vehicle door is
opened, or the “Coming home” or “Leaving home” feature is activated. If the vehicle is equipped with a
light sensor, the background lighting in the outside mirrors is only switched on in darkness.

The lights stay on for about 10 seconds (lighting delay period). The “Coming home” and
“Leaving home” functions can be enabled and disabled in the Infotainment System.
If the “Coming home” feature is switched on and the driver door is opened, no acoustic warning
will sound to alert that the light is still on.
Instrument panel lighting , headlight range adjustment

Fig. 85 Next to the steering wheel: Control for instrument cluster lighting.

Function key: Effect
Day/night : define map display settings.
Day: map view remains in bright daytime design.
Night: map display remains in dark night time design.
Automatic: daytime or night time design of the map view changes as the low beam headlights are
switched on and off.

Explanation of fig. 259:
(1) Center cover.
(2) Right cover.
(3) Left cover.
(4) Retainers.
(5) Opening for jump starting.
(6) Warning label for high-voltage hybrid components.
(7) Engine compartment seal.
Engine compartment covers (1) and (3) must be removed in the following situations:
x Changing light bulbs in the left headlight assembly.
Engine compartment covers (1) and (2) must be removed in the following situations:
x Changing light bulbs in the right headlight assembly.
x Adding engine coolant to the low temperature coolant circuit .
Removing engine compartment cover
When removing any part of the engine compartment cover, always pull CARefully on the relevant
attachment points ⇒ .
x Open the engine hood

x Shape of the bank.
x Objects in the water.
x Maximum fording depth of the vehicle.
Before driving through water
Stop, get out of the vehicle, and assess the situation ⇒ :
x Measure water depth from one side to the other. Check the firmness of the bed and banks; check
for drop-offs and obstacles in the water ⇒ .
x Make sure it is possible to enter and exit the water safely.
x Check the angle of the embankment and the firmness of the ground on each bank.
x Switch to off-road mode.
Driving through standing and slow-moving water
The vehicle can drive through standing water if the ground under the water is firm enough ⇒ .
Never exceed maximum fording depth.
x Drive slowly into a river in the direction of the flow. Never exceed the departure/approach angle
and lateral angle (vehicle slope).
x Always drive at a constant speed to the other side.
This will help prevent engine damage from the water. It also allows an air pocket to form in front of the
engine that can supply it with the necessary air.
Entering the water quickly or driving too fast through the water will create a bow wave. A bow wave
can force its way into the engine air intake duct and seriously damage the engine.
Driving through fast-moving water
Driving through fast-moving water is very dangerous ⇒ .
The vehicle can be swept away by the current. Even vehicles with high ground clearance can get
stuck if the ground is washed out from under the tires. Fast-moving water will build up against the side
of your vehicle. This will make the water deeper. Always think about this before entering the water.
Water volume, speed, and depth can be very unpredictable and dangerous.
If you are uncertain how fast the water is flowing, look for a shallower place where you can cross in
safety. If you cannot find a safe place to cross, turn back.
Headlight washer system instructions
Do not use the headlight washer system when driving through water. Things in the water can enter
into the openings when the washer nozzles are extended. This can prevent the washer nozzles from
retracting to their normal position. If this should happen, CARefully remove the objects.
After driving through water
x After crossing through deep water, stop the engine and check the oil dipstick. If there are beads of
water on the oil dipstick or the oil level has increased, do not start the engine. Change the engine oil
immediately. Depending on the amount of water in the oil, running or starting the engine can result in
engine failure or serious engine damage.
x Always dry the brakes by braking a couple of times.

.WARNING
High voltage systems in the engine compartment can cause electrical shocks or even
electrocution, severe burns, other serious injuries, and even death!
x Never short-circuit the electrical system. Be especially CAReful when using jumper
cables. The vehicle's battery could explode!
x To reduce the risk of electrical shock and personal injury while the engine is running or
being started:
– Never touch ignition cables. Never touch other components of the high-voltage
electronic ignition system.
– Never touch the wiring of the HID - High Intensity Discharge (Xenon) headlights.
.WARNING
Moving parts in the engine compartment can cause serious personal injury on contact.
x Never reach into the area around or touch the radiator fan. Contact with the blades can
cause serious personal injury. Always remember that the radiator fan is temperature-
controlled and can come on suddenly even when the engine has been switched off for a while
and the key has been removed from the ignition.
x If you have to perform a check or repair when the engine is running, there are more risks
from the rotating parts, such as the drive belts, alternator, radiator fan, etc., and from the
high-voltage ignition system. Always use extreme CARe.
– Always make sure that jewelry, loose clothing and long hair do not get caught in
rotating engine parts. Before starting any work remove your jewelry, take off your necktie,
tie back and cover your hair, and do not wear clothing that can hang down and get caught
in moving engine parts.
– Always use extreme caution if the accelerator pedal has to be depressed to perform a
check. The vehicle will start to move even if the parking brake is on.
x Never leave any objects in the engine compartment, for example cleaning rags and tools.
Objects left behind can cause malfunctions, engine damage, and even fires.
.WARNING
Operating fluids and some materials in the engine compartment can catch fire easily, causing
burns and other serious personal injuries!
x Do not smoke.
x Never work next to open flames or sparks.
x Never pour or spill operating fluids or other flammable liquids on the engine. These fluids
can ignite on hot engine parts and cause injuries.
x If work on the fuel system or the electrical system is necessary:
– Always disconnect the 12 Volt vehicle battery. Make sure the vehicle is unlocked when
you disconnect the battery, or the alarm will go off. Never touch the electrical wiring of the
ignition system.
– Never work near heaters, water heaters, or other open flames.
x Always have a functional, approved fire extinguisher nearby.