2013 TOYOTA HILUX ECU

527 4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_OM_OM0K134E_(EE)
FuseAmpereCircuit
4OBD7.5 AOn-board diagnosis system
5INJ15 A
Multiport fuel injection system/
sequential multiport fuel injection
system
6ECU-IG &
GAUGE10 A
Air conditioning system, charging
system, rear differential lock sys-
tem, ABS, TRC, VSC, emergency
flashers, turn signal lights, back-up
lights, multiport fuel injection sys-
tem/sequential multiport fuel injec-
tion system, shift lock control
system, rear window defogger,
headlights, door courtesy switches,
power door lock system, wireless
remote control system, steering
sensor, daytime running light sys-
tem, cruise control, headlight clean-
ers, seat heaters, outside rear view
mirror defoggers, multi-information
display and passenger’s seat belt
reminder light
7WIP20 AWindshield wiper and washer
8IGN7.5 A
Multiport fuel injection system/
sequential multiport fuel injection
system, SRS airbags and fuel pump
9ACC7.5 A
Audio system, power outlet, clock,
power rear view mirror control sys-
tem, shift lock control system and
multi-information display

529 4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_OM_OM0K134E_(EE)Driver’s side instrument panel (rear side)
FuseAmpereCircuit
1AM140 A
Rear differential lock system, ABS,
TRC, VSC, ACC, CIG, ECU-IG &
GAUGE, and WIP fuses
2IG140 APWR, S-HTR, 4WD, DOOR, DEF
and MIR HTR fuses

542 4-3. Do-it-yourself maintenance
HILUX_OM_OM0K134E_(EE)Stop/tail lights, rear turn signal lights, back-up lights and rear
fog light
Remove the securing bolts and
remove the unit.
Turn the bulb base counterclock-
wise.
Stop/tail light
Rear turn signal light
Back-up light or rear fog light
Remove the light bulb.
Stop/tail light
Rear turn signal light
Back-up light or rear fog light
STEP1
STEP2
STEP3

544 4-3. Do-it-yourself maintenance
HILUX_OM_OM0K134E_(EE)Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by
any authorized Toyota dealer or repairer, or another duly qualified
and equipped professional.
Side turn signal lights (mirror-mounted type) (if equipped)
High mounted stoplight (if equipped)
When installing the rubber cover of the headlight
Ensure the rubber cover is securely attached.
LED light bulbs
The high mounted stoplight consists of a number of LEDs. If any of the LEDs
burn out, take your vehicle to any authorized Toyota dealer or repairer, or
another duly qualified and equipped professional to have the light replaced.
Condensation build-up on the inside of the lens
Contact any authorized Toyota dealer or repairer, or another duly qualified
and equipped professional for more information in the following situations.
Temporary condensation build-up on the inside of the headlight lens does
not indicate a malfunction.
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
Fit the rubber cover outer circumfer-
ence in firmly.
Fit the rubber cover around the light
bulb in until the light bulb plug can be
seen.

545 4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_OM_OM0K134E_(EE)
CAUTION
Replacing light bulbs
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
To prevent damage or fire
Make sure bulbs are fully seated and locked.
Check the wattage of the bulb before installing to prevent heat damage.

550 5-1. Essential information
HILUX_OM_OM0K134E_(EE)
Emergency towing
If a tow truck is not available in
an emergency, your vehicle may
be temporarily towed using a
cable or chain secured to the
emergency towing eyelet(s).
This should only be attempted
on hard surfaced roads for short
distances at low speeds.
A driver must be in the vehicle to
steer and operate the brakes.
The vehicle’s wheels, drive train,
axles, steering and brakes must
be in good condition.

5
579 5-2. Steps to take in an emergency
When trouble arises
HILUX_OM_OM0K134E_(EE)
Stowing the flat tire, jack and all tools
Lay down the tire with the outer
side facing up, and hook the
holding bracket as shown in the
illustration.
Raise the tire.
After the tire goes half way up,
check that the suspended chain is
able to enter the tire hole, for
proper storage.
Check the tire from the side to
see that the tire is stored horizon-
tally.
Stow the tools and jack securely.
STEP1
STEP2
STEP3

5
581 5-2. Steps to take in an emergency
When trouble arises
HILUX_OM_OM0K134E_(EE)
CAUTION
Using the tire jack
Improper use of the tire jack may cause the vehicle to suddenly fall off the
jack, leading to death or serious injury.
Do not use the tire jack for any purpose other than replacing tires or install-
ing and removing tire chains.
Only use the tire jack that comes with this vehicle for replacing a flat tire.
Do not use it on other vehicles, and do not use other tire jacks for replac-
ing tires on this vehicle.
Always check that the tire jack is securely set to the correct jack up point.
Do not put any part of your body under the vehicle while it is supported by
the jack.
Do not start or run the engine while your vehicle is supported by the jack.
Do not raise the vehicle while someone is inside.
When raising the vehicle, do not put an object on or under the jack.
Do not raise the vehicle to a height greater than that required to replace
the tire.
Use a jack stand if it is necessary to get under the vehicle.
Take particular care when lowering the vehicle to ensure that no one working
on or near the vehicle may be injured.
Do not continue jacking up once the
yellow caution line has appeared.
Ye l l o w
caution line