2013 SUZUKI ALTO ignition

5-9
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Accessory Socket
(if equipped)
ALTO 800
53M-07-032
ALTO K10
Manual Transaxle
53M-07-033
Automated Manual Transaxle
53M-07-034
The accessory socket will work when the
ignition switch is in the “ACC” or “ON” posi-
tion. This socket can be used to provide
12volt/120 watt power for electrical acces-
sories. Check that the cap remains on the
socket when socket is not in use.
Assist Grips (if equipped)
53MH0518
Assist grips are provided for convenience.
EXAMPLE
EXAMPLENOTICE
Use of inappropriate electrical acces-
sories can cause damage to your
vehicle’s electrical system. Make
sure that any electrical accessories
you use are designed to plug into this
type of socket.
EXAMPLE
NOTICE
To avoid damaging the assist grip
and the molded headlining, do not
hang down the assist grip.
EXAMPLE

6-3
VEHICLE LOADING AND TOWING
53MH0-74E
B: 2WD VEHICLES WITH MANUAL
TRANSAXLE OR AUTO GEAR SHIFT
1) Shift the gearshift lever into neutral.
2) Turn the ignition key to the “ACC” posi-
tion to unlock the steering wheel.
3) Release the parking brake.
NOTICE
After shifting the auto gear shift gear-
shift lever to the “N” position, always
check the gear position indicator in
the instrument cluster shows the “N”
position to make sure that the
transaxle is disengaged.
If the transaxle cannot be put in neutral,
turn the key from the “OFF” to the
“ON” position, and move the auto gear
shift lever from “N” to “D”, “M” or “R”,
then back to “N” again. Then turn the
key from the “ON” to the “OFF” posi-
tion.
These procedures may help put the
transaxle in neutral. If the transaxle
still cannot be put in neutral, you can-
not tow the vehicle without using a
towing dolly.
NOTICE
The steering column is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing. Always unlock the steering
wheel before towing.

7-1
INSPECTION AND MAINTENANCE
53MH0-74E
60A187S
WA R N I N G
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be espe-
cially careful to observe:
(Continued)
WA R N I N G
(Continued)
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, be
sure the battery is disconnected
and the ignition switch has been in
the “LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components, seat belt preten-
sioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
(Continued)
WA R N I N G
(Continued)
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is set
fully and the transaxle is in Neutral.
• Do not touch ignition wires or other
ignition system parts when start-
ing the engine or when the engine
is running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.

7-3
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) AIIIIIIRAI
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3.Engine oil and Oil filter R I RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage) I I IIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine mounting (Loose, Damage) – – T – T – T – T –
7. Valve Clearance – A – A – A – A – A
8. Camshaft timing belt (Damage, Wear)–––I–I–I–I
Replace Every 1,00,000 km
9. Exhaust system (Noise, Leakage etc.) – I – I – I – I – I
10. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2. Spark plugs (Clean and Adjust the gap) – – I R I R I R I R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) I I I I I R I I I R
CLUTCH AND TRANMISSION
1. Clutch pedal (Play) I I IIIIIIII
2. Clutch slipping (Dragging or Excessive damage) I I IIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years, which ever comes earlier
DRIVE SHAFTS
1. Drive shafts boot (Boot cut / Damage) – I IIIIIIII
2.Drive Shaft Noise IIIIIIIIII

7-7
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) ––––– I ––– I
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3. Engine oil and Oil filter – – RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage)IIIIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine Mounting (Loose, Damage) – – T – T – T – T –
7.Valve Clearance –––– I –– I ––
8. Exhaust System (Noise, Leakage etc.) – I – I – I – I – I
9. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2.Spark plugs –––––R–––R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) – I I I I R I I I R
CLUTCH AND TRANMISSION
1.Clutch pedal (Play) IIIIIIIIII
2.Clutch slipping (Dragging or Excessive damage) IIIIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years whichever comes first
DRIVE SHAFTS
1. Drive shaft boots (Boot cut / Damage)IIIIIIIIII
2.Drive Shaft Noise IIIIIIIIII
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2. Brake pedal (Pedal-to-wall clearance)IIIIIIIIII

7-15
INSPECTION AND MAINTENANCE
53MH0-74E
Coolant ReplacementSince special procedures are required, we
recommend you take your vehicle to your
MARUTI SUZUKI dealer for coolant
replacement.
Air Cleaner
ALTO 800
53MM07007
NOTE:
Remove hose (1) from air cleaner case
before unclamping.
ALTO K10
53M-09-017
Unclamp/Unscrew the side clamps/screws,
and remove the element from the air
cleaner case. If it appears to be dirty,
replace it with a new one.
Spark Plugs
You should inspect spark plugs periodically
for carbon deposits. When carbon accu-
mulates on a spark plug, a strong spark
may not be produced. Remove carbon
deposits with a wire or pin and adjust the
spark plug gap.
NOTE:
For ALTO K10: Unclamp the air filter bolt
and then remove the air cleaner case.
ALTO K10
53M-09-019
To access the spark plugs:
1) If necessary, disconnect the coupler (1)
while pushing the release lever.
2) Remove the ignition coil bolts (2).3) Pullout the ignition coil (3) and remove
the spark plug.
NOTE:
When installation, make sure the wires,
couplers, sealing rubber of top cover and
washers, are correctly returned in place.
53MM07008(1)
EXAMPLE
EXAMPLE
EXAMPLE
NOTICE
• When pulling the ignition coils out,
do not pull on the cable. Pulling on
the cable can damage it.
• When servicing the iridium/plati-
num spark plugs (slender center
electrode type plugs), do not touch
the center electrode, as it is easy to
damage.
(1)
(2)(3)
Wrong Right
EXAMPLE

7-24
INSPECTION AND MAINTENANCE
53MH0-74E
53M-09-038
Fuses in the Engine Compartment
ALTO 800
53M-09-039
Fuses in the Engine Compartment
ALTO K10
53M-09-040
MAIN FUSE / PRIMARY FUSE
(1) – Blank
(2) – Blank
(3) – Blank
(4) – Blank
(5) 50A Ignition switch fuse
(6) 50A Battery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9) – Blank
(10) –
Radiator fan relay
(11) – Blank
(12) –
Blank
(13) – Blank
(14) 80A All electric load
(15) – Blank
(16) – Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A A/c compressor fuse
(20) – Fuel pump relay
(21) – Blank
(22) – Blank
(23) 30A Battery 2 fuse
MAIN FUSE / PRIMARY FUSE
(1)
—Blank
(2)
—Blank
(3)
10AFont fog light
(4)
—A/c compressor relay
(5) 50A Ignition switch fuse
(6)
50ABattery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9)
—Blank
(10) — Radiator fan relay
(11) — Blank
(12) — Blank
(13) — Blank

7-26
INSPECTION AND MAINTENANCE
53MH0-74E
ALTO K10
53M-09-044
53M-09-045
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) – Blank
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) – Blank
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) 7.5AAutomated Manual Tran-
saxle 2 (if equipped)
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) 7.5A IG1 SIG
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI dealer.
EXAMPLE