2013 SUZUKI ALTO fuse

0-3
82PH0-74E
WARRANTY POLICY
Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty the vehicle must be delivered by a
Maruti Suzuki authorised dealer and set-up, and serviced by a
Maruti Suzuki authorised dealer / service station.
(2) Term:The term of the warranty shall be twenty-four (24) months or
40,000 kilometers (whichever occurs first) from the date of
invoice to the first owner.
(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle within
the term stipulated above, Maruti Suzuki’s only obligation is to
repair or replace at its sole discretion any part shown to be defec-
tive, with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti Suzuki acknowledges that such a
defect is attributable to faulty material or workmanship at the time
of manufacture. The owner is responsible for any repair or replace-
ments which are not covered by this warranty.
(4) Limitation:
This warranty shall not apply to:
(a) Normal maintenance service required other than the three
free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel bal-
ancing, wheel alignment and tyre rotation, cleaning of injec-
tors, adjustments of clutch and valve clearance.
(b) The replacement of normal wear parts including without lim-
itation, bulbs, tyres and tubes, spark plugs, belts, hoses, fil-
ters, wiper blades, brushes, contact points, fuses, clutch
disc, brake shoes, brake pads, cable and all rubber parts
(except oil seal and glass run).
(c) Any vehicle which has been used for competition or racing.
(d) Any repairs or replacement required as a result of accidents
or collision.
(e) Any defects caused by misuse, negligence, abnormal use or
insufficient care.
(f) Any vehicle which has been modified or altered, including
without limitation, the installation of performance accesso-
ries.
(g) Any vehicle on which parts or accessories not approved by
Maruti Suzuki have been used.
(h) Any vehicle which has not been operated in accordance with
the operating instructions in this Owner’s Manual and Ser-
vice Booklet.
(i) Any vehicle which has not received, during the warranty term,
the service inspections prescribed in this Owner’s Manual
and Service Booklet.
(j) Any vehicle which has been assembled, disassembled,
adjusted or repaired by other than an Maruti Suzuki autho-
rised dealer/service station.
(k) Any vehicle which has been used for purposes other than
what it was designed for.
(l) Any damage or deterioration caused by industrial pollution
and bird droppings.

2-9
BEFORE DRIVING
53MH0-74E TROUBLESHOOTING

SYMPTOMS PROBABLE CAUSES REMEDIES
Transmitter function (Unlock/Lock/Car
Locator) not working 1) Battery of the transmitter is weak.
2) Transmitter is exposed to water or it is
wet.
3) D/L or Dome fuse for controller is blown
in the vehicle.
4) In case if any door is open or door sen-
sor is shorted with the body ground,
remote will not activate the central lock-
ing.1) Check the battery.
2) Dry the transmitter and check it.
3) Check and replace the D/L or Dome
fuse.
4) Check if all doors are properly closed
and door switch functioning is O.K.
Operation distance of the transmitter is
less than 20m but still transmitter (Unlock/
Lock/Car Locator) is not working 1) Battery of the transmitter is weak.
2) Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)1) Check the battery.
2) Drive the vehicle away from the particu-
lar spot and re-test the control distance.
It is difficult to activate or deactivate the
system in certain area using the
transmitter. 1) The strong interference caused by
excessive RF activity in a particular
area1) The interference is temporary and only
while the vehicle is in that area.

INSPECTION AND MAINTENANCE
7
53MH0-74E
INSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................... 7-2
Periodic Maintenance Schedule ........................................ 7-2
Drive Belt ............................................................................. 7-10
Engine Oil and Filter ........................................................... 7-10
Engine Coolant .................................................................... 7-13
Air Cleaner ........................................................................... 7-15
Spark Plugs ......................................................................... 7-15
Gear Oil ................................................................................ 7-16
Clutch Pedal ........................................................................ 7-17
Fuel Filter ............................................................................. 7-17
Brakes .................................................................................. 7-18
Steering ................................................................................ 7-20
Tires ...................................................................................... 7-20
Battery .................................................................................. 7-22
Fuses .................................................................................... 7-23
Bulb Replacement ............................................................... 7-27
Wiper Blades ....................................................................... 7-29
Windshield Washer Fluid ................................................... 7-31
Air Conditioning System .................................................... 7-31

7-23
INSPECTION AND MAINTENANCE
53MH0-74E
53m-09-036
The level of the battery solution must be
kept between the “MAX” and the “MIN”
level lines at all times. If the level is found
to be below the “MIN” level line, add dis-
tilled water to bring level between “MAX”
and “MIN”. You should, however, periodi-
cally check the battery, battery terminals,
and battery holddown bracket for corro-
sion. Remove corrosion using a stiff brush
and ammonia mixed with water, or baking
soda mixed with water. After removing cor-
rosion, rinse with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge.Replacement of the battery53M-09-037
To remove the battery:
1) Disconnect the negative cable (1).
2) Disconnect the positive cable (2).
3) Remove the retainer bolts (3) and
remove the retainer (4).
4) Remove the battery along with cover
assembly (5) (if equipped).To install the battery:
1) Install the battery in the reverse order of
removal.
2) Tighten the retainer nuts and battery
cables securely.
NOTE:
When the battery is disconnected, some of
the vehicle’s function will be initialized and/
or deactivated.
These function are required to reset after
the battery is reconnected.
Fuses
Your vehicle has three types of fuses, as
described below:
Main fuse
The main fuse takes current directly from
the battery.
Primary fuses
These fuses are between the main fuse
and individual fuses, and are for electrical
load groups.
Individual fuses
These fuses are for individual electrical cir-
cuits. To remove a fuse, use the fuse puller
provided in the fuse box.
CAUTION
Do not overfill the battery with dis-
tilled water in order to avoid spillage.
EXAMPLE
NOTICE
• Ensure that battery should not be
removed without cover assembly.
• When the battery is reassembled
into the vehicle, kindly ensure that
battery cover is also installed along
with battery.
EXAMPLE

7-24
INSPECTION AND MAINTENANCE
53MH0-74E
53M-09-038
Fuses in the Engine Compartment
ALTO 800
53M-09-039
Fuses in the Engine Compartment
ALTO K10
53M-09-040
MAIN FUSE / PRIMARY FUSE
(1) – Blank
(2) – Blank
(3) – Blank
(4) – Blank
(5) 50A Ignition switch fuse
(6) 50A Battery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9) – Blank
(10) –
Radiator fan relay
(11) – Blank
(12) –
Blank
(13) – Blank
(14) 80A All electric load
(15) – Blank
(16) – Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A A/c compressor fuse
(20) – Fuel pump relay
(21) – Blank
(22) – Blank
(23) 30A Battery 2 fuse
MAIN FUSE / PRIMARY FUSE
(1)
—Blank
(2)
—Blank
(3)
10AFont fog light
(4)
—A/c compressor relay
(5) 50A Ignition switch fuse
(6)
50ABattery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9)
—Blank
(10) — Radiator fan relay
(11) — Blank
(12) — Blank
(13) — Blank

7-25
INSPECTION AND MAINTENANCE
53MH0-74E
The main fuse, primary fuses and some of
the individual fuses are located in the
engine compartment. If the main fuse
blows, no electrical component will func-
tion. If a primary fuse blows, no electrical
component in the corresponding load
group will function. When replacing the
main fuse, a primary fuse or an individual
fuse, use a Maruti Genuine replacement.
To remove a fuse, use the fuse puller pro-
vided in the fuse box. The amperage of
each fuse is shown in side the fuse box
cover.
60G111
NOTE:
Make sure that the fuse box always carries
spare fuses and fuse puller.
Fuses under the Dash Board
68KH078
ALTO 800
53M-09-043
(14) 80A All electric load
(15) — Blank
(16) — Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A Air compressor fuse
(20) — Fuel pump relay
(21) 7.5AAutomated Manual Tran-
saxle (if equipped)
(22) 40AAutomated Manual Tran-
saxle pump (if equipped)
(23) 30A Battery 2
WA R N I N G
If the main fuse or a primary fuse
blows, be sure to have your vehicle
inspected by an authorized MARUTI
SUZUKI dealer. Always use a genuine
MARUTI replacement. Never use a
substitute such as a wire even for a
temporary repair, or extensive electri-
cal damage and a fire can result.
EXAMPLE
BLOWNOK
EXAMPLE

7-26
INSPECTION AND MAINTENANCE
53MH0-74E
ALTO K10
53M-09-044
53M-09-045
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) – Blank
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) – Blank
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) 7.5AAutomated Manual Tran-
saxle 2 (if equipped)
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) 7.5A IG1 SIG
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI dealer.
EXAMPLE

8-6
EMERGENCY SERVICE
53MH0-74E
Towing
If you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
2-Wheel Drive (2WD) Manual Transaxle
or Automated Manual Transaxle
Manual transaxle vehicles or Automated
Manual Transaxle may be towed using
either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the
ground. Before towing, make sure that
the parking brake is released.
2) From the rear, with the rear wheels
lifted and the front wheels on the
ground, provided the steering and
drivetrain are in operational condition.
Before towing, make sure that transaxle
is in neutral, the steering wheel is
unlocked (the ignition key should be in
the “ACC” position), and the steering
wheel is secured with a clamping
device designed for towing service.
If the Starter Does Not
Operate
1) Try turning the ignition switch to the
“START” position with the headlights
turned on to determine the battery con-
dition. If the headlights go excessively
dim or go off, it usually means that
either the battery is flat or the battery
terminal contact is poor. Recharge the
battery or correct battery terminal con-
tact as necessary.
2) If the headlights remain bright, check
the fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the vehi-
cle inspected by your authorized MAR-
UTI SUZUKI dealer.
If the Engine is Flooded
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine. (Do not operate the starter motor
for more than 15 seconds).
NOTICE
To help avoid damage to your vehicle
during towing, proper equipment and
towing procedures must be used.
NOTICE
After shifting the auto gear shift gear-
shift lever to the “N” position, always
check the gear position indicator in
the instrument cluster shows the “N”
position to make sure that the
transaxle is disengaged.
If the transaxle cannot be put in neu-
tral, turn the key from the “OFF” to
the “ON” position, and move the auto
gear shift gearshift lever from “N” to
“D”, “M” or “R”, then back to “N”
again. Then turn the key from the
“ON” to the “OFF” position.
These procedures may help put the
transaxle in neutral. If the transaxle
still cannot be put in neutral, you can-
not tow the vehicle without using a
towing dolly.
NOTICE
The steering column is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing. Always unlock the steering
wheel before towing.