2013 SUZUKI ALTO light

2-37
BEFORE DRIVING
53MH0-74E
With tachometer
53M-04-099
Clock (1) (if equipped)
The clock is shown when the ignition
switch is in the “ON” position.
To set the clock, follow the instructions
below.
Hold in the indication selector and meter
illumination control knob (3) for more
than 2 seconds. Push the indication
selector and meter illumination control
knob (3) to advance the minute display
while the minute display is flashing.
Release the indication selector and
meter illumination control knob (3) for 5
seconds to set the minute display.
The hour display flash after the minute
display is set. Push the indication selec-tor and meter illumination control knob
(3) to advance the hour display. Release
the indication selector and meter illumi-
nation control knob (3) for 5 seconds to
set the hour display.
Odometer/Trip meter (2)
The odometer/trip meter is shown when
the ignition switch is in the “ON” position.
The odometer records the total distance
the vehicle has been driven. The trip meter
can be used to measure the distance trav-
eled on short trips or between fuel stops.
53M-04-100
When the ignition switch is turned to “ON”
with the lighting switch is in the “OFF” posi-
tion, the display shows three types of indi-
cation; odometer (A), trip meter A (B), trip
meter B (C) and clock (D). Push the
“MODE” knob (3) quickly to switch the indi-
cation among the four.
53M-04-101
WA R N I N G
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
EXAMPLE

2-38
BEFORE DRIVING
53MH0-74E
When the ignition switch is turned to “ON”
and the position lights, tail lights and/or the
headlights are on, the display shows four
types of indication; odometer (A), trip
meter A (B), trip meter B (C), clock (D) and
indication of illumination intensity (E). Push
the “MODE” knob (3) quickly to switch the
indication among the five. When the indica-
tion shows (E), you can control the meter
illumination intensity. Refer to “Meter illumi-
nation control” section below for details on
how to dim or brighten the meter illumina-
tion.
53M-04-102
To reset the trip meter to zero, hold in the
“MODE” knob (3) for about 2 seconds.Meter illumination control
53M-04-103
When the display shows the indication of
illumination intensity (E), you can dim or
brighten the meter illumination.
To change the meter illumination bright-
ness, continue to hold in the “MODE” knob
(3). The indication will change as shown in
the illustration. The illumination gets dim-
mer then returns to the brightest condition
after it reaches the dimmest.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the brightness of the
instrument panel lights will be reinitialized.
Readjust the brightness according to your
preference.
Lighting Control Lever
53M-04-104EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE

2-39
BEFORE DRIVING
53MH0-74E
Lighting Operation
Ty p e 1
53M-04-105
Ty p e 2
53M-04-106
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions:OFF (1)
All lights are off.
(2)
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
(3)
Front position lights, tail lights, license
plate light, instrument lights and head
lights are on.
Ty p e 1
53M-04-107
Ty p e 2
53M-04-108
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE

2-40
BEFORE DRIVING
53MH0-74E
Headlight Leveling Switch
53M-04-109
Level the headlight beam according to the
load condition of your vehicle by turning
this switch. The chart below shows the
appropriate switch position for different
vehicle-load conditions.
Turn Signal Control Lever
53M-04-110
Turn Signal Operation
With the ignition switch in the “ON” posi-
tion, move the lever up or down to activate
the right or left turn signals.
Normal turn signal
Ty p e 1
53M-04-111
Move the lever all the way upward or down-
ward to signal. When the turn is com-
pleted, the signal will cancel and the lever
will return to its normal position.
Ty p e 2
53M-04-112
Vehicle
Load
ConditionSwitch Position
Alto 800 Alto K10
Petrol CNG Petrol CNG
Driver only0000
Driver + 1
passenger
(in front
seat)0000
Driver + 4
passen-
gers, No
cargo1111
EXAMPLE
Driver + 4
passen-
gers,
Cargo
added2NA3NA
Driver +
Full cargo3NA4NA
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE
EXAMPLE
EXAMPLE

2-41
BEFORE DRIVING
53MH0-74E
Lane change signal
Ty p e 1
53M-04-113
Ty p e 2
53M-04-114
Sometimes, such as when changing lanes,
the steering wheel is not turned far enough
to cancel the turn signal. For convenience,
you can flash the turn signal by moving the
lever part way and holding it there. The
lever will return to its normal position when
you release it.
Hazard Warning Switch
53MH0227
Push in the hazard warning switch to acti-
vate the hazard warning lights. All turn sig-
nal lights and both turn signal indicators
will flash simultaneously. To turn off the
lights, push the switch again.
Use the hazard warning lights to warn
other traffic during emergency parking or
when your vehicle could otherwise become
a traffic hazard.
Windshield Wiper and Washer
Lever
65D611
Wiper and Washer Operation
When the ignition switch is in the “ON”
position, you can use the wiper/washer
lever or switch (if equipped).
EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE

2-42
BEFORE DRIVING
53MH0-74E
Windshield Wipers
53MH0228
To turn the windshield wipers on, move the
lever down to one of the three operating
positions. In the “INT” position, the wipers
operate intermittently. The “INT” position is
very convenient for driving in mist or light
rain. In the “LO” position, the wipers oper-
ate at a steady low speed. In the “HI” posi-
tion, the wipers operate at a steady high
speed. To turn off the wipers, move the
lever back to the “OFF” position.
Windshield Washer
53MH0229
To spray windshield washer fluid, pull the
lever toward you. The windshield wipers
will automatically turn on at low speed if
they are not already on and the “INT” posi-
tion is equipped.
INT
LO
HI
OFF
EXAMPLE
WA R N I N G
• To prevent windshield icing in cold
weather, turn on the defroster to
heat the windshield before and
during windshield washer use.
• Do not use radiator antifreeze in
the windshield washer reservoir. It
can severely impair visibility when
sprayed on the windshield, and can
also damage your vehicle’s paint.
EXAMPLE
NOTICE
To help prevent damage to the wind-
shield wiper and washer system
components, you should take the fol-
lowing precautions:
• Do not continue to hold in the lever
when there is no windshield
washer fluid being sprayed or the
washer motor can be damaged.
• Do not attempt to remove dirt from
a dry windshield with the wipers or
you can damage the windshield
and the wiper blades. Always wet
the windshield with washer fluid
before operating the wipers.
• Clear ice or packed snow from the
wiper blades before using the wip-
ers.
• Check the washer fluid level regu-
larly. Check it often when the
weather is bad.
• Only fill the washer fluid reservoir
3/4 full during cold weather to allow
room for expansion if the tempera-
ture falls low enough to freeze the
solution.

3-1
OPERATING YOUR VEHICLE
53MH0-74E
Exhaust Gas Warning
52D334
Daily Inspection Checklist
Before Driving
60A187S
1) Make sure that windows, mirrors, lights,
and reflectors are clean and unob-
structed.
2) Visually check the tires for the following
points:
– the depth of the tread groove
– abnormal wear, cracks and damage
– loose wheel nuts
– existence of foreign material such as
nails, stones, etc.
Refer to “Tires” in “INSPECTION AND
MAINTENANCE” section for details.
3) Look for fluid and oil leaks.
NOTE:
It is normal for water to drip from the air
conditioning system during use.WA R N I N G
Avoid breathing exhaust gases.
Exhaust gases contain carbon mon-
oxide, a potentially lethal gas that is
colorless and odorless. Since carbon
monoxide is difficult to detect by
itself, be sure to take the following
precautions to help prevent carbon
monoxide from entering your vehicle.
• Do not leave the engine running in
garages or other confined areas.
(Continued)
EXAMPLE
WA R N I N G
(Continued)
• Do not park with the engine run-
ning for a long period of time, even
in an open area. If it is necessary to
sit for a short time in a parked vehi-
cle with the engine running, make
sure the air intake selector is set to
“FRESH AIR” and the fan is at high
speed.
• Avoid operating the vehicle with
the tailgate or trunk open. If it is
necessary to operate the vehicle
with the tailgate or trunk open,
make sure all windows are closed,
and the blower is at high speed
with the air intake selector set to
“FRESH AIR”.
• To allow proper operation of your
vehicle’s ventilation system, keep
the air inlet grille in front of the
windshield clear of snow, leaves, or
other obstructions at all times.
• Keep the exhaust tailpipe area clear
of snow and other material to help
reduce the buildup of exhaust
gases under the vehicle. This is
particularly important when parked
in blizzard conditions.
• Have the exhaust system inspected
periodically for damage and leaks.
Any damage or leaks should be
repaired immediately.
EXAMPLE

3-2
OPERATING YOUR VEHICLE
53MH0-74E
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint
(if equipped).
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened your seat belts.
10)Make sure that all warning lights come
on as the key is turned to the “ON” posi-
tion.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Windshield washer fluid level
5) Battery solution level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See “Alllatches, hinges & locks” of “CHASSIS
AND BODY” in the “Periodic Mainte-
nance Schedule” in the “INSPECTION
AND MAINTENANCE” section for lubri-
cation schedule.
Once a month, or each time you fill your
fuel tank, check the tire pressure using a
tire pressure gauge. Also check the tire
pressure of the spare tire.Engine Oil Consumption
It is normal for the engine to consume
some engine oil during normal vehicle
operation.
The amount of engine oil consumed
depends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed during high-speed
driving and when there is frequent acceler-
ation and deceleration. Under high loads,
your engine also will consume more oil.
A new engine also consumes more oil,
since its pistons, piston rings and cylinder
walls have not yet become conditioned.
New engines reach the normal level of oil
consumption only after approximately 5000
km (3000 miles) driving.
Oil consumption:
Max. 1.0 L per 1000 km
When judging the amount of oil consump-
tion, note that the oil may become diluted
and make it difficult to accurately judge the
true oil level.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km or more of driving. This is
because the oil is gradually becoming
diluted with fuel or moisture, making it
appear that the oil level has not changed.
WA R N I N G
Make sure the hood is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.