2013 SUZUKI ALTO overheating

2-32
BEFORE DRIVING
53MH0-74E
Electric Power Steering Light
(if equipped)
53M-04-077
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.
NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
Oil Pressure Light
53M-04-078
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. Thelight will come on and remain on if there is
insufficient oil pressure. If the light comes
on when driving, pull off the road as soon
as you can and stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your MARUTI
SUZUKI dealer before you drive the vehi-
cle again.
Charging Light
53M-04-079
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. The
light will come on and remain on if there is
something wrong with the battery charging
system. If the light comes on when the
engine is running, the charging system
should be inspected immediately by your
MARUTI SUZUKI dealer.
High Engine Coolant Temperature
Warning Light
53M-04-080
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-
tions that may lead to actual overheating. If
NOTICE
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the Oil Pressure
Light to indicate the need to add
oil. Be sure to periodically check
the engine oil level.

2-33
BEFORE DRIVING
53MH0-74E
the light stays on without blinking, then the
engine is overheating. Follow the instruc-
tions in the “If the Engine Overheats” of
“EMERGENCY SERVICE” section.
Immobilizer System Light
53M-04-081
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. If this
light blinks with the ignition switch turned to
“ON”, there may be something wrong with
the immobilizer system. Ask your MARUTI
SUZUKI dealer to have the system
inspected.
Door Lock Canceller Indicator Light
(if equipped)
53M-04-082
This indicator light will come on and keep
blinking continuously if there is some prob-
lem with door lock canceller system. Have
the vehicle inspected by MARUTI SUZUKI
authorized dealer.
NOTE:
In case door lock wiring and/or motor
are
damaged, Door Lock Canceller Indicator
Light will not blink.
Gear Shift Indicator (if equipped)Manual Transaxle
53M-04-083
This indicator informs about upshifting or
downshifting the gear while the vehicle is
running.There are three indications:
Upshift Indicator
This symbol indicates that lower gear posi-
tion is selected for vehicle’s current speed
and / or engine revolution. Changing to
higher gear position is recommended.
Stay Indicator
This symbol indicates that current gear
position is optimal for vehicle’s current
speed and / or engine revolution. No gear
shifting is required.
NOTE:
While driving in optimal gear position, the
upshift/downshift indicator does not
appear.
Downshift Indicator
This symbol indicates that higher gear
position is selected for the vehicle’s current
speed and / or engine revolution. Changing
to lower gear position is recommended.
NOTICE
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.

3-6
OPERATING YOUR VEHICLE
53MH0-74E
Pedal
Manual Transaxle
80J2121
Auto Gear Shift
53M05009
Clutch Pedal (1)
(For manual transaxle)
The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages
the clutch.
Brake Pedal (2)
Your MARUTI SUZUKI vehicle is equipped
with front disc brakes and rear drum
brakes. Depressing the brake pedal
applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-
mal condition caused by environmental
factors such as cold, wet, snow, etc.
Accelerator Pedal (3)
This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
(2)(1)
(3)
EXAMPLE
EXAMPLE
WA R N I N G
Do not drive with your foot resting on
the clutch pedal. It could result in
excessive clutch wear, clutch dam-
age, or unexpected loss of engine
braking.
WA R N I N G
If brake squeal is excessive and
occurs each time the brakes are
applied, you should have the brakes
checked by your MARUTI SUZUKI
dealer.
WA R N I N G
Do not “ride” the brakes by applying
them continuously or resting your
foot on the brake pedal. This will
result in overheating of the brakes
which could cause unpredictable
braking action, longer stopping dis-
tances, or permanent brake damage.

3-10
OPERATING YOUR VEHICLE
53MH0-74E
76MH0A057
NOTE:
• If 1st gear cannot be engaged even
though the gearshift lever has been
shifted from the “N” to the “D” position,
the system will re-try shifting automati-
cally. This will take some time, noise
may be heard from the gears, and shift-
ing gear shock may occur. However,
they do not indicate a malfunction.
• The “N” indicator will flash, the depress
brake pedal indicator will come on and a
warning buzzer (long pulse sound) will
sound if any of the following cases
occur;
– If you shift the gearshift lever from the
“N” to the “D” position without depress-
ing the brake pedal
– If the system is unable to re-try shifting
You should depress the brake pedal and
shift the gearshift lever to “N” position,
then shift to “D” again.
3) Release the parking brake and brake
pedal.
4) Depress the accelerator pedal slowly.
WA R N I N G
• While driving the vehicle, do not
shift the gearshift lever to the “N”
position. The engine brake may not
work and you may get involved in
an unexpected accident. If you
return the gearshift lever from “N”
to “D” because of unintended shift-
ing, the gear position will be shifted
according to the current vehicle
speed.
• Always keep your foot on the brake
pedal while stopped with the
engine running. This operation pre-
vents the vehicle from moving due
to unintended activation of the
creeping function.
NOTICE
If the gearshift lever cannot shift into
any position, or the gear is changed
to “N” position automatically when
the vehicle speed becomes less than
10 km/h, there may be a system mal-
function. In this case, ask your MAR-
UTI SUZUKI dealer to inspect the
Auto Gear Shift system as soon as
possible.
NOTICE
Do not operate the system as
described below. The life cycle of the
clutch may be reduced.
• Using the accelerator pedal to hold
the vehicle on an uphill slope with
the gearshift lever in the “D” or “M”
position. If you perform this opera-
tion for a certain period of time, a
warning buzzer will sound.
• Shifting the gearshift lever to the
“D”, “M” or “R” position while rac-
ing the engine.
• Driving at low speed using a high
gear.
• Holding the vehicle on an uphill
slope using the creeping function.
If you perform this operation for a
certain period of time, a warning
buzzer will sound.
NOTICE
Operate your Automated Manual
Transaxle vehicle with one foot only.
driving your automated manual
transaxle vehicle with accelerator
and brake pedals depressed together
will cause overheating of the clutch.

3-13
OPERATING YOUR VEHICLE
53MH0-74E
Starting off:
1) Start the engine as instructed in “Start-
ing the engine” in this section.
2) With your foot on the brake pedal, shift
the gearshift lever to the “M” position.
When the gearshift lever is shifted to
the “M” position, the gear will be shifted
to 1st. Before starting off, always make
sure that the intended gear is engaged
by checking the gear position indicator,
then depress the accelerator pedal.NOTE:
• If 1st gear cannot be engaged even
though the gearshift lever has been
shifted from the “N” to the “M” position,
the system will re-try shifting automati-
cally. This will take some time, noise
may be heard from the gears, and shift-
ing gear shock may occur. However,
they do not indicate a malfunction.
• The “N” indicator will flash, the depress
brake pedal indicator will come on and a
warning buzzer (long pulse sound) will
sound if any of the following cases
occur;
– If you shift the gearshift lever from the
“N” to the “M” position without
depressing the brake pedal
– If the system is unable to re-try shifting
You should depress the brake pedal and
shift the gearshift lever to “N” position,
then shift to “M” position again a few
seconds later.
3) Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
NOTICE
• If the gearshift lever cannot shift
into any position, or the gear is
changed to “N” position automati-
cally when the vehicle speed
becomes less than 10 km/, there
may be a system malfunction. In
this case, ask your MARUTI SUZUKI
dealer to inspect the Auto Gear Shift
system as soon as possible.
• The manual (M) mode does not
upshift even if the engine speed
reaches the rev-limit.
• The system will not allow shifting up
or down to a gear that would cause
engine over-revving or under-rev-
ving.
• If frequently driving at low speed
using a high gear position, the life
cycle of the clutch may be reduced.
• Frequent downshifting (more than 3
positions consecutively) causes the
reduction of transaxle life.
WA R N I N G
Always keep your foot on the brake
pedal or pull up the parking lever
while stopped with the engine run-
ning. These operations prevent the
vehicle from starting due to unin-
tended activation of the creeping
function.
NOTICE
Do not operate the system as
described below. The life cycle of the
clutch may be reduced.
• Using the accelerator pedal to hold
the vehicle on an uphill slope oper-
ation with the gearshift lever in the
“M” or “D” position. If you perform
this operation for a certain period
of time, a warning buzzer will
sound.
• Shifting the gearshift lever to the
“M”, “D” or “R” position while rac-
ing the engine.
• Driving at low speed using a high
gear.
• Stopping on a slope using the
creeping function. If you perform
this operation for a certain period
of time, a warning buzzer will
sound.
NOTICE
Operate your Automated Manual
Transaxle vehicle with one foot only.
driving your automated manual
transaxle vehicle with accelerator
and brake pedals depressed together
will cause overheating of the clutch.

4-1
DRIVING TIPS
53MH0-74E
68PHM4001
Running-in Catalytic Converter
80G106
The purpose of the catalytic converter is to
minimize the amount of harmful pollutants
in your vehicle’s exhaust. Use of leaded
fuel in vehicles equipped with catalytic
converters is prohibited, because lead
deactivates the pollutant-reducing compo-
nents of the catalyst system.
The converter is designed to last the life of
the vehicle under normal usage and when
unleaded fuel is used. No special mainte-
nance is required on the converter. How-
ever, it is very important to keep the engine
properly tuned. Engine misfiring, which
can result from an improperly tuned
engine, may cause overheating of the cat-
alyst. This may result in permanent heat
damage to the catalyst and other vehicle
components.
WA R N I N G
• WEAR YOUR SEAT BELTS AT ALL
TIMES. Even though air bags may
be equipped at the front seating
positions, the driver and all pas-
sengers should be properly
restrained at all times, using the
seat belts provided. Refer to the
“Seat Belts and Child Restraint
Systems” section for instructions
on proper use of the seat belts.
• Never drive while under the influ-
ence of alcohol or other drugs.
Alcohol and drugs can seriously
impair your ability to drive safely,
greatly increasing the risk of injury
to yourself and others. You should
also avoid driving when you are
tired, sick, irritated, or under
stress.
NOTICE
The future performance and reliabil-
ity of the engine depends on the care
and restraint exercised during its
early life. It is especially important to
observe the following precautions
during the initial 960 km of vehicle
operation.
• After starting, do not race the
engine. Warm it up gradually.
• Avoid prolonged vehicle operation
at a constant speed. Moving parts
will break in better if you vary your
speed.
• Start off from a stop slowly. Avoid
full throttle starts.
• Avoid hard braking, especially
during the first 320 km of driving.
• Do not drive slowly with the
transaxle in a high gear.
• Drive the vehicle at moderate
engine speeds.
• Do not tow a trailer.
EXAMPLE

4-5
DRIVING TIPS
53MH0-74E
If Your Vehicle Gets Stuck
If your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between a forward range (or first gear
for manual transaxle) and reverse. This
will create a rocking motion which may
give you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting. Do not race
the engine. Excessive wheel spin will
cause the tires to dig deeper, making it
more difficult to free the vehicle.
2) If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your authorised Maruti
Suzuki workshop or a roadside assis-
tance service. If a towing service is not
available in an emergency, your vehicle
may be temporarily towed by a towing
cable or chain secured to the towing
hook either on the front of the vehicle or
on the rear of the vehicle. Refer to
“Frame Hooks” in the “OTHER CON-
TROLS AND EQUIPMENT” section.
Driving On Wet Roads
WA R N I N G
Do not allow anyone to stand near
the vehicle when you are rocking it,
and do not spin the wheels faster
than an indicated 40 km/h on the
speedometer. Personal injury and/ or
vehicle damage may result from spin-
ning the wheels too fast.
NOTICE
Do not continue rocking the vehicle
for more than a few minutes. Pro-
longed rocking can cause engine
overheating or transaxle damage.
CAUTION
• When driving on wet roads, avoid
driving through large amount of
standing water on the road. Large
amount of water entering the
engine compartment may cause
damage to the engine and or elec-
trical components.
• If stuck in deep water, do not start
till water level drops.
• Water is incompressible substance,
water inside engine is harmful to
the engine.
WA R N I N G
• In addition to following the driving
tips in this section, it is important
to observe the following precau-
tions.
• Make sure your tires are in good
condition and always maintain the
specified tire pressure. Refer to
“Tires” in the “INSPECTION AND
MAINTENANCE”
• Do not use tires other than those
specified by MARUTI SUZUKI.
Never use different sizes or types
of tires on the front and rear
wheels. For information regarding
the specified tires, refer to the Tire
Information Label located on the
driver’s door lock pillar.
• Never use oversized tires or spe-
cial shock absorbers and springs
to raise (jack up) your vehicle. This
will change the handling character-
istics. Oversized tires may also rub
against the vehicle body over
bumps, causing vehicle damage or
tire failure.
•After driving through water, test the
brakes while driving at a slow
speed to see if they have main-
tained their normal effectiveness. If
the brakes are less effective than
normal, dry them by repeatedly
applying the brakes while driving
slowly until the brakes have
regained their normal effective-
ness
.

5-27
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Selecting a USB device mode
Press the Media Source Mode button to
select USB mode (1).
53M-07-075
Selecting a folder
Press the Folder Up button (7) to select
next folder. Press the Folder Down button
(6) select previous folder.
Selecting a track
Press the Up button (9) to listen to the
next track.
Press the Down button (8) twice to listen
to the previous track. When the Down
button (8) is pressed once, the track cur-
rently being played will start from the
beginning again.Fast forwarding/Rewinding a track
Hold down the Up button (9) to fast for-
ward the track.
Hold down the Down button (8) to fast
rewind the track.
If you keep pressing the UP (9)/DOWN
button(8) until the beginning or ending of
the disc, the unit release the fast-for-
ward/rewind operation and plays the first
track.
Scan play
File Scan
Press the SCAN button (2). The first 10
seconds of each file is play in sequence.
Folder Scan
press the SCAN button (2) for 1 second or
longer. The first 10 seconds of the first file
in each folder stored in the USB is played
in sequence.
NOTE:
To cancel the scan play, press the SCAN
button (2) again or eject the USB.
Random playback
Track random
Press the RDM button (4). the random indi-
cator “RDM” will light. The tracks in the
loaded USB device will be played in ran-
dom order.
Folder random
Press the RDM button (4) for 1 second or
longer. The random indicator “RDM and
FOLD.” will light. The tracks in the current
folder will be played in random order.
NOTE:
To cancel random playback, press the
RDM button (4) again or eject the USB.NOTICE
Do not connect any USB device other
than a USB memory or a USB audio
player. Do not connect multiple USB
devices to the USB connector using a
USB hub, etc. Supplying power to
multiple USB devices from the con-
nector could cause overheating and
smoking.