2013 SSANGYONG KORANDO brake

8712-03
No engine operation
When the START/STOP button is pressed at the vehicle speed of 3 km/h or less, the SKM turns off
the IGN relay to stop the engine.
When the vehicle speed is 3 km/h or more or no speed signal is input, the SKM performs the
following functions: 1.
2.
Vehicle status Conditions
3 km/h or faster - When the START/STOP switch is pressed for 3 seconds
or more, the ignition status is changed from IGN to ACC.
- If the engine START/STOP switch is pressed again, the
ignition status is changed from ACC to IGN.
Abnormal vehicle speed
(No or abnormal CAN signal)- When the START/STOP switch is pressed for 3 seconds
or more, the ignition status is changed from IGN to ACC.
- If the engine START/STOP switch is pressed again, the
ignition status is changed from ACC to Power OFF.
(DTC set)
When the START/STOP button is pressed and held with IGN ON, the ignition status is changed to
OFF. When the START/STOP button is pressed briefly, the ignition status is changed to ACC ON. 3.
ACC ON to Power OFF
The SKM changes the ignition status to OFF from ACC ON when:
the engine START/STOP button is pressed with the brake pedal released after the ignition status is
changed from IGN ON to ACC ON.
the REKES LOCK or passive LOCK signal is input with ACC ON.
the driver door is opened with ACC ON.
(Driver door open signal input through B-CAN)
12 minutes have passed with ACC ON. 1.
2.
3.
4.Condition for starting request transmission 8.
ACC ON: Gear selector lever (P/N), Brake switch ON, START/STOP switch signal
IGN ON: Vehicle in stationary, Gear selector lever (P/N), Brake switch ON, START/STOP
switch ON -
-
Condition for canceling starting request 9.
At engine starting completed -

10. START/STOP SWITCH CONTROL
1) Power Status
Ignition status indicator on START switch
Status Turning-ON conditions
OFF IGN OFF, IGN ON & engine ON
GreenEngine can be started by START/STOP switch operation/Engine is cranking
(IGN OFF & brake switch ON, ACC ON & brake switch ON, IGN ON & brake
switch ON)
Amber ACC ON
Red IGN ON & engine OFF, error
START switch indicator output
Powersta
tusPower OFF
ACC ON IGN
ONEngine
start
statusEngine
can be
startedError Remarks
Door
closedDoor
open
Figure
Indicator
statusOFF OFF Amber Red OFF GreenRed
Flash
Illuminatio
n
controlOFF TIME Controlled by SKM LED
The indicator flashes 5 times at intervals of 0.5 sec. ON/0.5 sec. OFF when an error occurs.
When all the doors are closed with B+, the indicator does not flash. -
-
START/STOP switch indicator control
START/STOP switch indicator
ON OFFDoor coupled function
When the driver door is opened, the indicator comes
on (the indicator remains on while the door is open).
When the room lamp is turned off, the indicator goes
out immediately.
The indicator goes out 10 seconds after the driver door
is closed.
The indicator is reset when the driver door is opened.
Tail lamp coupled function -
1)
2)
3)
4)
-

(10) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(11) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(12) SKM alert priority
1 Smart key out alarm Outside
1
2 Smart key reminder alarm Outside
3 Smart key verification failure alarm Inside
2 4 Transponder verification fail alert Inside
5 Smart key battery low voltage alert Inside
6 Transmission position alert Inside
7 SKM error alert Inside
8 Brake alert Inside
9 Clutch alert Inside
10 Smart key slot reminder alarm Inside 1
Warning deactivation conditions
Warning transmission conditions
Warning deactivation conditions
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-

Indicator
(amber)
Brake warning lamp (brake fluid)
ABS warning lamp
Passenger air bag disable indicator
Indicator
(red)
Indicator
(amber)
Indicator
(red)
EPS
Indicator
(amber)
Immobilizer indicator
This indicator comes on when the passenger air bag OFF switch is operated.
This indicator comes on the immobilizer (transponder) is not certified. This lamp comes on when the parking brake is applied or the brake fluid
is insufficient.
If this lamp doesn't go off after the parking brake is released, check the
brake fluid level first and then fluid leakage. -
-
This warning light comes on when the ignition switch is turned to ON
and should go out if the system is normal -
This indicator comes on when the EPS system is faulty.

8010-01
Indicator
(green)
Hazard indicator
ECO indicator
Cruise control indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
4WD LOCK indicator
Indicator
(red)
4WD check warning lamp
This indicator comes on when the cruise control system is activated.
This indicator goes off when the brake pedal is depressed. (auto cruise
deactivated)
This warning lamp comes on when the 4WD LOCK switch is pressed.
This indicator goes off when pressing the switch again.
This warning lamp comes on when the 4WD system is defective. This indicator comes on when the hazard warning flashers are switched on.
(applies to STD class)
This indicator comes on when the ECO cruise system is activated.
This indicator goes off when the brake pedal is depressed. (ECO
deactivated)

8) Buzzer
Specifications
Function Signal
Part name PKM17EPP-2002-B0 (MURATA, Piezoelectric Sound Components)
Permitted input voltage 25 VP-P or less
Operating temperature
Storage temperature
Sound pressure level 70 dB/min (3 Vp-p, 2 kHz, square wave, 10 cm)
Capacitance
Priority of instrument cluster buzzer output
If there are multiple signals at a time, the operation should be completed by the priority.
Priority
ItemBuzzer output
time
Operating condition
ON OFF
1 PAS See PAS
2 ESP 0.1sec 0.1secInstrument cluster buzzer output signal is
received from ABS/ESP
3Engine overheat
warning lamp0.5sec 0.5sec
4Water separator
warning light0.5sec 0.5secWater separator warning light ON with
IGN ON
5 Parking brake 2.8sec 1.5secParking brake applied depending on
vehicle speed

Pin No.Message
Operating condition
Domestic Export
Smart key
warningThis message comes on the LCD display, if the smart
key is not in the vehicle when the door is open and
closed in the ignition ON or ACC mode.
This message comes on the LCD display for approx. 10
seconds, if the ignition switch is pressed when the smart
key is not in the vehicle.
This message comes on the LCD display for approx. 10
seconds, if the smart key verification fails after inserting
the smart key into the key holder.
LCD display shows this message and Smart key
reminder sounds for 10 seconds when you open the
in the Smart key holder.
This message informs the driver that the brake pedal
should be depressed and the ignition switch be pressed
in order to start the engine, if the ignition is switched to
ACC mode for more than one time when the driver keeps
pressing the ignition switch without depressing the brake
pedal.
LCD display shows this message when you press the
ignition switch without depressing the clutch pedal.
This message comes on for approx. 10 seconds to
inform the driver that the ignition switch should be
pressed with the shift lever in P in order to start the
engine.
When a Smart key is inside the vehicle and all doors are
closed, LCD display shows this message if you press the
Lock button on the other Smart key.
Pin No. Message Operating condition

(8) Stop lamp operation process
Depressing the brake pedal lights on the stop lamps by a signal from the stop lamp switch fitted to the
brake pedal and releasing the brake pedal turns off it.
(9) Backup lamp operation process
When shifting the TGS lever into the "R" position with the ignition switch "ON", the backup lamps come
on. If the lever is placed in other positions, the lamps go off.
High mounted stop lamp
Rear combination stop lamp
Backup lamp