2013 SSANGYONG KORANDO wiper fluid

8710-01
Windshield wiper and washer switch function
The wiper system operates the wiper and washer using the signals from the multi-function switch, and
receives rain sensing signal from the rain sensor unit.
4. WIPER CONTROL
1. MIST
When the wiper switch is pulled up and
released, the wiper cycles once and then
returns to the park position. -
2. OFF
Stops the windshield wiper operation. -
3. AUTO
When the wiper switch is set to the AUTO
position, the wiper speed is adjusted
automatically according to the amount of
rain measured by the rain sensor mounted
on the windshield. -
4. LO/HI
When the wiper switch is set to the LO
position, the wiper speed is decreased.
When the switch is set to the HI position, the
wiper speed is increased. -
5. Wiper speed control switch
The wiper speed can be adjusted with this
switch as follows when the wiper switch is in
AUTO position.
* FAST: increases wiper speed
* SLOW: decreases wiper speed -6. AUTO washer switch
When the AUTO washer switch is pressed, the
washer fluid is sprayed once and the wiper is
operate 4 times. Then, the fluid is sprayed once
again with 3 wiping operations. -
7.
When the switch is fully turned, washer fluid will
be sprayed onto the rear window glass and the
wiper will also operate. When the switch is
and turn off the wiper and washer. -
8. OFF
Rear wiper is not in operation. -
9. Rear wiper operation (Intermittent) -
10. Rear wiper operation (Normal Speed) -
Type B
Type A
TYPE A
TYPE B
Rear wiper operation
When the switch is fully turned, washer fluid will be sprayed onto the rear window glass
and the wiper will also operate. When the switch is released, it will return to the Rear
Wiper Operation mode and only the wiper will keep operating.9. INT
10. ON

8710-01
Washer switch input during rain sensor coupled operation
The windshield washer switch is in the ON position.
The communication with the rain sensor is ignored. (can misread washer fluid as rain drops)
The washer coupled wiper operation is activated (T1).
After that, the wiper is operated by rain sensor coupled operation (T2).
However, if the washer switch signal is received the washer relay is activated and wiper relay remains
activated, when the data coupled with rain sensor indicates continuous wiper operation. A.
B.
C.
D. Operation 1.
- The rain sensor coupled data is not continuous wiper operation.
Basic conditionsIntermittent operation with IGN ON and wiper AUTO switch in ON position
Even though the wiping system is in washer coupled wiper mode, the operating data are sent to rain
sensor from the BCM.

8510-00
position and release it, the windshield
wipers operate one wiping cycle. The
wipers will operate continuously if the
switch is held in this position.
Front automatic wiping speed control switch
The interval of wiping speed can be adjusted by turning the
control knob upward or downward when the windshield
wiper switch is in AUTO position.
Fast: Fast interval
Slow: Slow interval Wipers are not in operation.
Operates automatically
according to the vehicle speed
and amount of rainfall.
Continuous wipe, fast operation Continuous wipe, slow
operation MIST
OFF
AUTO
LO
HI Auto washer switch
If pressing the switch when the wiper
switch turns to the "OFF" position,
washer fluid is sprayed once and
wiper operates 4 times.
After a while, washer fluid is sprayed
once more and the wiper operates 3
times. Wiper switch

Rear wiper switch
Type B
Type AWindshield Washer Operation
lever toward you to spray washer
fluid on the windshield and to
operate the wipers 1~3 cycles.
Pull the lever briefly (for less than 0.6
seconds): One wiping cycle with
washer spray
Pull and hold the lever for more than
0.6 seconds: Three wiping cycles
with washer spray
The spray and wiper operation will
continue until you release the lever.
TYPE B
When the switch is fully turned, washer fluid will be sprayed onto the rear window
glass and the wiper will also operate. When the switch is released, it will return to
Rear wiper is not in operation.
TYPE A
INT
Rear wiper operation
(Intermittent)
ON
Rear wiper operation
(Normal Speed)
Rear wiper operation
When the switch is fully turned, washer fluid will be sprayed onto the rear window
glass and the wiper will also operate. When the switch is released, it will return to
the Rear Wiper Operation mode and only the wiper will keep operating.

7810-00
1. WIPER CONTROL
2. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial engine
start is made. This may cause the wiper blades to wear prematurely. Therefore, other than rainy
days, set the switch to the OFF position. Especially during the winter time, check if the wiper blades
are not frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the windshield
can be scratched and the wiper blades can wear prematurely. Use the wiper with the washer fluid
when the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of the
wipers. -
-
-
-Wiper mist & washer coupled wiper
Auto washer coupled wiper
Rain sensor coupled wiper operation (LIN)
Speed sensitive intermittent wiper
Wiper low/high control
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to work
irregularly. Therefore, in this case, replace the wiper blade with a new one. -
-
-
-
-Irregular operation (abrupt operation)
When cleaning the windshield over the sensor with damp clothes, the wiper may operate suddenly. It
could cause serious injury. Make sure to place the wiper switch to the OFF position and ignition switch
OFF when not in use.

1. WIPER AND WASHER SYSTEM
1) AUTO Washer Coupled Wiper Function
If you press the AUTO washer switch briefly with the ignition key ON and INT-AUTO switch "OFF", the
washer motor is operated for about 2 seconds to spray washer fluid once after the switch is turned ON
and the wiper relay is turned ON for 4 cycles. After that, the washer motor is operated for about 2
seconds to spray the washer fluid again and the relay is turned ON for 3 cycles and then the relay is
turned OFF.
2) Rear Washer Fluid Supply System
The front washer fluid reservoir supplies the rear washer fluid without additional washer fluid reservoir. Operating part for rear
wiper/washer
AUTO washer
switch (press)
Washer motor

4. WIPER AND WASHER OPERATION
1) Windshield Wiper Control Function
position and release it, the windshield wipers
operate one wiping cycle. The wipers will
operate continuously if the switch is held in this
position.
Front automatic wiping speed control switch
turning the control knob upward or downward when the
windshield wiper switch is in AUTO position.
Fast: Fast interval
Slow: Slow interval Wipers are not in operation.
Operates automatically according to
the vehicle speed and amount of
rainfall.
Continuous wipe, fast
operation Continuous wipe, slow operation
MIST
OFF
AUTO
LO
HI
Front auto washer switch
When you press this switch with the
washer fluid will be sprayed and the
wiper will automatically operate 4 times.
Then, the fluid will be sprayed again and
the wiper will automatically operate 3
times.

7810-00
When holding the front washer switch at ON position for more than 0.6 seconds with IGN ON, the
wiper relay is activated 0.5 seconds after. The wiper stops after three more wipes since that the
washer switch is turned to "OFF" position. 1.
2) Windshield Washer Control Function
(1) Windshield washer coupled wiper
Wiper and Washer Coupled Operation
Pull the switch briefly (for less than 0.6 sec.)
: One wiping cycle
Pull and hold the switch for more than 0.6 sec.
: Three wiping cycles with washer fluid spray