2013 SKODA OCTAVIA bluetooth

Select sourceFig. 8
Main menu/CD mode
First read and observe the introductory information and safety warn-
ings
on page 18.
Accessing main menu in media mode
›
Press the button MEDIA.
Selecting the audio source ■ CD - Changes to an inserted CD » page 21
■ SD - Changes to an inserted SD memory card 1)
» page 22
■ USB - Changes to a connected external audio source at the USB in-
put 1)
» page 23
■ AUX - Changes to an external audio source connected to the AUX in-
put » page 23
■ BT - Changes to a connected external audio source via Bluetooth ®
1)
» page 23
Symbols in the displaySymbolImportanceSound is mutedA CD is inserted in the device driveDisplays a connected Bluetooth ®
device / Repeat track or folderRandom play ,  ,  ,  , Currently selected audio sourceAuto-play function for 10 seconds

Sources and file formats supported
First read and observe the introductory information and safety warn-
ings
on page 18.
Supported sources
SD memory cardSD, SDHC, SDXCCD driveAudio CD (up to 80 min), CD-R and CD-RW (with a capacity
of up to 700 MB)USB devicesUSB stick, USB MP3 player, HDD (without special software)Other external
sourcesPortable playback devices with AUX connection, MTP (MSC)
players, Bluetooth ®
players
At the time of publication, the device has been tested with most products and
media available in the various markets. However, it is possible that some devices,
media or files will be unreadable or unplayable.
Supported files
Audio filesCodec type (file
formats)MPEG-1/2 (layer 3)Windows Media Audio 7, 8, 9 and 10File suffixmp3wmaPlaylistsm3u, pls, wpl, m3u8; asx 
1)
Operating an external audio source is possible only with certain restrictions and depends on the type
of connected device.
19Audio

■Never expose the CD to direct sunlight.■Only write on the CD with appropriate writing tools.■
Do not stick anything to the CD!
Note
■Poor or unpaved road surfaces and severe vibrations may cause the CD to jump.■Damp (condensation) may affect the device in cold weather or after showers.
This can lead to playback jumps or impair the play function. In such cases, wait
until the moisture has dissipated.■
If a CD is dirty, it should never be cleaned using a circular motion, but rather
from the inside out. Use a soft, lint-free cloth for cleaning. In the case of heavy
contamination, we recommend cleaning the CD with a standard CD cleaner and
leaving to dry.
■
In certain circumstances, CDs protected by copyright or self-made CD-Rs and
CD-RWs may not play, or may only play to a limited extent.
■
The national copyright laws that apply in your country must be observed.
■
The CD player does not include any parts that need to be serviced or repaired. In
the case of a defective CD player, please visit a specialist garage.

SD memory card
First read and observe the introductory information and safety warn-ings
on page 18.
The device can be used to play audio files saved on an SD memory card.
Inserting an SD memory card
›
Push the SD memory card into the memory card slot
14
with the cut-off edge to
the front right until it “locks into place” » Fig. 1 on page 5. The play function will
start automatically.
Removing an SD memory card
›
Press the SETUP button
→ System → Remove SD card safely .
›
Press the inserted SD memory card. The SD memory card moves into the eject
position.
SD memory card empty or data not readable
If an SD memory card is inserted and no data or no legible data has been stored
on the card, the device will not be switched to the SD memory card mode after
loading.
Due to differing quality requirements from different card manufacturers, it is not
always possible to guarantee the playback from SD memory cards.
It may not be possible to play some or all files on the SD memory card, or their
playback may be limited.
CAUTION
■ Only use one-part SD memory cards. If using an SD memory card with an adapt-
er (multipart SD memory cards), vehicle vibrations can cause the SD memory card can fall out of the adapter while driving, and individual card parts can remainstuck in the device.■
We recommend using SD memory cards of class 4 and higher. This guarantees
the fastest possible access to the audio files.
■
Always store the SD cards in suitable cases to protect them from dirt, dust and
other forms of damage.

Bluetooth ®
player
First read and observe the introductory information and safety warn- ings
on page 18.
Audio files can be played and managed on the device via the A2DP and AVRCP
Bluetooth ®
player profiles (audio streaming).
Conditions for successful connection and playback. The Bluetooth ®
player must be paired with your device » page 27.
The audio files must have one of the supported formats » page 19.
Note
■
Bluetooth profiles A2DP and AVRCP (1.0 - 1.3) are supported.■We recommend adjusting the volume on the portable player to the maximum
level.■
The supported playback functions depend on the type of Bluetooth ®
player be-
ing used.

22Audio

Communication
Telephones and two-way radio systems
Introduction
This chapter contains information on the following subjects:
Main menu
25
Error messages
25
Phonebox
26
First and foremost, pay attention to the safety instructions » page 4 , Important
notes .
The Telephone menu is available when the following conditions are met:
The ignition is switched on.
The Bluetooth ®
function on the device is switched on.
ŠKODA permits the operation of mobile phones and two-way radio systems with
a professionally installed external aerial and a maximum transmission power of
up to 10 watts.
Please ask at a specialist workshop about installing and operating mobile phones
and two-way radio systems that have a transmission power of more than 10 W.
Operating mobile phones or two-way radio systems may interfere with the func-
tionality of the electronic systems in your vehicle.
The reasons for this are as follows:
› no external aerial;
› incorrectly installed external aerial;
› transmission power greater than 10 watts.
After the device is switched on, the system attempts to connect to the most re-
cently connected mobile phone 1)
.
WARNING■ The national legal regulations for using a mobile phone in a vehicle must be
observed.■
If a mobile phone or a two-way radio system is operated in a vehicle without
an external aerial or with an incorrectly installed external aerial, this can in-
crease the strength of the electromagnetic field inside the vehicle.
■
Two-way radio systems, mobile phones or mounts must not be installed on
airbag covers or within the immediate deployment range of the airbags.
■
Never leave a mobile phone on a seat, on the dash panel or in any area
where it can become a projectile during a sudden braking manoeuvre, an acci-
dent or a collision — risk of injury.
■
The Bluetooth ®
function must be switched off by a specialist workshop be-
fore the vehicle is transported by air.
CAUTION
The range of the Bluetooth ®
connection to the hands-free system is restricted to
the vehicle interior. The range is dependent on local conditions, e.g. obstacles be-
tween the devices and mutual interferences with other devices. If your mobile
phone is in a jacket pocket, for example, this can lead to difficulties when estab-
lishing a connection with the hands-free-system or transferring data.
Note
We recommend that the installation of mobile phones and two-way radio sys-
tems in a vehicle be carried out by a specialist garage.1)
With some phones, it is necessary to set the connection to the device as "authorised" in order for the
automatic connection to be successful. If this is not set, the system will prompt you for a confirma-
tion each time you attempt to connect to the mobile phone.
24Communication

Main menuFig. 10
Main menu
First read and observe the introductory information and safety warn- ings
on page 24.
Call up the main menu
›
Press the button TELEPHONE.
If a mobile phone is connected to the hands-free system, the telephone mode
main menu is displayed » Fig. 10.
Functions in the Telephone main menu
■ Dial - Direct entry of a phone number » page 29
■ Contacts - Displays the phone book » page 30
■ Calls - Displays the call list » page 31
■ Redial - Redials the last outgoing call » page 31
The display shows the name of the mobile phone service provider 1)
, the name of
the connected phone and various symbols.
SymbolMeaningCharge status of the phone battery a)Signal strengtha)Roaming (before the name of the mobile network provider) a)Displays a connected Bluetooth®
deviceSymbolMeaningMissed callCurrent calla)
This function is only supported by some mobile phones.
If no mobile phone is connected to the hands-free system, the message Please
connect a mobile telephone. is displayed. » page 26, Connecting the mobile tel-
ephone to the hands-free system

Error messages
First read and observe the introductory information and safety warn-
ings
on page 24.
If there are problems with the availability of the network or with the Bluetooth ®
function, the following messages appear on the device display screen.
MessageMeaning
Provider unknown
The name and code number of the mo-
bile phone network operator are un- known or are not offered by the mobilephone.Network searchThe mobile phone searches for availa-
ble GSM networks.No networkThe mobile phone is not connected to the GSM network.
Rejected by network
The mobile phone network operator
has rejected the connection (e.g. not
enough mobile phone credit, SIM card
blocked, roaming not available).Bluetooth off. Do you want to switch
it on?Bluetooth ®
is switched off in the Setup
menu. Select Yes to switch Bluetooth ®
on.Telephone function deactivated.Bluetooth ®
was switched off in a spe-
cialist garage using a diagnostic device. 
1)
In some cases, the name of the network operator may be replaced by an international identification
number.
25Communication

MessageMeaningInternal Bluetooth module not work-
ing.A Bluetooth ®
error a)
.Please switch on the ignition to use
telephone functions.The phone function is not available be-
cause the ignition is off. Switch on the
ignition.Telephone is currently not available
\nbecause an update is active.The phone function is not available be-
cause Bluetooth ®
is being updated.Battery of the device … is almost run
down.Warning prior to switching off the mo-
bile phone due to a dead battery.a)
By removing the ignition key, the Bluetooth ®
function is reset to the initial settings after approxi-
mately 2 minutes. The function should be restored after carrying out this step.

Phonebox
Fig. 11
Phonebox
First read and observe the introductory information and safety warn- ings
on page 24.
At the bottom of the storage compartment in the front center console is an in-
duction plate connected to a GSM roof antenna roof - the Phonebox.
Function
When the mobile phone is inserted into the Phonebox, the phone signal increases in strength by about 20%. This reduces the level of phone battery discharge and
the electromagnetic radiation inside the vehicle.
Inserting the mobile phone into the Phonebox›Press on the edge of the lid A in the direction of the arrow, and open the stor-
age compartment.›
Place the mobile phone in the storage compartment
B
with its back on the in-
duction panel.
›
Press on the edge of the lid
A
in the opposite direction from the arrow, and
close the storage compartment » .
The Phonebox cannot be used as an alternative to connecting the mobile phone
with the device.
WARNINGFor safety reasons, the storage compartment must always be closed when
driving.
Note
■ Protective cases or cases around the mobile phone placed in the storage com-
partment may interfere with the phone signal strength.■
Metallic objects such as coins or keys under the mobile phone can affect the
phone signal strength.

Connecting the mobile telephone to the hands-free
system
 Introduction
This chapter contains information on the following subjects:
Pairing process from the hands-free system
27
Pairing from the mobile phone
28
Fast connection to another paired mobile phone
28
Automatic connection
29
Disconnection
29
First and foremost, pay attention to the safety instructions » page 4 , Important
notes .
To connect a mobile phone with the hands-free system, the two devices must be paired. 
26Communication

The pairing can be initiated from the hands-free system as well as from the mo-
bile phone.
Prerequisites for successful pairing: The ignition is switched on.
The Bluetooth ®
function for the hands-free system is switched on » page 13.
The Bluetooth ®
function for the mobile phone is switched on.
The visibility of the hands-free system is switched on » page 13.
The visibility of the mobile phone is switched on.
During the pairing process, no other mobile phone may be connected with the hands-free system.
The devices are paired with each other » page 26.
When pairing from the mobile phone, follow the instructions in the owner's
manual of the mobile phone.
The hands-free system is indicated as SKODA_BT_... in the Bluetooth ®
device to
be connected. ... is replaced with the last four symbols of the VIN code of your ve-
hicle. You can change the name of the hands-free system.
Possible symbols for found or paired devicesSymbolMeaningDevices that support the functionality of the hands-free sys- tem (Bluetooth ®
profile HFP) a)Bluetooth®
players (Bluetooth ®
profiles A2DP and AVRCP) b)a)
HFP is a Bluetooth
®
profile that supports the functionality of the hands-free system.
b)
A2DP and AVRCP are Bluetooth ®
profiles that support multimedia functions.
Note
The maximum number of connected devices is 20 If a new device is paired after
the maximum number has been reached, the paired device that was least recent- ly used will be automatically deleted.Pairing process from the hands-free system
First read and observe the introductory information given on page 26.›
Press the SETUP button
→ Telephone → Bluetooth setup → Found devices .
If the desired mobile phone is found in the list of Bluetooth ®
devices, then pro-
ceed as follows.
›
Select the mobile phone for pairing by turning the menu button
2
» Fig. 1 on
page 5.
›
Confirm the function Connect.
If the desired mobile phone is not found in the list of Bluetooth ®
devices, or if the
No contact available message appears, confirm the function Search and wait un-
til the system has finished searching.
The search can be cancelled by pressing the BACK
button. A list will be displayed
showing the devices that were found before the search was cancelled.
If the mobile phone supports the Bluetooth ®
profiles A2DP or AVRCP, the mes-
sage Do you want to connect the audio profile? appears on the screen, along
with the possible functions 1)
.
■ Yes - The Bluetooth ®
profiles A2DP and AVRCP are connected, allowing the
playback of audio files from the mobile phone
■ No - The A2DP and AVRCP profiles are not connected
The device can pair several Bluetooth ®
players, but only one player can be con-
nected to the device.
Note any pairing requests shown in the Bluetooth ®
player.
The following messages will be displayed on the device display screen, depending
on the type of mobile phone:
6-digit PIN code and the possible functions:
■ Accept - Accepts the displayed PIN code
■ Cancel - Cancels the pairing process
or 

1)
This selection is ignored by some mobile phones, and the A2DP and AVRCP profiles are connected
automatically by them.
27Communication

4-digit PIN code1)
and the possible functions:
■ Accept - Accepts the displayed PIN code
■ Change - To change the PIN code manually
■ Turn the menu button 2
» Fig. 1 on page 5 to navigate within the number
field, and press the menu button
2
to confirm the number selection.
■ Delete - Deletes mistyped PIN code number
■ OK - Accepts the entered PIN code
■ Cancel - Cancels the pairing process
If the hands-free system appears on the display of the mobile phone, enter the PIN within 30 seconds and wait, until the pairing is complete.

Pairing from the mobile phone
First read and observe the introductory information given on page 26.
Pairing
›
Have the mobile phone search for available Bluetooth ®
devices 2)
.
›
Select the hands-free system in the list of Bluetooth ®
devices.
The following messages will be displayed on the device display screen, depending on the type of mobile phone:
6-digit PIN code and the possible functions:
■ Accept - Accepts the displayed PIN code
■ Cancel - Cancels the pairing process
or
Screen for entering the PIN code 1 )
and the possible functions:
■ OK - Accepts the entered PIN code
■ Delete - Changes the entered PIN code
If the hands-free system appears on the display of the mobile phone, confirm the
pairing request and wait until the pairing is complete.

Fast connection to another paired mobile phone
First read and observe the introductory information given on page 26.
If you want to connect the device to another paired mobile phone, the existing
connection does not have to be terminated. The connection to the existing mo-
bile phone is automatically terminated by connecting to another mobile phone.
›
Press the PHONE button in the Telephone main menu.
A list of up to four previously connected mobile phones will appear.
›
Select the mobile phone to be connected with the hands-free system by con- firming the corresponding function key
3
» Fig. 1 on page 5.
The on-screen message Replace the connection with … with a new connection
with …? must be confirmed in order to ensure that the connection is established
successfully.
›
If the desired mobile phone does not appear in the list press the Search key and
search for paired devices.
›
Select the desired phone from the resulting list of paired devices by turning the
menu button
2
.
›
Confirm the connection by selecting Connect.
If the desired mobile phone did not appear in the list of the four previously con-
nected mobile phones and is not in the resulting list of paired devices, then the
mobile phone must be paired with the device » page 27.


1)
The newly entered PIN code must contain between 4 and 16 digits. The same PIN code must be en-
tered on both the hands-free system and the mobile phone.
2)
The hands-free system is indicated as SKODA_BT_... in the Bluetooth ®
device to be connected. ... is
replaced with the last four symbols of the VIN code of your vehicle. You can change the name of the hands-free system.
28Communication

Automatic connectionFirst read and observe the introductory information given on page 26.
After the device is switched on, the system attempts to connect 1)
to the most re-
cently connected mobile phone 2)
. If the connection cannot be established, the
system will then attempt to connect to other previously connected phones one
by one.
The message Automatic connection... appears on the screen during the automat-
ic connection process.
If the phone was found, the following message appears on the screen: Connection successful
Telephone connected
If the phone was not found, the message Please connect a mobile telephone.
appears on the screen.

Disconnection
First read and observe the introductory information given on page 26.
The connection of a mobile phone to the device can be disconnected in one of the
following ways.
› By removing the ignition key (or switching off the ignition and opening the driv-
er's door in vehicles with the KESSY system).
› By disconnecting the hands-free system or switching off the Bluetooth ®
func-
tion on the mobile phone.
› By switching off the Bluetooth ®
function on the device » page 13.
› By disconnecting or deleting the paired device from the list of paired devi-
ces » page 13 .

Telephone functions
Introduction
This chapter contains information on the following subjects:
Enter a phone number
29
Contact list
30
call lists
31
Redialling the previous outgoing call
31
Telephone call
31
Conditions for successfully making telephone calls The ignition is switched on.
The mobile phone is connected to the hands-free system.

Enter a phone number
Fig. 12
Entering a phone number
First read and observe the introductory information given on page 29.
›
Press the button PHONE
→ Dial . 

1)
Provided that the ignition and the Bluetooth®
function are switched on.
2)
With some phones, it is necessary to set the connection to the device as "authorised" in order for the
automatic connection to be successful. If this is not set, the system will prompt you for a confirma-
tion each time you attempt to connect to the mobile phone.
29Communication