2013 Seat Mii light

273
Practical information
Complete operations only in the sequence given:
1.Always take the checklist into account and take the necessary ac-
tions ⇒ page 267.
2.With one hand, press on the number plate light from left to right
and remove it from the bumper ⇒ Fig. 158.
3.Detach the number plate light carefully from the bumper.
4.Turn the bulb holder with the bulb anticlockwise and remove it in
the direction of the arrow ⇒ Fig. 159.
5.Replace the faulty bulb by a new identical bulb.
6.Place the bulb holder in the number plate light and press in the op-
posite direction to the arrow as far as possible ⇒ Fig. 159.
7.
Insert the number plate light carefully into the left edge of the open-
ing on the bumper. During this process, check that the assembly di-
rection of the number plate light is correct, i.e. the spring must be
on the right.
8.Insert the number plate light into the bumper until it audibly clicks
into place.Changing the side turn signal bulb
Fig. 160 Removing the
side turn signal
Fig. 161 Side turn sig-
nal: Changing the bulbs
Complete operations only in the sequence given:
1.Always take the checklist into account and take the necessary ac-
tions
⇒ page 267.
2.With one hand move the side turn signal backwards ⇒ Fig. 160 1.

Vehicle diagramPrior to a journey...While drivingCare, cleaning and mainte-
nanceIf and whenTechnical specifications

276Practical information
How to jump start: description
Fig. 162 Diagram of con-
nections for vehicles
without Start-Stop sys-
tem.
Fig. 163 Diagram of con-
nections for vehicles
with Start-Stop system.
Jump lead terminal connections
1. Switch off the ignition of both vehicles ⇒ 
.2. Connect one end of the
red jump lead to the positive +
termi-
nal of the vehicle with the flat battery A ⇒ Fig. 162.
3. Connect the other end of the red jump lead to the positive ter-
minal +
in the vehicle providing assistance B.
4. For vehicles without Start-Stop system: Connect one end of the
black jump lead to the negative terminal –
of the vehicle pro-
viding assistance B ⇒ Fig. 162.
– For vehicles with Start-Stop system: Connect one end of the
black jump lead X
to a suitable ground terminal, a solid piece
of metal in the engine block, or to the engine block ⇒ Fig. 163.
5. Connect the other end of the black jump lead X
to a solid met-
al component bolted to the engine block or to the engine block
itself of the vehicle with the flat battery. However, connect it to
a point as far as possible from the battery A
.
6. Position the leads in such a way that they cannot come into contact with any moving parts in the engine compartment.
Starting
7. Start the engine of the vehicle with the boosting battery and let it run at idling speed.
8. Start the engine of the vehicle with the flat battery and wait two or three minutes until the engine is “running”.
Removing the jump leads
9. Before you remove the jump leads, switch off the dipped beam headlights (if they are switched on). 

277
Practical information
10.Turn on the heater blower and heated rear window in the vehi- cle with the flat battery. This helps minimise voltage peaks
which are generated when the leads are disconnected.
11.When the engine is running, disconnect the leads in reverse or- der to the details given above.
Connect the battery clamps so they have good metal-to-metal contact with
the battery terminals.
If the engine fails to start, switch off the starter after about 10 seconds and
try again after about half a minute.
WARNING
● Please note the safety warnings referring to working in the engine
compartment ⇒ page 182.
● The battery providing assistance must have the same voltage as the
flat battery (12V) and approximately the same capacity (see imprint on
battery). Failure to comply could result in an explosion.
● Never use jump leads when one of the batteries is frozen. Danger of
explosion! Even after the battery has thawed, battery acid could leak and
cause chemical burns. If a battery freezes, it should be replaced.
● Keep sparks, flames and lighted cigarettes away from batteries, dan-
ger of explosion. Failure to comply could result in an explosion.
● Observe the instructions provided by the manufacturer of the jump
leads.
● Do not connect the negative cable from the other vehicle directly to
the negative terminal of the flat battery. The gas emitted from the battery
could be ignited by sparks. Danger of explosion.
● Do not attach the negative cable from the other vehicle to parts of the
fuel system or to the brake line.
WARNING (Continued)
● The non-insulated parts of the battery clamps must not be allowed to
touch. The jump lead attached to the positive battery terminal must not
touch metal parts of the vehicle, this can cause a short circuit.
● Position the leads in such a way that they cannot come into contact
with any moving parts in the engine compartment.
● Do not lean on the batteries. This could result in chemical burns.
Note
The vehicles must not touch each other, otherwise electricity could flow as
soon as the positive terminals are connected. 
Vehicle diagramPrior to a journey...While drivingCare, cleaning and mainte-
nanceIf and whenTechnical specifications

279
Practical information
Instructions for tow starting
In general, the vehicle should not be started by towing. Jump-starting is
much more preferable ⇒  page 275.
For technical reasons, the following vehicles can not be tow started:
● Vehicles with an automatic gearbox.
● If the vehicle battery is flat, it is possible that the engine control unit
does not operate correctly.
However, if your vehicle must absolutely be tow-started (manual gearbox):
● Engage the 2nd or 3rd gear.
● Keep the clutch pressed down.
● Switch on the ignition and the hazard warning lights.
● Release the clutch when both vehicles are moving.
● As soon as the engine starts, press the clutch and move the gear lever
into neutral. This helps to prevent a collision with the towing vehicle.
CAUTION
When tow-starting, fuel could enter the catalytic converter and damage it. 
Notes on towing
Tow rope or tow bar
When towing, the tow bar is the safest and vehicle friendly way. You should
only use a tow rope if you do not have a tow bar.
A tow rope should be slightly elastic to avoid damage to both vehicles. It is
advisable to use a tow rope made of synthetic fibre or similarly elastic mate-
rial. Only secure the tow rope or tow bar to the towline anchorage or specially
designed fitting.
Towing vehicles with an automatic gearbox
Note the following for a towed vehicle:
●
Make sure the gear selector lever is in the N position.
● Do not drive faster than 50 km/h (30 mph) when towing a vehicle.
● Do not tow further than 50 km (30 miles).
● If a breakdown truck is used, the vehicle must be towed with the front
wheels raised.
Situations in which the vehicle should not be towed
In the following cases, the vehicle should not be towed but transported on a
trailer or special vehicle:
● If the vehicle gearbox does not contain lubricant due to a fault.
● If the battery is flat as the steering cannot be unlocked, as a result, the
electronic steering lock and electronic parking brake cannot be disengaged.
● If the vehicle to be towed has an automatic gearbox and the distance to
be covered is greater than 50 km (30 miles).
Note
The vehicle can only be towed if the steering lock electronic gearbox lock is
deactivated. If the vehicle has no power supply or there is an electric system
fault, the engine must be started using jump leads to deactivate the steer-
ing column electronic gearbox lock. 
Vehicle diagramPrior to a journey...While drivingCare, cleaning and mainte-
nanceIf and whenTechnical specifications

281
Practical information
If the vehicle is towed, with the hazard warning lights on and the ignition
switched on, the turn signal may be used to indicate changes of direction.
Simply operate the turn signal lever as usual. Meanwhile, the hazard warn-
ing lights will go off. When the turn signal lever is returned to the rest posi-
tion, the hazard warning lights will be turned on automatically.
Notes for the driver of the towed vehicle
● Keep the ignition running to prevent the steering wheel from locking
and also to allow the use of the turn signals, horn, windscreen wipers and
washers.
● As the power assisted steering does not work if the engine is not run-
ning, you will need more strength to steer than normally.
● The brake must be depressed must harder as the brake servo does not
operate. Avoid hitting the towing vehicle.
● Note the instructions and information contained in the Instruction Man-
ual for the vehicle to be towed.
Notes for the driver of the towing vehicle
● Accelerate gently and carefully. Avoid sudden manoeuvres.
● Brake well in advance than usual and brake gently.
● Note the instructions and information contained in the Instruction Man-
ual for the vehicle to be towed. 
Vehicle diagramPrior to a journey...While drivingCare, cleaning and mainte-
nanceIf and whenTechnical specifications

284Description of specifications
● Passengers.
● Total equipment.
● Roof load, included in the carrier.
WARNING
Exceeding the maximum authorised weight and the load on the axles
could cause damage to the vehicle, accidents and serious injuries.
● The real load on the axles should never exceed the maximum permit-
ted.
● The load and its distribution in the vehicle have effects on the vehicle
handling and the braking ability. Always drive at a suitable speed.
CAUTION
Distribute the load as uniformly and as low down on the vehicle as possible.
When transporting heavy objects in the luggage compartment, these
should be placed as far forward as possible or over the rear axle to have as
little influence on handling as possible. 
Information on fuel consumption
The consumption and emission values indicated do not refer to one specific
vehicle. They are only to be used to compare the values of the different ve-
hicle versions. The fuel consumption and CO 2 emissions of a vehicle not on-
ly depend on the effective use of fuel. They also depend on your driving
style and other non-technical factors.
Calculation of fuel consumption
Fuel consumption and emission values are determined according to the cur-
rent version of the 715/2007/EC or 80/1268/EEC regulation and are valid
for the vehicle kerb weight. The specifications do not refer to an individualvehicle. To measure the fuel consumption, two measuring cycles are carried
out on a rolling road test bed. The test criteria are as follows:
Urban cycleMeasurement of the urban cycle starts with an engine cold
start. City driving is then simulated at between 0 and 50 km/
h (0 and 31 mph).
Road cycle
In the road cycle simulation, the car undergoes frequent ac-
celeration and braking in all gears, as in normal everyday
driving. The road speed ranges from 0 to 120 km/h (0 and
75 mph).
CombinedThe average combined consumption is calculated with a
weighting of around 37 % for the urban cycle and 63 % for
the road cycle.
CO
2 emis-
sions of the
combinationThe exhaust gases are collected during both driving cycles
to calculate carbon dioxide emissions (urban and road). The
gas composition is then analysed to evaluate the CO 2 con-
tent and other emissions.
Note
The kerb weight may vary according to the vehicle equipment. This could
raise consumption and the CO 2 emissions slightly.
Note
In practice, consumption values could be different to the values calculated
based on the 715/2007/EC or 80/1268/EEC regulations. 

Index
A
AbroadExtended stay abroad with your vehicle . . 234
Sale of vehicle . . . . . . . . . . . . . . . . . . . . . . 234
ABS See "Brake assist systems" . . . . . . . . . . . . 140
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 222, 223
Additional equipment . . . . . . . . . . . . . . . . . . . 224
Adjust Headlight range . . . . . . . . . . . . . . . . . . . . . . 86
Adjustment Correct sitting position . . . . . . . . . . . . . . . . 49
Front seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
rear head restraints . . . . . . . . . . . . . . . . . . . 51
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . 52
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Cleaning dash panel . . . . . . . . . . . . . . . . . 208
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . . 67
Deactivating the front passenger front air-bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Deactivating using the key switch . . . . . . . . 71
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Differences between front passenger front airbag systems . . . . . . . . . . . . . . . . . . . . . 67
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . 70
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Locking the vehicle after airbag deploy-
ment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . 73
Use of child seats . . . . . . . . . . . . . . . . . . . . . 71
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . 208
Air conditioner Air recirculation . . . . . . . . . . . . . . . . . . . . . 169
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Things to note . . . . . . . . . . . . . . . . . . . . . . . 168
User instructions . . . . . . . . . . . . . . . . . . . . 167
Air conditioning system . . . . . . . . . . . . . . . . . . 164 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Air recirculation . . . . . . . . . . . . . . . . . . . . . . . . 169 How it works . . . . . . . . . . . . . . . . . . . . . . . . 169
switch off . . . . . . . . . . . . . . . . . . . . . . . . . . 169
temporarily switch off . . . . . . . . . . . . . . . . 169
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Aluminium care . . . . . . . . . . . . . . . . . . . . . . . . 202
Anodized surfaces . . . . . . . . . . . . . . . . . . . . . . 202
Anti-lock brake system (ABS) . . . . . . . . . . . . . 140
Anti-puncture kit . . . . . . . . . . . . . . . . . . . . . . . . 258
Anti-theft bolts . . . . . . . . . . . . . . . . . . . . . . . . . 248
Anti-theft locking bolts . . . . . . . . . . . . . . . . . . 252
Anti-theft wheel locking bolts . . . . . . . . . . . . . 253
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
ASR
see Brake assist systems . . . . . . . . . . . . . . 140
Assistance systems Brake assist system (BAS) . . . . . . . . . . . . . 140
Cruise control system (CCS) . . . . . . . . . . . . 152
Electronic differential lock system (EDL) . 140
Electronic Stability Programme (ESP) . . . . 139
Hill hold . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Optical parking system (OPS) . . . . . . . . . . 150
Parking aid . . . . . . . . . . . . . . . . . . . . . . . . . 150
Parking distance warning system . . . . . . . 150
Safety Assist (City Safety Assist function) 155
Traction control system (ASR) . . . . . . . . . . 140
Traction Control (TC) . . . . . . . . . . . . . . . . . . 140
Assist systems Anti-lock brake system (ABS) . . . . . . . . . . 140
Audible warnings Control and warning lamps . . . . . . . . . . . . . 15
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Seat belt not fastened . . . . . . . . . . . . . . . . . 57
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Automatic belt retainer . . . . . . . . . . . . . . . . . . . 64
Automatic car wash . . . . . . . . . . . . . . . . . . . . . 198
Automatic consumer disconnection . . . . . . . . 196
automatic gearbox . . . . . . . . . . . . . . . . . . . . . . 124
Automatic gearbox . . . . . . . . . . . . . . . . . . . . . . 129 driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Kickdown . . . . . . . . . . . . . . . . . . . . . . . . . . 131
malfunction . . . . . . . . . . . . . . . . . . . . . . . . 132
289
Index

Safety interlock for ignition key . . . . . . . . . 121
starting on a slope . . . . . . . . . . . . . . . . . . . 131
stopping on a slope . . . . . . . . . . . . . . . . . . 131
Axle loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
B
BAS see Brake assist systems . . . . . . . . . . . . . . 140
Battery Change in the vehicle key . . . . . . . . . . . . . . 31
discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Discharging . . . . . . . . . . . . . . . . . . . . . . . . 242
See Vehicle battery . . . . . . . . . . . . . . . . . . 193
Battery acid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Before consulting a specialised workshop . . . 239
Belt tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Service and disposal . . . . . . . . . . . . . . . . . . 64
Belt tension limiter . . . . . . . . . . . . . . . . . . . . . . . 64
Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Bonnet Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Brake servo . . . . . . . . . . . . . . . . . . . . . . . . . 138
Brake assist systems . . . . . . . . . . . . . . . . . . . . 139
Brake assist system (BAS) . . . . . . . . . . . . . . . . 140
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Specification . . . . . . . . . . . . . . . . . . . . . . . . 141 Brakes
Brake assist systems . . . . . . . . . . . . . . . . . 139
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . 141
Brake fluid level . . . . . . . . . . . . . . . . . . . . . 142
Brake pads . . . . . . . . . . . . . . . . . . . . . . . . . 137
Changing the brake fluid . . . . . . . . . . . . . . 142
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 135
Emergency brake indicator in case of sud-den braking . . . . . . . . . . . . . . . . . . . . . . . 242
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . 136
Running-in brake pads . . . . . . . . . . . . . . . . 137
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . 135
Brake servo . . . . . . . . . . . . . . . . . . . . . . . . 138, 139
Brake system Malfunction . . . . . . . . . . . . . . . . . . . . . . . . 138
Brake systems . . . . . . . . . . . . . . . . . . . . . . . . . 139
Breakdown Securing the vehicle . . . . . . . . . . . . . . . . . 241
Bulb fault See changing bulbs . . . . . . . . . . . . . . . . . . 266
C
Capacities Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Care See "Care of your vehicle" . . . . . . . . . . . . . 197
Vehicle interior . . . . . . . . . . . . . . . . . . . . . . 205
Care of your vehicle Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Caring for paintwork . . . . . . . . . . . . . . . . . . . . . 202
Carrier system . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Catalytic converter . . . . . . . . . . . . . . . . . . . . . . 238
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 237
Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . 237
CCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Central locking . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Central locking button . . . . . . . . . . . . . . . . . 34
locking and unlocking from the exterior . . . 33
locking and unlocking from the inside . . . . 34
"Safe" Deadlock system . . . . . . . . . . . . . . . . 35
Central locking system After airbag deployment . . . . . . . . . . . . . . . 32
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Opening doors individually . . . . . . . . . . . . . 32
Centre console . . . . . . . . . . . . . . . . . . . . . . . 12, 13 Bottom part . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Top part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing Windscreen wiper blades . . . . . . . . . . . . . 201
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . 252 Changing a wheel . . . . . . . . . . . . . . . . . . . 257
Preparations . . . . . . . . . . . . . . . . . . . . . . . . 253
Raising the vehicle . . . . . . . . . . . . . . . . . . . 255
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . 253
Changing bulbs . . . . . . . . . . . . . . . . . . . . . . . . 266 Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Front bumper . . . . . . . . . . . . . . . . . . . . . . . 269
Initial operations . . . . . . . . . . . . . . . . . . . . 267
in the headlights . . . . . . . . . . . . . . . . . . . . 268
Number plate light . . . . . . . . . . . . . . . . . . . 272
Rear lights . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Sea changing bulbs . . . . . . . . . . . . . . . . . . 266
290 Index