2013 RENAULT SCENIC battery

37B-71
MR-372-J84-37B000$576.mif
V11
37B
ELECTRONIC PARKING BRAKE
Fault finding – Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool.
Application conditions: ignition on (forced + after ignition, see Introduction)
Note:
The interpretation of these statuses and parameters is only valid with the
ignition switched on, the statuses and parameters displayed in blue on the
diagnostic tool is information supplied by other computers, which are transmitted via
the multiplex network. If these variables display inconsistent values, make sure that
the multiplex system test has not shown up any faulty connections. Repair the faulty
multiplex connections before looking for a possible problem with the signals.
Each sub-function in this test is associated with a Fault finding chart.
Special notes:
The diagnostic tool may display the message Computer busy when displaying
statuses and parameters. This message is displayed when the parking brake is
applying or releasing the brake, because the computer gives priority to controlling the
motor before transmitting variables. If this message is displayed, exit the current
screen and then return to it.
Order FunctionParameter or Status
Checked or ActionDisplay
and notesFault finding
1Parking brake
operation statusET024:System operationCUSTOMER MODEIf the status displays FACTORY
MODE, the computer is not
operational.
To enter CUSTOMER MODE,
initialise the computer again, by
running command VP011
Computer calibration and
initialisation (see
Replacement of components).
2Computer
electrical supplyET001:+ After ignition
feedIgnition off: ABSENT
Ignition on: PRESENTIn the event of a fault on this
status, refer to the interpretation
of status ET001: + after
ignition supply.
PR001:Battery voltage9.6V not within this range, check the
insulation, continuity and the
absence of interference
resistance on the computer
supplies and earths (see wiring
diagram). If the fault is still
present, carry out fault finding
on the charging circuit (see
Technical Note 6014A,
Checking the charging
circuit).
FPA_V0C_CCONF / FPA_V04_CCONF / FPA_V08_CCONF / FPA_V0D_CCONF / FPA_V11_CCONF
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
MR-372-J84-37B000$576.mif

37B-74
MR-372-J84-37B000$576.mif
V11
FPA
Vdiag No.: 0C, 04, 08,
0D, 11ELECTRONIC PARKING BRAKE
Fault finding – Conformity check37B
SUB FUNCTION: PARKING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool.
Application conditions: ignition on (forced + after ignition, see Introduction)
Note:
The interpretation of these statuses and parameters is only valid with the
ignition switched on, the statuses and parameters displayed in blue on the
diagnostic tool is information supplied by other computers, which are transmitted via
the multiplex network. If these variables display inconsistent values, make sure that
the multiplex system test has not shown up any faulty connections. Repair the faulty
multiplex connections before looking for a possible problem with the signals.
Each sub-function in this test is associated with a Fault finding chart.
Special notes
The diagnostic tool may display the message Computer busy when displaying
statuses and parameters. This message is displayed when the parking brake is
applying or releasing the brake, because the computer gives priority to controlling the
motor before transmitting variables. If this message is displayed, exit the current
screen and then return to it.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Computer
electrical supplyET001:+ After ignition
feedIgnition off: ABSENT
Ignition on:
PRESENTIn the event of a fault on this
status, refer to the interpretation of
status ET001: + after ignition
supply.
PR001:Battery voltage9V parameter, check the insulation,
continuity and the absence of
interference resistance on the
computer supplies and earths
(see wiring diagram). If the fault is
still present, carry out fault
finding on the charging circuit
(see Technical Note 6014A,
Checking the charging circuit).
ET009:Redundant
braking switch
positionLever released:
INACTIVE
Lever pulled to the
second contact (end of
travel):
ACTIVEIf the status does not operate as
specified, use the interpretation
of status ET009 Redundant
braking switch position.
ET010:Release switch
positionLever in rest position
RELEASED
Lever fully pulled and
releasing switch
pressed: PRESSEDIf the status does not operate as
specified, apply the
interpretation of status ET010
Releasing switch position.

37B-97
MR-372-J84-37B000$720.mif
V11
37B
ELECTRONIC PARKING BRAKE
Fault finding – Parameter summary table
Tool parameterDiagnostic tool title
PR001Battery voltage
PR003Slope value
PR004Measured force value
PR005Force setting
PR006Clutch pedal position
PR012Vehicle speed
PR013Rear left-hand wheel speed
PR014Rear right-hand wheel speed
PR015Engine speed
PR017Accelerator pedal position
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
MR-372-J84-37B000$720.mif

37B-105
MR-372-J84-37B000$936.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Fault finding chart
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
ALP1 No dialogue with the computer
NOTESNone.
Try the diagnostic tool on another vehicle.
Check:
– the connection between the diagnostic tool and the diagnostic sensor (wiring in good condition),
– the connection between the diagnostic sensor and the diagnostic socket (lead in good condition),
– the engine and passenger compartment fuses.
Check for + 12 V battery on track 16, and + 12 V after ignition feed on track 1 and an earth on track 5 and on
track 4 of the diagnostic socket.
Repair if necessary.
Disconnect the automatic or electronic parking brake computer connector to check the insulation, continuity
and absence of interference resistance on the following connections:
Automatic parking brake computer connector
track H4
(except Laguna II, Vel Satis and Espace IV) track G4 + 12 V
track H2
(except Laguna II, Vel Satis and Espace IV) track G2 earth
track A4 track 7 of the diagnostic socket (K line)
Repair if necessary (see the vehicle wiring diagram).
AFTER REPAIRCarry out a check using the diagnostic tool.
Deal with any other faults.
FPA_V0C_ALP1 / FPA_V04_ALP1 / FPA_V08_ALP1 / FPA_V0D_ALP1 / FPA_V11_ALP1
ELECTRONIC PARKING BRAKE
Fault finding – Fault finding chart
MR-372-J84-37B000$936.mif

3 7 B - 111
MR-372-J84-37B000$936.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Fault finding chart
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
ALP4 Assisted braking fault (when the engine is stopped)
NOTESOnly consult this customer complaint after a full check using the diagnostic tool
(no present or stored faults).
(see the wiring diagrams technical note for the vehicle concerned).
Check for any potential faults in the ABS computer (see 38C, Anti-lock braking system), the UCH computer
(see 87B, Passenger compartment connection unit) and the injection computer (see 13B, Diesel injection or
17B, Petrol injection) to ensure that they have actually received a request to stop the engine.
Test the application of the electronic parking brake with the engine switched off.
Incorrect signal faults on the multiplex line.
Run a multiplex network test (see88B, Multiplex).
When the engine stalls, the automatic brake application function is not active.
Check the + 12 V supply, the insulation, continuity and the absence of interference resistance on the
following connection:
– connection code BP2
Between the electronic parking brake computer, component code 1217 and the battery, component code 107.
If the continuity is correct, test the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a check using the diagnostic tool.
Deal with any other faults.
FPA_V0C_ALP4 / FPA_V04_ALP4 / FPA_V08_ALP4 / FPA_V0D_ALP4 / FPA_V11_ALP4

37B-112
MR-372-J84-37B000$936.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Fault finding chart
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
ALP5 Impossible to manually release electronic parking brake
NOTESOnly consult this customer complaint after a full check using the diagnostic tool
(no present or stored faults).
(see the wiring diagrams technical note for the vehicle concerned).
Check any incorrect signals on the multiplex line.
Run a multiplex network test (see88B, Multiplex).
Check that the card is correctly inserted for a card reader, scenario 1 (not hands-free).
If not, refer to the fault finding procedure for the UCH (see 87B, Passenger compartment connection unit).
Reposition it, if necessary.
Check that the steering column is unlocked.
Check the + 12 V supply, the insulation, continuity and the absence of interference resistance on the
following connection:
– connection code BP2
Between the electronic parking brake computer, component code 1217 and the battery, component code 107.
If the continuity is correct, test the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Repair if necessary.
Check the operation of the release switch.
Check the continuity of the following connection codes:
– connection code 150P,
– connection code 150N,
– connection code 150B,
– connection code 150G,
Between the control unit of the electronic parking brake lever, component code 1216 and the electronic parking
brake computer, component code 1217.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a check using the diagnostic tool.
Deal with any other faults.
FPA_V0C_ALP5 / FPA_V04_ALP5 / FPA_V08_ALP5 / FPA_V0D_ALP5 / FPA_V11_ALP5

37B-115
MR-372-J84-37B000$936.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Fault finding chart
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
ALP8 The electronic parking brake does not apply correctly on a slope
NOTESOnly consult this customer complaint after a full check using the diagnostic tool
(no present or stored faults).
(see the wiring diagrams technical note for the vehicle concerned).
Check that the vehicle is correctly gripping the ground.
Check that the vehicle is not outside the limits.
Check the + 12 V supply, the insulation, continuity and the absence of interference resistance on the
following connection:
– connection code BP2
Between the electronic parking brake computer, component code 1217 and the battery, component code 107.
If the continuity is correct, test the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Repair if necessary.
Check the condition of the brake pads (wear, fitting, insufficient running in, etc.).
Replace if necessary.
Check the condition of the brake callipers.
Repair if necessary.
Check the fitting of the pressure plate between the electronic parking brake and the brake calliper.
Refit if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a check using the diagnostic tool.
Deal with any other faults.
FPA_V0C_ALP8 / FPA_V04_ALP8 / FPA_V08_ALP8 / FPA_V0D_ALP8 / FPA_V11_ALP8