2013 RENAULT KANGOO sensor

17B-171V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent
with the pedal position.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
INACTIVECheck the condition and fitting of the clutch pedal position sensor, component
code
675 (see MR 388 (Logan and Sandero), Mechanical, 37A, Mechanical
component controls, Clutch pedal position sensor: Removal - Refitting or MR
451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical,
37A, Mechanical component controls, Clutch pedal: Removal - Refitting).
Remove the clutch pedal position sensor, component code 675 (see MR 388
(Logan and Sandero), Mechanical, 37A, Mechanical component controls,
Clutch pedal position sensor: Removal - Refitting or MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical
component controls, Clutch pedal: Removal - Refitting).
Check the insulation between connections MAM (for Logan, Sandero, Duster) or
M (for Thalia 2/Symbol 2, Clio II F 6) and 86D of component 675 with the switch in
the rest position.
– Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor,
component code 675 (see MR 388 (Logan and Sandero), Mechanical, 37A,
Mechanical component controls, Clutch pedal position sensor: Removal -
Refitting or MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6),
Mechanical, 37A, Mechanical component controls, Clutch pedal: Removal -
Refitting).
V42_V04_ET405/V42_V05_ET405/V42_V06_ET405/V42_V14_ET405/V42_V16_ET405/V42_V18_ET405

17B-172V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405
CONTINUED
INACTIVE
(CONTINUED)
Then check the continuity and absence of interference resistance of the following
connection:
–86D between components 120 and 675.
Check that the earth is correct on connection MAM (for Logan, Sandero, Duster) or
M (for Thalia 2/Symbol 2, Clio II F 6) of component 675.
If the connection(s) are faulty and there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
ACTIVECheck the condition and fitting of the clutch pedal position sensor.
Remove the clutch pedal position sensor, component code 675 (see MR 388 (Logan
and Sandero), Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting or MR 451 (Duster) or MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical component
controls, Clutch pedal: Removal - Refitting) and check the insulation between
connections MAM and 86D of component 675 with the switch in the rest position.
– Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor, component
code 675 (see MR 388 (Logan and Sandero) or 451 (Duster) and MR 423 (Thalia
2/Symbol 2), Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting or MR 451 (Duster) or MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical component
controls, Clutch pedal: Removal - Refitting).

17B-176V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET759BRAKING MULTIPLEX SIGNAL DETECTED
STATUS DEFINITIONABSENT: This status indicates that the braking multiplex signal detected is absent.
PRESENT: This status indicates that the braking multiplex signal detected is present.
INTERMEDIATE: This status indicates that the braking multiplex signal detected is
intermediate.
Conformity check: Engine stopped, ignition on or engine running.
Vehicle under + after ignition feed.
– Parking brake released,
– Gear lever in 1
st.
Neither the brake pedal nor the clutch pedal depressed.
Check status ET759.
PRESENT -
INTERMEDIATECheck the correct position and the conformity of the brake pedal sensor.
Run fault finding on the UCH domain (see 87B, UCH).
"ABSENT"The brake pedal sensor is correct.
V42_V04_ET759/V42_V05_ET759/V42_V06_ET759/V42_V14_ET759/V42_V16_ET759/V42_V18_ET759

17B-177V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET836TDC SENSOR SIGNAL
STATUS DEFINITIONDETECTED: This status indicates that the TDC sensor signal is detected.
NOT DETECTED: This status indicates that the TDC sensor signal is not detected.
Conformity check: Engine stopped, ignition on or engine running.
NOT DETECTEDIn the event of a fault, refer to the interpretation of fault DF120 Engine speed sensor
signal.
V42_V04_ET836/V42_V05_ET836/V42_V06_ET836/V42_V14_ET836/V42_V16_ET836/V42_V18_ET836

17B-180V2 MR-376-X76-17B050$120.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
OCR*: Opening cyclic ratioTool
ParameterDiagnostic tool title
PR002 Alternator charge
PR015Engine torque
PR030Accelerator pedal position
PR037Refrigerant pressure
PR041 Turbocharging pressure
PR055Engine speed
PR059 Inlet air temperature
PR064Coolant temperature
PR071 Computer feed voltage
PR084 Coolant temperature sensor voltage
PR089Vehicle speed
PR097Motorised throttle lower stop programmed value
PR098Upstream oxygen sensor voltage
PR099Downstream oxygen sensor voltage
PR102Canister bleed solenoid valve OCR*
PR118Measured throttle position gang 1
PR119Measured throttle position gang 2
PR138Richness correction
PR139 Operating adaptive richness
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR215 Sensor supply voltage no. 1
PR216 Sensor supply voltage no. 2
PR312Inlet manifold vacuum
PR313 Linearised manifold pressure
PETROL INJECTION
Fault finding – Parameter summary table

17B-181V2 MR-376-X76-17B050$120.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool
ParameterDiagnostic tool title
PR344 Pressure sensor voltage
PR427Average pinking signal
PR429Measured throttle position
PR444Integral idling speed regulation correction
PR446Upstream O2 sensor heating resistance
PR447Downstream O2 sensor heating resistor
PR448Ignition advance
PR469Cylinder 1 pinking value
PR471Cylinder 2 pinking value
PR473Cylinder 3 pinking value
PR475Cylinder 4 pinking value
PR492Motorised throttle position setpoint
PR538Measured throttle voltage, gang 2
PR539Measured throttle voltage gang 1
PR606Adaptive idling speed correction
PR624Richness regulation programming offset
PR625Richness regulation programming gain
PR743Alcohol level estimated in the tank
PR770Camshaft offset
PR814Number of active heating resistors
PR831Combustion misfiring counter

17B-182V2 MR-376-X76-17B050$120.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Refriger.*: refrigerant
Syncro*: Synchronisation
OCR*: Opening cyclic ratio
CS*: CamshaftTool
ParameterDiagnostic tool title
PR832Combustion misfiring counter
PR833Combustion misfiring counter
PR834Combustion misfiring counter
PR847Inlet air temperature sensor voltage
PR872Refriger.* pressure sensor voltage
PR876CS* dephaser solenoid valve control OCR*
PR877Estimated engine oil temperature
PR887Motorised throttle safe mode programmed value
PR931Raw turbocharging pressure
PR1026Crankshaft synchro.* loss counter
PR1029 Alternator power
PR1116LPG pressure
PR1129 Brake contact no.1 duration
PR1153 Brake contact no.2 duration
PR1198LPG temperature
PR1232Number of engine rotations

17B-185V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR037REFRIGERANT PRESSURE
PA R A M E T E R
DEFINITIONThis parameter indicates the refrigerant pressure in bar.
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
The refrigerant pressure must be between 2 bar < PR037 < 27 bar.
Check the cleanliness and condition of the refrigerant pressure sensor and its connections, component code
1202 and the injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Using the universal bornier in place of the computer, check for insulation and continuity on the following
connections:
–38Y between components 120 and 1202,
–38X between components 120 and 1202,
–38U between components 120 and 1202.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the refrigerant pressure sensor, component code 1202 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
(See MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air
conditioning: Precautions for repair) and (see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), Mechanical, Air conditioning: Parts and consumables for the repair).
If the fault is present, check the air conditioning circuit (see MR 388 (Logan and Sandero), MR 451 (Duster) or
MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air conditioning: Check).
V42_V04_PR037/V42_V05_PR037/V42_V06_PR037/V42_V14_PR037/V42_V16_PR037/V42_V18_PR037