2013 RENAULT KANGOO engine

17B-252
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 3 Throttle valve check
NOTESNone.
Check that parameter PR444 Idle speed regulation integral correction is between:
5 N.m < PR444 < 10 N.m (K4M, K7M engine) or -5 N.m < PR444 < 5 N.m (D4D, F4R and K4M engine of Duster).
The attempt is made with the engine idling and warm (75°C), without any electrical consumers switched on. The
value of PR444 must be read at least 20 minutes after the engine coolant temperature has reached 75°C.
If the value of PR444 is greater than 10 N.m (K4M, K7M engine) or 5 N.m (D4D, F4R and K4M engine of Duster),
reprogram the throttle valve using command RZ031 Throttle stop programming.
If the value of PR444 is less than -5 N.m, check the fitting of the throttle and check for possible air leaks (see MR
388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST3/V42_V05_TEST3/V42_V06_TEST3/V42_V14_TEST3/V42_V16_TEST3/V42_V18_TEST3

17B-253
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 4 Fuel vapour absorber solenoid valve check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness, mounting, possible leaks and the hoses of the fuel vapour absorber solenoid valve,
component code 371 (see MR 388, Mechanical, 14A, Emission control, Fuel vapour recirculation circuit:
Check or MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), Mechanical, 14A, Emission control, Fuel vapour
absorber: Removal - Refitting).
Listen for the operation of the solenoid valve while running command AC017 Canister bleed solenoid valve.
With the engine idling, disconnect the pipe at the solenoid valve inlet and check that there is no suction on your
finger. (These steps allow the sealing of the solenoid valve to be checked for air tightness.)
Check the cleanliness and condition of the canister bleed solenoid valve connector, component code 371 and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3FB between components 371 and 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo
VLL) or 983 (for Clio II F 6),
–3BB between components 371 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST4/V42_V05_TEST4/V42_V06_TEST4/V42_V14_TEST4/V42_V16_TEST4/V42_V18_TEST4

17B-254
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 4
CONTINUED
With the ignition on, check for + 12 V on connection 3FB of component 371.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the resistance of the fuel vapour absorber bleed solenoid valve.
If the resistance of the fuel vapour absorber bleed solenoid valve is not between: 24  < X < 30  or 22  < X <
30  (F4R engine on Duster) between 0°C and 40°C, replace the fuel vapour absorber bleed solenoid valve (see
MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 14A, Emission control, Fuel vapour absorber: Removal - Refitting).
If the fault is still present, contact the techline.

17B-256
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 5
CONTINUED
Check the continuity, insulation, and absence of interference resistance on the following connections:
For Logan, Sandero, Duster:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 1047,
For Thalia 2/Symbol 2, Kangoo VLL:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 238,
For Clio II F 6:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 983.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the supply of the solenoid valve using a test light, by running command AC224 Additional petrol circuit
pump relay.
Check the internal resistance of the solenoid valve, component code 1640 on the connector of the computer,
component code 120. Its value must be between: 24  < X  30  12  £ X £ 16  (Duster F4R engine) or 22 
X  30
 (Duster K4M engine) (between 0°C and 40°C). If the resistance is not correct, replace the solenoid
valve (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6)
or MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel pump of the additional fuel tank: Removal -
Refitting).
If the fault is still present, contact the techline.

17B-259
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 8 Accelerator pedal potentiometer check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the variation in PR055 Engine speed when depressing the accelerator pedal (with the engine running).
Stop the engine and switch on the ignition. Without action on the pedal, check that the voltage correction of circuit 1:
–PR147 Pedal potentiometer voltage gang 1 is less than 817 mV and
–PR148 Pedal potentiometer voltage gang 2 is less than 440 mV.
Next, in the "full load" position, check the circuit 1 voltage PR147, which must be greater than 4185 mV, and
PR148, which must be greater than 2013 mV.
Also check the pedal position in the following cases:
– "position zero" (PR030 Accelerator pedal position = 0)
– "Full load" (PR030 = 1).
Stop the engine and then switch on the ignition.
With the vehicle under + after ignition feed, measure the voltage between the following connections:
–3LR and 3LT of component 921,
–3LU and 3LV of component 921.
If the value is not between 4.75 VX5.25 V, check the insulation, the continuity and the absence of
interference resistance of the following connections:
–3LR between components 120 and 921,
–3LT between components 120 and 921,
–3LU between components 120 and 921,
–3LV between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LS between components 120
and 921,
–3LW between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST8/V42_V05_TEST8/V42_V06_TEST8/V42_V14_TEST8/V42_V16_TEST8/V42_V18_TEST8

17B-264
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 10 TDC sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the sensor fitting (connectors, mountings, etc.) (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol Injection,
Crankshaft position sensor: Removal - Refitting).
Switch on the ignition, check the change of the engine rotation speed using parameter PR055 Engine speed. The
value must be between 0 rpm and more than 120 rpm when the starter is operating.
With the engine running, accelerate to obtain different engine rotation speeds and check that the engine speed
correctly changes in relation to the accelerations.
If PR055 varies, the sensor is sound.
Check the cleanliness and condition of the TDC sensor, component code 149 and of the injection computer
connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
V42_V04_TEST10/V42_V05_TEST10/V42_V06_TEST10/V42_V14_TEST10/V42_V16_TEST10/V42_V18_TEST10

17B-265
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 10
CONTINUED
Check the resistance of the TDC sensor between connections 3BL and 3BG on the injection computer
connector side, component code 120 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Petrol injection
computer: Removal - Refitting).
The resistance must be between 175   X  295  or 200  < X < 270  (F4R engine of Duster) (between 0°C
and 40°C). If the value is not correct, replace the sensor (see MR 388 (Logan and Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol Injection,
Crankshaft position sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3BL between components 120 and 149,
–3BG between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-266
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 11 Pinking sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Start the engine and let it idle. Next, check that PR427 Average pinking signal is equal to 0.
With the engine idling, check that parameters PR469 Cylinder 1 pinking value, PR471 Cylinder 2 pinking value,
PR473 Cylinder 3 pinking value, PR475 Cylinder 4 pinking value are all 0.
Check the cleanliness and condition of the pinking sensor connector, component code 146 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the resistance of the pinking sensor, component code 146 between connections 3DQ and 3S on the
injection computer connector side, component code 120 (see MR 388 (Logan and Sandero). MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection,
Petrol injection computer: Removal - Refitting).
The resistance must be greater than 10 M or between 559 k < X < 561 k (F4R engine of Duster).
If the resistance value is not correct, replace the pinking sensor, component code 146 (see MR 388 (Logan and
Sandero). MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Petrol injection: List and location of components).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3DQ between components 120 and 146,
–3S between components 120 and 146.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_TEST11/V42_V05_TEST11/V42_V06_TEST11/V42_V14_TEST11/V42_V16_TEST11/V42_V18_TEST11