17B-161V2 MR-376-X76-17B050$100.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool status Diagnostic tool title
ET001Computer + After ignition
ET038Engine
ET039Brake pedal
ET041Gearbox ratio
ET047Fuel pump control circuit
ET051Throttle stop programming
ET089Flywheel target programming
ET148OBD warning light activation request
ET321Air conditioning compressor
ET405Clutch pedal switch
ET434Low fuel level
ET571LPG minimum signal
ET673Jammed accelerator pedal detected
ET717Target gearbox ratio
ET734Heating resistor 1 relay control
ET735Heating resistor 2 relay control
ET736Heating resistor 3 relay control
ET759Braking multiplex signal detected
ET760First starting
ET775Camshaft TDC* synchronisation
ET798Clutch wire contact connection
ET799Brake wire contact
PETROL INJECTION
Fault finding – Status summary table
17B-170V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET321AIR CONDITIONING COMPRESSOR
STATUS DEFINITIONACTIVE: This status indicates that the air conditioning compressor is active.
INACTIVE: This status indicates that the air conditioning compressor is inactive
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVETo check the operation of the air conditioning, run command AC180 Air
conditioning compressor relay control. In the event of a fault, apply the
interpretation of DF1072 Air conditioning compressor control.
V42_V04_ET321/V42_V05_ET321/V42_V06_ET321/V42_V14_ET321/V42_V16_ET321/V42_V18_ET321
17B-185V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR037REFRIGERANT PRESSURE
PA R A M E T E R
DEFINITIONThis parameter indicates the refrigerant pressure in bar.
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
The refrigerant pressure must be between 2 bar < PR037 < 27 bar.
Check the cleanliness and condition of the refrigerant pressure sensor and its connections, component code
1202 and the injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Using the universal bornier in place of the computer, check for insulation and continuity on the following
connections:
–38Y between components 120 and 1202,
–38X between components 120 and 1202,
–38U between components 120 and 1202.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the refrigerant pressure sensor, component code 1202 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
(See MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air
conditioning: Precautions for repair) and (see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), Mechanical, Air conditioning: Parts and consumables for the repair).
If the fault is present, check the air conditioning circuit (see MR 388 (Logan and Sandero), MR 451 (Duster) or
MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air conditioning: Check).
V42_V04_PR037/V42_V05_PR037/V42_V06_PR037/V42_V14_PR037/V42_V16_PR037/V42_V18_PR037
17B-213V2 MR-376-X76-17B050$140.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*TDC: Top Dead Centre
**GMV: fan assemblyTool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used to clear the faults stored in the computer.
RZ003 Engine adaptivesThis command enables a long engine start time.
RZ031 Throttle stop programmingThis command is used to reset the necessary system adaptives
if replacing the throttle valve.
RZ033Richness regulation
programmingThis command is used to reset the necessary system adaptives
if replacing the injectors.
RZ037Flywheel target
programmingThis command is used to reset the necessary system adaptives
if replacing the TDC* sensor.
RZ064Programming the level of
alcoholThis command is used to count the richness adaptive
programming necessary when replacing the injection computer.
AC005 Cylinder 1 injectorThis command is used to perform an audible check on injector 1.
AC006 Cylinder 2 injectorThis command is used to perform an audible check on injector 2.
AC007 Cylinder 3 injectorThis command is used to perform an audible check on injector 3.
AC008 Cylinder 4 injectorThis command is used to perform an audible check on injector 4.
AC015 Fuel pump relayThis command is used to check the fuel pump.
AC017Canister bleed solenoid
valveThis command is used to check the canister bleed solenoid
valve.
AC027 Motorised throttleThis command is used to check the motorised throttle.
AC038 Low speed GMV** relayThis command is used to check the low speed GMV** relay.
AC039 High speed GMV** relayThis command is used to check the high speed GMV** relay.
AC180Air conditioning
compressor relay controlThis command is used to check the air conditioning compressor
relay.
PETROL INJECTION
Fault finding – Command summary table
