2013 RENAULT KANGOO Passenger Comparment Connection Unit Workshop Manual

87B-17V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: WIPING (CONTINUED)
SUB-FUNCTION: WIPER CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Wiping - Washing
signalsET555:Rear screen
wiper signalPresent when the rear
screen wiper is working.In the event of a fault,
apply the interpretation of
status ET555 (see 85A,
Wiping - Washing).
ET492:Windscreen
washer signalPresent when the
windscreen washer is
working.In the event of a fault,
apply the interpretation of
status ET492 (see 85A,
Wiping - Washing).
ET557:Rear screen
washer signalPresent when the rear
screen washer is working.In the event of a fault,
apply the interpretation of
status ET557 (see 85A,
Wiping - Washing).
Supply PR001: Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).

87B-18V1 MR-376-X76-87B000$090.mif
87B
UCH
VDiag No.: 0F
Tool status Diagnostic tool name
ET004+ 12 V after ignition feed
ET008UCH blank
ET091Engine running
ET127Immobiliser warning light
ET489Front doors
ET549Immobiliser active
ET551Rear doors or boot
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Status summary table

87B-19
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
87B
UCH
VDiag No.: 0F
ET004+ 12 VOLTS AFTER IGNITION
NOTESSpecial note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
ET004: "NO" with the ignition on
Check fuse F15 (20 A) in the passenger compartment fuse and relay box, component code 260 (see MR 374,
Mechanical, 81C, Fuses, Fuses: List and location of components).
Using a multimeter, check for + 12 V after ignition on connection AP7 of the UCH connector, component code 645.
Using a multimeter, check for + 12 V on connection BP10 of the UCH connector, component code 645.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If there is no voltage, check the continuity and the insulation to earth on the following connection:
●AP7 between components 645 and 260.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
ET004: "YES" with the ignition off
Using a multimeter, check that there is no +12 V with the ignition off on connection AP7 of the UCH connector,
component code 645.
If the fault is still present, contact the techline.
UCH_V0F_ET004
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses

87B-20
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET127IMMOBILISER WARNING LIGHT
NOTESThe immobiliser warning light status should be OFF after the + after ignition feed is
switched on.
The immobiliser warning light status should be ON when the key is not in the ignition
switch.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the instrument panel connector, component code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using a multimeter, check the continuity and insulation of the following connection:
●87H between components 645 and 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ET127

87B-21
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET489FRONT DOORS
NOTESCheck that no fault is present.
Open the front doors one after another.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that, for each front door open, status ET489 is OPEN or for each front door closed, the status is CLOSED.
Check the connection and wiring of the driver's door rabbet switch, component code 180 and the passenger's door
rabbet switch, component code 181.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13A between components 180 and 645,
●13N or 13A between components 181 and 645,
●MK between component 180 and earth,
●MF between component 181 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the door rabbet switches.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET489

87B-22
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET549ENGINE IMMOBILISER ACTIVE
NOTESThe immobiliser active status should change to inactive when the + after ignition is
switched on.
The immobiliser status should be active when the key is absent from the ignition switch.
ET549: YES despite the presence of a key in the ignition switch and + after ignition feed
Check that there is no fault before dealing with this status.
Check that status ET004 + 12 V After ignition is YES with the ignition on.
Deal with status ET004 if it is NOwith the ignition on.
Check status ET185 Key code received and status ET184 Key code valid with the ignition on.
If statuses ET185 and ET184 are YES, perform fault finding on the injection computer.
If status ET185 is NO, deal with this status first.
If status ET185 is YES and status ET184 is NO, deal with status ET184 first.
If the fault is still present, contact the techline.
UCH_V0F_ET549

87B-23
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET551REAR DOORS OR LUGGAGE COMPARTMENT
NOTESCheck that no fault is present.
Open the rear doors one after another, then open the luggage compartment.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that when one of the rear doors or the tailgate is opened, status ET551 is OPEN and that when the rear
doors or tailgate are closed, status ET551 is CLOSED.
Check the connection and wiring of the rabbet switch on the rear right-hand door, component code 178, the rabbet
switch on the rear left-hand door, component code 179 and of the tailgate opening switch, component code 560.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13N or 13A between components 179 and 645,
●13N or 13A between components 178 and 645,
●MG between component 179 and the earth,
●MF between component 178 and earth,
●MG between component 560 and earth,
●13N or 13A between components 560 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the rabbet switches for the doors and the tailgate.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET551

87B-24V1 MR-376-X76-87B000$110.mif
87B
UCH
VDiag No.: 0F
Tool parameter Diagnostic tool name
PR001Battery voltage
PR008Vehicle speed
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Parameter summary table