2013 RENAULT KANGOO air condition

13B-25
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF001
PRESENT
OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT
CO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
NOTESSpecial notes:
If fault DF001 is present, the preheating time is greater than 10 seconds and the
engine fan switches on at low speed (Fan assembly 1). If there is a fault on Fan
assembly 1, then Fan assembly 2 switches on (on vehicles fitted with air conditioning).
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition and connection of the coolant temperature sensor connector, component code 244.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connectors, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3C between components 244 and 120,
●3JK between components 244 and 120,
●M (or NH) of component 244,
●42A between components 244 and 247.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the coolant temperature sensor between connections 3JK and 3C of component 244.
11.5 k < X < 13,5 k at -10°C,
2140  < X < 2364  at 25°C,
773  < X < 851  at 50°C,
275  < X < 291  at 80°C,
112  < X < 118  at 110°C.
If the value is not correct, replace the coolant temperature sensor (see MR 388 (Logan/Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 19A Cooling, Coolant
temperature sensor: Removal – Refitting).
DCM1.2_V08_DF001
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-26
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF002
PRESENT
OR
STOREDAIR TEMPERATURE SENSOR CIRCUIT
CO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
1.DEF: Inconsistency
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the connector of the air flow sensor, component code 799.
Check the condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connectors, otherwise
replace the wiring.
Check for + 12 V after ignition on connection 3FB (or 3FBA) of the air flow sensor connector.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the earth on connection NH of the air flow sensor.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
DCM1.2_V08_DF002

13B-28
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF003
PRESENT
OR
STOREDATMOSPHERIC PRESSURE SENSOR CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
NOTESSpecial notes:
The atmospheric pressure sensor is built into the injection computer.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Look for any wiring harness damage and check the condition and connection of the injection computer connectors,
component code 120.
Check the connection and condition of the injection locking relay connector.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Move the wiring harness between the injection computer and the battery, component code 107 to see if a change
of status occurs (Present  Stored).
Look for any damage to the wiring and check the connection and condition of the battery and its connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A (Renault) or Technical Note
9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace
the wiring.
Measure the battery voltage when the ignition is switched on.
If the battery voltage is less than 11 V, recharge the battery (see Technical Note 6014A (Renault) or Technical
Note 9859A (Dacia), Checking the charging circuit).
Check the condition and connection of the battery terminals and posts.
DCM1.2_V08_DF003

13B-29
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF005
PRESENT
OR
STOREDENGINE SPEED SENSOR CIRCUIT1.DEF: Inconsistency
2.DEF: Inconsistency
3.DEF: Too many additional teeth
4.DEF: Teeth missing
5.DEF: Additional teeth
6.DEF: Too many teeth missing
NOTESSpecial notes:
If fault DF005, 1.DEF, 2.DEF, 3.DEF or 6.DEF is present: the engine stops and the
level 2 warning light comes on.
If fault DF005, 4.DEF or 5.DEF is present: engine performance is reduced to 75%, and
no warning light comes on.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present when the starter motor is operating or the engine is running at idle
speed.
Check the connection and condition of the engine speed sensor connector, component code 149.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check that the engine speed sensor is correctly fitted to the engine.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3BL between components 120 and 149,
●3BG between components 120 and 149.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the engine speed sensor between connections 3BG and 3BL of component 149.
If the resistance of the engine speed sensor is not between 510  < X < 850  at 20°C, replace the sensor (see
MR 388 (Logan/Sandero) or MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 13B Diesel injection, Crankshaft position sensor: Removal – Refitting).
Check that the flywheel ring gear is not defective (missing teeth).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF005

13B-30
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF007
PRESENT
OR
STOREDRAIL PRESSURE SENSOR CIRCUITCC.0: Short circuit to earth
CO.1: Open circuit or short circuit to +12 V
1.DEF: Inconsistency
2.DEF: Below minimum threshold
3.DEF: Above maximum threshold
4.DEF: Value outside permitted tolerance
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine starts.
Special notes:
If fault DF007 is present, the engine stops and restarting is impossible.
Level 2 warning light comes on.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the rail pressure sensor connector, component code 1032.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 5 V on connection 3LX of the rail pressure sensor, component code 1032.
Check for earth on connection 3LZ of the rail pressure sensor, component code 1032.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3LX between components 120 and 1032,
●3LY between components 120 and 1032,
●3LZ between components 120 and 1032.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, the rail pressure sensor is faulty, replace the rail (see MR 388 (Logan/Sandero) or MR
451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection,
Injector rail: Removal – Refitting).
DCM1.2_V08_DF007

13B-32
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF008
CONTINUED 1
CO.0
CC.1
2.DEF
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3LR between components 120 and 921,
●3LS between components 120 and 921,
●3LT between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for + 5 V on connection 3LR of the pedal potentiometer, component code 921.
Check for earth on connection 3LT of the pedal potentiometer, component code 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the injection computer connector and the pedal potentiometer connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3LS between components 120 and 921,
●3LW between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.

13B-34
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF009
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
NOTESPriority when dealing with a number of faults:
– DF122 Pedal potentiometer gang 2 supply voltage.
Special notes:
If fault DF009 is present: engine speed maintained above 1000 rpm and engine
performance reduced to 75%, the level 1 warning light comes on.
If faults DF009 and DF008 Pedal potentiometer circuit gang 1 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CO.0
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 5 V on connection 3LU of the pedal potentiometer, component code 921.
Check for earth on connection 3LV of the pedal potentiometer, component code 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the computer connector and the connector of the pedal potentiometer, component code 921.
Check the insulation to earth of connection 3LW on the injection computer connector.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
DCM1.2_V08_DF009

13B-35
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF009
CONTINUED 1
Check the continuity of the following connection:
●3LW between components 120 and 921.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Measure the resistance between connections 3LV and 3LU of the pedal potentiometer, component code 921.
If the resistance is not between 1020  < X < 2380 , replace the pedal potentiometer (see MR 388 (Logan/
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Accelerator pedal: Removal – Refitting).
If the fault is still present, contact the Techline.
CC.1
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3LU between components 120 and 921,
●3LV between components 120 and 921,
●3LW between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.