2013 Peugeot 3008 Hybrid 4 display

24
FA
M
DRIVING SAFELY

S
peed limiter "LIMIT"



1.
Limiter mode Selection / Off.

2.
Decreasing the programmed value.

3.
Increasing the programmed value.

4.
Speed limiter On / Off.
154
Cruise control "CRUISE"



1.
Cruise control mode Selection / Off.

2.
Programming a speed / Decreasing
the programmed value.

3.
Programming a speed / Increasing
the programmed value.

4.
Cruise control Off / Resume.

In order to be programmed or
activated, the vehicle speed
must be higher than 25 mph
(40 km/h) and at least second gear
engaged.
156


Display in the instrument panel

The cruise control or speed limiter mode
appears in the instrument panel when it
is selected.

Cruise control

Speed limiter

HY
B
35
VIEW HYBRID FLOW INFORMATION
H
ybrid modes

1.
Hybrid mode selected (AUTO, ZEV, SPORT, 4WD).

2.
Messages, e.g.: "Zero Emission" if the Diesel engine is
off (0 g/km CO
2).


Operation / Energy flows


6.
The Diesel engine supplies the battery (if needed).

7.
Arrow from left to right: the battery powers the electric
motor (when the electric motor is operating).
Arrow from right to left: the electric motor/generator
recharges the battery (energy recovery phases).

8.
The Diesel engine drives the front wheels.

9.
The electric motor drives the rear wheels.
Vehicle infrastructure


3.
Diesel engine.

4.
Traction battery state of charge.

5.
Electric Motor/Generator. Information on the active hybrid mode, arrows for energy fl ows and the state of charge of the battery, is displayed in the in-
strument panel screen or the screen.

HY
B
36

Examples of displays


On starting and when stationary
There is no fl ow of energy (the Stop & Start system
stops and restarts the Diesel engine automatically).

Energy recovery
During this phase (deceleration, braking, foot off the
accelerator, … all modes), the battery is recharged by
the electric motor/generator, then being driven by the
rear wheels.
You can maximise this energy recovery by taking your
foot off the accelerator pedal, deceleration will then be
less marked than with a conventional vehicle.

100% electric
In all electric running (AUTO or ZEV modes), only the
electric motor, powered by the battery, drives the rear
wheels.
The display of "Zero Emission" indicates that the Diesel
engine is off and the vehicle is producing no CO
2.

41
CONSUMPTION OF YOUR HYBRID IN THE SCREEN

Average consumption over the last 5 minutes.
"60 % Hybrid Use" corresponds to 60 % of the
running time driven by the hybrid system and
40 % of the time with the Diesel engine only
(with no contribution from the hybrid system).

For more information on the trip com-
puter, refer to the corresponding sec-
tion. With the hybrid system active, when trip
2 displayed, press the control for 2 sec-
onds to reset the history to zero.
Resetting the history

HY
B
42
200 V HIGH VOLTAGE BATTERY

The 200 V high voltage battery cannot
be recharged from a mains supply.
The battery is Ni-MH (Nickel Metal Hy-
dride) and is located below the boot
fl oor, close to the electric motor.
Charging
The charging takes place automati-
cally when driving
.
The energy recovery can be faster dur-
ing deceleration.
The average state of charge is 4 to
5 bars, so preserving a margin for en-
ergy recovery when deceleration of go-
ing downhill (free energy).

The battery is charged when the vehi-
cle decelerates, the electric motor then
becomes a generator and converts ki-
netic energy into electrical energy (ex-
cept if the speed of the vehicle is above
70 mph (120 km/h)).
The battery is not recharged from a
mains supply.
The battery may also be charged auto-
matically when required by the Stop &
Start system of the Diesel engine.


To preserve the service life of
the battery, the level of charge
never falls below 20 %, even
if a level of 0 bars is displayed
after ZEV running.
Where the battery is close to maxi-
mum, vehicle deceleration with your
foot off the accelerator pedal will be
at a lower level.

This recovery allows the use of "free"
energy.
The battery charging time is very short
and is continuous.
A discharged battery (following ZEV
running or high load, for example) will
quickly return to a state of charge suf-
fi cient for full operation of the different
hybrid modes.

47
IN
S
Panel grouping together the vehicle operation indication dials and warning lamps.
INSTRUMENT PANELS


For more information, refer to
the corresponding section on
the button or function and its
associated display.
Dials

6.

Display zero reset or service indicator
re-display button.
Resets the selected function to zero
(trip distance recorder or service indi-
cator) or displays the service indicator
again.

7.
Instrument panel lighting dimmer.
Adjusts the brightness of the lighting
of the instruments and controls, if the
vehicle lighting is on.

8.
Ready lamp.

Indicates that the vehicle is ready to
move off.

1.
Power meter.

Indicates the power available as a
percentage .
For more information refer to the
"Hybrid" section.

2.
Coolant temperature gauge.


Indicates the temperature of the engine
coolant (degrees Celsius).

3.
Fuel gauge.

Indicates the quantity of fuel remaining
in the tank.

4.
Speedometer.

Indicates the current speed of the
moving vehicle (mph or km/h).

5.
Screen.

Screen(s)


A.
Speed limiter.

or
Cruise control.

(mph or km/h)

B.
Trip distance recorder.

(miles or km)

C.
Service indicator.

(miles or km) or,
Engine oil level indicator.

or
Distance recorder.

(miles or km)

D.
6-speed electronic gear control
gearbox.


E.
- Electrical fl ow or

- Warning messages and function
status messages
or

- Trip computer or

- Satellite navigation information or

-
Menus (with Peugeot Connect
Media Navigation (NG4 3D)).

48
IN
S
The main menu and its asso-
ciated functions can only be
accessed when stationary, via
buttons 1
to 4
.
A message appears on the screen,
above a certain speed threshold, in-
dicating that the main menu cannot
be displayed.
The trip computer displays can only
be accessed while driving, via but-
tons 2
and 3
(refer to the "Trip com-
puter" paragraph).



Main menu


)
Press button 1
for access to the
main menu and select one of the fol-
lowing functions:


- "Vehicle parameters",

- "Choice of language",

- "Choice of units".

)
Press button 2
or 3
to move in the
screen.

)
Press button 1
again to confi rm the
selection.

Instrument panel navigator associated
with the Peugeot Connect Media
This group of buttons permits:


- when stationary
, confi guration of the
vehicle's equipment and the screen
settings (languages, units...),

- while driving
, scrolling of the active
functions (trip computer, navigation...).
Controls
There are four buttons to control the large
16/9 screen in the instrument panel:


1.
access the main menu, confi rm the
selection,

2.
move up through the menu,

3.
move down through the menu,

4.
return to the previous display, exit
from the menu.

49
IN
S

Vehicle parameters
This menu allows you to activate or
deactivate certain driving and comfort
equipment (according to country):


- wiper linked with reverse gear (refer
to the "Visibility" section),

-
selective unlocking (refer to the "Access"
section),

- guide-me-home and welcome lighting
(refer to the "Visibility" section),

- interior mood lighting (refer to the
"Visibility" section),

- daytime running lamps (refer to the
"Visibility" section),

- directional headlamps (refer to the
"Visibility" section),

- automatic or manual parking brake
(refer to the "Driving" section).

Choice of units
This menu allows you to select the
units: temperature (°Celsius or °Fahr-
enheit) and fuel consumption (l/100 km,
mpg or km/l).

Choice of language
This menu allows you to select the display
language: Deutsch, English, Espanol,
Français, Italiano, Nederlands, Portugues,
Türkçe * .

*
According to country.
INDICATOR AND WARNING LAMPS


When the ignition is switched on
Certain warning lamps come on for a
few seconds when the vehicle's ignition
is switched on.
When the engine is started, these same
warning lamps should go off.
If they remain on, before moving off,
refer to the information on the warning
lamp concerned.

Associated warnings

The illumination of certain warning lamps
may be accompanied by an audible signal
and a message in the multifunction screen.
The warning lamps may come
on continuously (fi xed) or fl ash.
Certain warning lamps may
come on in one of two different
modes. Only by relating the type of
illumination to the operating status
of the vehicle can it be ascertained
whether the situation is normal or
whether a fault has occurred.


Visual indicators informing the driver
that a system is in operation (operation
or deactivation indicator lamps) or of the
occurrence of a fault (warning lamp).