2013 PEUGEOT 2008 ESP

128
i
Safety
Mud mode
Mode which, when moving off allowsconsiderable spin on the wheel with the leastgrip to optimise clearing of the mud and regain grip. At the same time, the wheel with the mostgrip is controlled in such a way as to pass as much torque as possible.
When moving, the system optimises wheel spin
to respond to the driver's requirements as
fullyas possible.
) Place the dial in this position.



Sand mode
Mode which allows little spin on the two drivingwheels at the same time to allow the vehicle tomove for ward and limit the risks of getting stuck
in the sand.
)Place the dial in this position.
D
o not use the other modes on sand as thevehicle may become stuck.


DSC OFF mode
)
Place the dial in this position.
This mode is active up to 30 mph
(50 km/h).

Driving advice
Your vehicle is designed principally to drive on tarmac roads but it allows you to drive on other less passable terrainoccasionally.
However, it does not permit all-terrain activities such as:


- crossing and driving on terrainwhich could damage the underbody
or strip away components (fuel pipe, fuel cooler, ...) due toobstacles or stones in particular,

- driving on terrain with steepgradients and poor grip,

- crossing a stream.

134
Safety
Lateral airbags
Deployment
The lateral airbags are deployed unilaterally in
the event of a serious side impact applied to all
or par t of the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The lateral airbag inflates between the hip andshoulder of the front occupant of the vehicle and the corresponding door trim panel.
System which protects the driver and frontpassenger in the event of a serious side impact
in order to limit the risk of injury to the chest,
between the hip and the shoulder.
Each lateral airbag is fitted in the seat backrest
frame, door side.

Impact detection zones
A.
Front impact zone.
B. Side impact zone.


Curtain airbags
System which protects the driver and
passengers (with the exception of the rear centre passenger) in the event of a serious side
impact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compar tment area.
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be
deployed.
In the event of a rear or front collision, the airbag is not deployed.


Deployment

The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or par t of the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or
rear occupant of the vehicle and the windows.
If this warnin
g lamp comes on in the instrument panel, accompanied by
an audible signal and a message in
the screen, contact a PEUGEOT dealer or aqualified workshop to have the system checked.
The airbags may no longer be deployed in the event of a serious impact.

Operating fault

156
Practical information
Fitting a wheel
Fitting the "space-saver"spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting, it is normal to notice that the washers
do not come into contact with the"space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checked by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repairedand refitted to the vehicle as soon as possible.


List of operations
)Put the wheel in place on the hub. )Screw in the bolts fully by hand.)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4 (if your vehicle has them). )Pre-tighten the other bolts using the
wheelbrace 1only.

164
Practical information
These bulbs are changed from inside the boot:
)open the boot, )remove the access grille from the corresponding side trim panel, )slacken and remove the nut, )disconnect the lamp unit connector, )remove the lamp unit carefully by it pullingin line towards the outside,
)
press the retaining tabs and remove the
bulb holder,
) turn the bulb a quar ter of a turn and change it.
To r e a s s e m b l e , c a r ry out these operations in reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.

167
7
Practical information
To replace a fuse, you must: )use the special tweezer to extract the fuse
from its housing and check the condition of
its filament.)always replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk of fire).
If the fuse fails again soon after replacement, have the vehicle's electrical system checked bya PEUGEOT dealer or a qualified workshop.


Changing a fuse

Before changing a fuse:
)the cause of the failure must be identified and rectified, )all electrical consumers must be switched
off,)the vehicle must be immobilised with the
ignition off,)identify the failed fuse using the tables and
layout drawings in the following pages.Good Failed
PEUGEOT will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and not
recommended by PEUGEOT andnot installed in accordance with itsinstructions, in par ticular when the combined consumption of all of the additional equipment connectedexceeds 10 milliamperes.


Installing electricalaccessories

Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on your vehicle, contact a PEUGEOT dealer or a qualified workshop.
The replacement of a fuse not shown in the tables below may cause a serious malfunction of your vehicle. Contact a PEUGEOT dealer or a qualified workshop.
Tweezer

171
7
Practical information
Fuse N°RatingFunctions
F1
615 A Front foglamps.
F18 10 A
Right hand main beam headlamp.
F1
910 A
Left hand main beam headlamp.
F25
30 A Headlamp wash relay (accessory).
F2
940 A Front wiper motor.
F3
080 A
Pre-heater plugs (Diesel).


Engine compartment fuses

The fusebox is placed in the engine compartment near the battery (left-hand side).


Access to the fuses
)Unclip the cover. )Change the fuse (see corresponding paragraph).)When you have finished, close the cover carefully to ensure correct sealing of the
fusebox.

Fuse table

174
Practical information
It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month.
The batteries contain harmful substancessuch as sulphuric acid and lead. Theymust be disposed of in accordancewith regulations and must not, in any circumstances, be discarded withhousehold waste. Ta k e used remote control batteries andvehicle batteries to a special collection point.
Protect your eyes and face beforehandling the battery.
All operations on the battery must be carried out in a well ventilated area andaway from naked flames and sources of sparks, so as to avoid the risk of explosion or fire.Do not try to charge a frozen battery;the battery must first be thawed out toavoid the risk of explosion. If the battery has been frozen, before charging haveit checked by a PEUGEOT dealer or a qualified workshop who will check thatthe internal components have not been damaged and the casing is not cracked, which could cause a leak of toxic andcorrosive acid.Do not reverse the polarity and use onlya 12 V charger.
Do not disconnect the terminals while the engine is running. Do not charge the batteries without disconnecting the terminals first. Wash your hands afterwards.
Do not push the vehicle to star t theengine if you have an electronic gearbox or automatic gearbox.







Before disconnecting the battery

Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors beforedisconnecting the battery.

Following reconnection
of the battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before star ting topermit initialisation of the electronic systems. However, if problems remain following this
operation, contact a PEUGEOT dealer or a qualified workshop.
Referring to the corresponding section, you must yourself reinitialise:


- the remote control key,

- the on-board satellite navigation system.

175
7
Practical information
System which manages the duration of use of certain functions to retain a sufficient level of charge in the battery.
After the engine has stopped, you can still use functions such as the audio and telematics
s
ystem, windscreen wipers, dipped beam headlamps, cour tesy lamps, etc. for a maximum combined duration of about thir ty minutes.








Electrical energy economy mode
Switching to economy mode
Once this time has elapsed, a message appears in the screen indicating that the vehiclehas switched to economy mode and the active
functions are put on standby.
If a telephone call is being made at this time, it
will be maintained for around 10 minutes with
the Bluetooth hands-free system of your audio
system.


Exiting economy mode

These functions are reactivated automatically
next time the vehicle is driven.) To restore these functions immediately,start the engine and let it run for at least five minutes.

A flat battery prevents the engine from starting (refer to the correspondingsection).









Load reduction mode

System which manages the use of cer tain
functions according to the level of charge
remaining in the battery.
When the vehicle is bein
g driven, the load
reduction function temporarily deactivates certain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated
automatically as soon as conditions permit.