2013 PEUGEOT 2008 boot

59
3
Comfort





Rear seats
)Move the corresponding front seat for ward
if necessary. )Check that the corresponding seat belt ispositioned correctly against the backrest and buckle it.)Place the head restraints in the lowposition.
) Straighten the seat backrest 2 and secure it. )
Check that the red indicator, located next to
the control 1, is no longer visible.) Unbuckle and reposition the seat belt on
the side of the backrest.
When repositioning the seat backrest,take care not to trap the seat belts.

)Press control 1
to release the seat backrest 2 .)
Fold the seat backrest 2 on to the cushion.


Folding the backrest
Repositioning the seat backrest

Bench seat with fixed one-piece cushion and split backrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot.

64
Comfort
In order for these systems to be fully effective, follow the operation and maintenance guidelines below: )To obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as wellas the air extractor located in the boot. )Do not cover the sunshine sensor, located on the dashboard; this is used for regulation of the digital air conditioning system. )Operate the air conditioning system for at least 5 to 10 minutes, once or twice a month to keep it in per fect working order. )Ensure that the passenger compar tment filter is in good condition and have the filter elements replaced regularly. We recommend the use of a combined passenger compar tment filter. Thanks to its special active additive, it contributes to the purification of the air breathed by the occupants and the cleanliness of the passenger compar tment (reduction of allergic symptoms, bad odours and greasy deposits).)To ensure correct operation of the air conditioning system, you are also advised to have it checked regularly as recommended in the ser vicing booklet.)If the system does not produce cold air, switch it off and contact a PEUGEOT dealer or a qualified workshop.
When towing the maximum load on a steep gradient in high temperatures, switching off theair conditioning increases the available engine power and so improves the towing ability.











Recommendations for ventilation and air conditioning


If after an extended stop in sunshine, the interior temperature is very high, firstventilate the passenger compar tment for
a few moments. Put the air flow control at a setting highenough to quickly change the air in the passenger compartment.

The air conditioning system does not contain chlorine and does not present any danger to the ozone layer.


The condensation created by the air conditioning results in a discharge of water under the vehicle which isperfectly normal.




Stop & Start
The heating and air conditioning systems only work when the engine is running. To maintaina comfor table temperature in the passenger compartment, you can temporarily deactivatethe Stop & Start system (see the corresponding section).

75
3
Comfort








Boot fi ttings
1.Luggage cover (see following page for details)2.Boot lamp
3.Retaining strap4.Stowing rings(depending on version)5.Retaining net

76
Comfort
This consists of two sections which can be folded back on each other.
To store it, fold it on itself and place it at the
bottom of the boot. To gain access to the boot
from the rear seats: )
raise the front section of the rear parcel shelf using the grip A
.

77
3
Comfort











Warning triangle (stowing)

Before leaving your vehicle to set up
and install the triangle, put on your high visibility vest.

The dimensions o
f the triangle (once folded) or
its storage box must be:


- A
: length = 438 mm,

- B: height = 56mm, -C: width = 38 mm.
To use the triangle, refer to the manufacturer'sinstructions.
Placing the triangle in the road


The location for stowing a folded triangle or its box is under the front seat or under the boot carpet (depending on version).
Distance from your vehicle (in metres)
Road
Motorway
DayNight
50 m 80 m15 0 m

These are the internationally recognisedvalues.
Use the triangle in line with local driving regulations.

The triangle is available as an accessory, contact a PEUGEOT dealer or a qualified
workshop.
) Place the triangle at a distance behindthe vehicle, as shown in the table below,
according to the type of road and the level
of ambient light.

117
5
Visibility
Rear wiper
If a significant accumulation of snow or ice is present, or when using a bicyclecarrier on the boot, deactivate theautomatic rear wiper via the vehicle configuration menu.

Rear wiper selection rin
g:
par
k,
intermittent wi
pe,
wash-wipe
(set duration).
Reverse gear
When reverse gear is engaged, the rear wiper will come into operation if the windscreen wipers are operating.
Programming

The function is activated or deactivated via the vehicleconfiguration menu.
This function is activated by default.

145
7
Practical information
This kit is installed in the storage box, under the boot floor.
Complete s
ystem consisting of a compressor
and a sealant car tridge which permits temporary repair of a tyre so that you can rdrive to the nearest garage.
It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.




















Temporary puncture repair kit

Access to the kit List of tools

All of these tools are specific to your vehicle and can vary according to equipment. Do not use them for other purposes.
1.12 V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also be used for adjusting tyre pressures.
2. Removable towing eye.See "Towing the vehicle".

151
7
Practical information














Changing a wheel

The tools are installed in the boot under the floor.
To gain access to them: )open the boot, )lift the floor and remove it. )remove the polystyrene spacer,)remove the carrier box containing the tools.


Access to the tools
List of tools *
3."Bolt cover" tool.
For removing the bolt protectors
(covers)on alloy wheels.4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special
"security" bolts.
5.Towing eye.
See "Towing the vehicle".

Procedure for chan
ging a faulty wheel for the spare wheel using the tools provided with the vehicle.
All o
f these tools are specific to your vehicle andcan vary according to the level of equipment. Donot use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removing
the wheel bolts.
2. Jack with integral handle.For raising the vehicle.

*
Depending on country of sale.