2013 PEUGEOT 2008 reset

1
21
Instruments and controls





LCD instrument panel
1.
Engine coolant temperature gauge. 2.Rev counter (x 1 000 rpm or tr/min),
graduation according to engine (petrol or
Diesel).3.Engine oil level indicator.4. Gear shift indicator for a manual gearbox
or gear lever position and gear for an electronic or automatic gearbox.
5. Digital speedometer (mph or km/h) This can be switched off with a long presson B.
A.General lighting dimmer.B.
Recall the service information.
Reset the function selected (service
indicator or trip distance recorder).
Setting the time.
Switching the digital speedometer on and off.
6.
Cruise control or speed limiter settings.7.
Ser vice indicator, then total distance recorder (miles or km).
These functions are displayed successively
on switching on the ignition.8. Trip distance recorder (miles or km).
9. Analogue speedometer (mph or km/h).
10.Fuel gauge.



Dials and screens
Control buttons

22
Instruments and controls
Active matrix instrument panel
Dials and screens
Control buttons
1.
Engine coolant temperature gauge. 2.
Rev counter (x 1 000 rpm or tr/min),
graduation according to engine (petrol or Diesel).3. Cruise control or speed limiter settings.4.
Gear shift indicator for a manual gearbox
or gear lever position and gear for an
electronic or automatic gearbox. 5. Speedometer (mph or km/h).
A.Main lighting dimmer. B.Instrument panel mood lighting.
C.Recall of the service information.
Reset the selected function (service
indicator or trip distance recorder).
6
. Service indicator, then total distance
recorder (miles or km).
These functions are displayed successively on switching on the ignition.
7.Trip distance recorder (miles or km).8. Analogue speedometer (mph or km/h).9.Fuel gauge.

1
35
Instruments and controls
Service indicator
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no ser vice information appears in the screen.
S
ystem which informs the driver when the next ser vice is due, in accordance with themanufacturer's servicing schedule.
The point at which the ser vice is due is calculated from the last indicator zero reset. It
is determined by two parameters:


- the distance travelled,

- the time elapsed since the last ser vice.
Between 600 miles (1 000 km)and 1 800 miles (3 000 km) remainbefore the next service is due
For 7 seconds after the ignition is switched on, the
spanner symbolising the ser vice operations comes
on. The distance recorder display line indicates the
distance remaining before the next ser vice is due.
Example:
1 700 miles (2 800 km) remain before the next service is due.
For 7 seconds after the ignition is switched on,
the screen indicates:
7 seconds a
fter the ignition is switched on,the spanner goes off; the distance recorder fresumes its normal operation. The screen thenindicates the total and trip distances.

Less than 600 miles (1 000 km) remain before the next service is due
Example:560 miles (900 km) remain before
the next service is due.
For 7 seconds after the i
gnition is switched on,
the screen indicates:
7 seconds after the i
gnition is switched on,
the distance recorder resumes its normal operation. The spanner remains on
toindicate that a service must be carried out soon.

36
Instruments and controls
Service overdue
For 7 seconds after the ignition is switched on, the
spanner flashesto indicate that the service must
be carried out as soon as possible.
Example: the ser vice is overdue by 18 6 miles(300 km).
For 7 seconds after the ignition is switched on, thescreen indicates:
The distance remaining may be weighted by the time factor, dependingon the driving conditions.
Therefore, the spanner may also comeon if you have exceeded the period since the last service, indicated in the servicing and warranty booklet.
Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account.
Service indicator zero reset

After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the trip distance recorder
zero reset button,
) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.

Retrieving the serviceinformation

You can access the ser vice information at any
time.
)Press the trip distance recorder zero reset button.
The ser vice information is displayed for a
few seconds, then disappears.
7 seconds after the i
gnition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on.

1
37
Instruments and controls
Engine oil level indicator
Oil level incorrect
This is indicated by the flashing of " OIL" or LLby the display of a dedicated message in theinstrument panel.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
avoid damage to the engine.

Oil level indicator fault

This is indicated by the flashing of "OIL_ _" or
by the display of a dedicated message in the
instrument panel. Contact a PEUGEOT dealer or a qualified workshop.


Dipstick

Refer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.
There are 2 marks on the dipstick: The total milea
ge is displayed in zone A
of the screen and the trip mileage in zone B.

With the trip mileage displayed, press the button for a few seconds.


Mileage recorder

Tr i
p recorder zero reset
System which informs the driver whether the
engine oil level is correct or not.
This information is indicated for a few seconds when the ignition is switched on, after the service information.
The level read will only be correct if
the vehicle is on level ground and theengine has been off for more than 30 minutes.


-
A= max; never exceed this
level,
-B= min; top up the level via
the oil filler cap, using the grade of oil suited to your engine.
Oil level correct

1
39
Instruments and controls

Tr ip reset
)When the trip required is displayed, press
the control for more than two secondsor use the left hand thumb wheel of the steering mounted controls.
Trips "1"
and "2"are independent but their useis identical.
For example, trip "1"
can be used for daily figures, and trip "2"
for monthly figures.

1
41
Instruments and controls

Tr ip reset
)
When the desired trip is
displayed, press the reset zone, located at bottom right of the
touch screen.
Trips
"1"
and "2"are independent but their use
is identical.
For example, trip "1"
can be used for daily
figures, and trip "2"
for monthly figures.

42
Instruments and controls
Stop & Start time counter
(minutes / seconds or hours /
minutes)

If dashes are displayed continuously while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).


This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
Trip computer, a few definitions

Range
(miles or km)
The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)
travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Current fuel consumption
(mpg or l/100 km or km/l) Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l) Calculated since the last trip computer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.


Distance travelled
(miles or km)
Calculated since the last trip
computer reset.

If
your vehicle is fitted with Stop & Star t, a timecounter calculates the time spent in STOP mode during a journey. It resets to zero every time the ignition isswitched on with the key.