2013 MITSUBISHI iMiEV charging

• Do not repeat charging near the full
charge level.
l The quick charging gives priority when the
regular charging and the quick charging are
performed at the same time.
At this time, the regular charging will be stop-
ped.
l The progress of the battery capacity loss de-
pends on the vehicle usage and the environ-
ment.
We recommend to do regular charging from
2 segments or less to charge completely at
least once in 3 months.
The procedure lets the battery remaining indi-
cator adjusted automatically.
l In the event of an electrical power outage
while charging, charging restarts automatical-
ly with the restoration of electricity.
EV charging cable* E08301100066
Your vehicle is equipped with the EV charging ca-
ble (A) with control box (B).
Indicator (LED)
(Green)
(Orange) (Red)
READY
CHARGE
FAULT The indicator illuminates/blinks in the following
conditions.
: Illuminates : Blinking : Not illuminates Charging
1-05 1
OHAE13E1

READY
(Green) CHARGE
(Orange) FAULT
(Red) Normal operating condition of the control box
Every time the charging cable plug (C) is connected to an outlet, all indication lamps illuminate for 0.5 seconds.
After initial processing is completed, when the regular charge connector is not connected to the vehicle, or the
regular charge connector is connected to the vehicle but charging is not being performed.
While the traction battery is being charged
READY
(Green) CHARGE
(Orange) FAULT
(Red) Abnormal operating condition of the control box and corrective action
When an electric leakage occurs or the EV charging cable malfunctions
Stop use immediately and contact a
MITSUBISHI MOTORS Authorized Service Point. When the EV charging cable malfunctions
Stop use immediately and contact a

MITSUBISHI MOTORS Authorized Service Point. If the control box indication lamp does not illuminate after connecting the charging cable plug to the outlet,
check the circuit breaker for the outlet. If the breaker has tripped, the circuit may not be suitable for use with
EV charging cable. You should have a licensed electrician inspect and repair the electrical circuit. If the break-
er is not tripped, stop using the EV charging cable and contact a

MITSUBISHI MOTORS Authorized Service
Point. WARNING
l If
the green or orange indicator does not
illuminate or the red indicator blinks or il-
luminates during regular charging,
please contact a MITSUBISHI MOTORS
Authorized Service Point.
l Do not charge with the EV charging ca-
ble banded or rolled.
The cable may be heated and resulting in
fire.
l Do not alter or disassemble the EV charg-
ing cable.
Doing so could cause fire, an electric
shock or injury. WARNING
l Be sure to install the cap to the regular
charge connector and store the EV charg-
ing cable at a place where the cable is not
exposed to water or dust. Entry of foreign
matter such as water or dust at the metal
terminal of the regular charge connector
or charging cable plug may cause a fire
or malfunction. Contact with metal such
as wire or tool may cause fire, an electric
shock or malfunction. WARNING
l Never force the connection if the EV charg-
ing cable or connector shows damage or
is not easily connected due to foreign ma-
terial entering the connector or the out-
let. And never use an outlet that is worn,
damaged, or will not hold the plug firmly.
Doing so could cause fire, an electric
shock, or short circuit.
l Pay attention to the following for han-
dling the EV charging cable.
Damage to the cable could cause fire, an
electric shock, or short circuit.
• Do not pull with undue force.
• Do not twist. Charging
1-06
1
OHAE13E1

WARNING
• Do not drag.
• Do not put an object on top.
• Do not put the cable close to a heating unit including heater.
• Do not drop the regular charge con- nector or do not give strong impact to
it. CAUTION
l
Do
not charge with the outlet that is small-
er than the current value described on
the control box.
NOTE l All

indicators are illuminated momentarily
for confirming operation when the charging
cable plug is inserted into an outlet. After
that the green indicator is continuously illu-
minated.
l The orange indicator will go off when the
charging is completed. The green indicator is
continuously illuminated while the charging
plug is inserted into an outlet. Handling and storing the control box
E08301200025 CAUTION
l
While
charging, it must be prevented be-
ing damaged to the control box by the at-
tached rope as shown in the following il-
lustration.
NOTE l Use

the hook with load capacity over 4 kg,
that weight is the EV charging cable.
l Check the rope has no damage or no loose be-
fore use.
Hook
Rope Cleaning the EV charging cable
E08301300042
1. Gently
wipe off with gauze or other soft
cloth soaked with a 3 % aqueous solution of
neutral detergent.
2. Wipe off all the detergent with a soft cloth dipped in fresh water and thoroughly wrung
out. 3. Wipe
all moisture off and dry in a shaded,
well-ventilated area. WARNING
l In
cleaning, be sure to remove the charg-
ing cable plug and the regular charge con-
nector from the outlet. Do not connect or
disconnect the plug and the connector
with wet hands. Doing so could cause an
electric shock.
l Do not have the metal terminal of the reg-
ular charge connector and the charging
cable plug be exposed to water or neutral
detergent. Operation with water could
cause fire or an electric shock. CAUTION
l
Never use benzine, petrol, or other organ-
ic

solvents, or acid or alkaline solvents. Do-
ing so could cause deformation, discol-
our, or malfunction. Also, these substan-
ces may be present in various cleaners, so
check carefully before use. Charging
1-07 1
OHAE13E1

Regular charging (charging
method with rated AC 220-240 V outlet) E08300900054WARNING
l For safety, do not allow children or peo-
ple who are not familiar with charging to
charge for themselves. Also, do not use
the charge connector within reach of chil-
dren.
l Persons who use electro-medical appara-
tus such as implantable cardiac pacemak-
er or implantable cardioverter defibrilla-
tor must check effect from charging with
the manufacturer of electro-medical appa-
ratus.
l If you use any medical electric devices,
take into account the following precau-
tions.
• Do not stay inside the vehicle.
• Do not go inside the vehicle, for exam-ple to remove or place an item in the
passenger compartment.
• Do not open the rear hatch, for exam- ple to remove or place an item in the
cargo area.
Charging may affect the operation of elec-
tric medical devices and result in serious
personal injury or death.
l Do not charge with the EV charging ca-
ble banded or rolled.
Doing so the cable may be heated and this
might result in fire. WARNING
l Before
charging, make sure that there is
no foreign matter such as dust at the reg-
ular charge port and the regular charge
connector.
At this time, do not touch the regular
charge port.
l When the regular charge connector is con-
nected to the charge port, prevent foreign
matter such as water or dust from enter-
ing in the port.
Connection with foreign matter such as
water or dust may cause fire or an elec-
tric shock. Do not perform charging if
there might be strong exposure to water
at the connection.
l Never pull the cable to remove the plug.
And never submerge the EV charging con-
nector, control box or plug in water.
l Please observe the following in order to
prevent accidents during charging such
as electrocution.
• Always use a charging cable that suit-able for this vehicle.
• Do not charge another vehicle using the attached EV charging cable.
Doing so the cable may be heated and
this might result in fire.
• Make sure to use an outlet that is pro- tected from water entering.
• Do not perform charging with the body cover.
• Do not remove and insert the plug and connector with wet hands.
• Do not charge the battery if there is a risk of lightning. WARNING
l While it is normal for the connector and
charging cable to become warm during
charging, discontinue use immediately if
the connector or charging cable becomes
hot to the touch.
l While it is normal for the control box to
become warm during charging, discontin-
ue use immediately if the control box be-
comes hot to the touch.
l If abnormal smells are detected or the ve-
hicle produces smoke, quickly stop charg-
ing.
l Do not perform charging at a poorly ven-
tilated place with surroundings covered.
Keep sparks, cigarettes, and flames away
from the auxiliary battery.
Flammable gas generated from the auxili-
ary battery in charging may be filled in a
building, resulting in explosion.
If charging is inevitably required, venti-
late the area well.
l Grasp the regular charge connector when
connecting or disconnecting the EV charg-
ing cable.
Grasping the cable could cause an elec-
tric shock, short circuit, and/or fire.
l During charging, the cooling fans inside
the bonnet room may automatically be op-
erated even if the electric motor switch is
in the “LOCK” position.
Keep your hands away from the cooling
fan during charging. Charging
1-08
1
OHAE13E1

CAUTION
l
Do not perform charging from other pow-
er source like a generator. Doing so could
cause a malfunction.
NOTE l If

the charge connector is not easily connec-
ted to the charge port due to foreign material
entering, never force the connection. Doing
so could damage the charging equipment or
the vehicle. Contact a MITSUBISHI
MOTORS Authorized Service Point.
l The on board charger is only for rated AC
220-240 V outlets.
l When connecting or disconnecting the regu-
lar charge connector, insert/pull out the con-
nector straight.
Also, do not incline or twist the connector.
Doing so could cause a bad connection or mal-
function.
l Make sure to lock the doors to prevent theft,
etc. during charging.
Charging from rated AC 220-240 V
outlet E08301000065
1. Fully
apply the parking brake and place the
selector lever to the “P” (PARK) position.
2. Stop the electric devices such as lamps and turn the electric motor switch to the “LOCK”
position. 3. Pull
the regular charging lid opener (A) at
the bottom left/right of the instrument panel
to open the regular charging lid (B) at the
right rear side of the vehicle. 4. Press the tab (C) to open the inner lid (D). WARNING
l Do
not touch the metal terminal of the reg-
ular charge port (E) and the regular
charge connector.
Doing so could cause an electric shock and/
or malfunction. CAUTION
l
Do
not leave for a long time with the in-
ner lid opened. It becomes impossible to
charge if a foreign material is entered to
the regular charge port.
NOTE l There

is a hole on the charge port for water
drainage. If this hole is blocked and water
gets trapped in the charge port, do not
charge. Contact a MITSUBISHI MOTORS
Authorized Service Point.
l If the charge port is frozen, melt the ice us-
ing a hair drier. Forcing the charge connector
to connect while frozen could result in mal-
function.
5. Insert the charging cable plug into an outlet.
NOTE l The shape of the charging cable plug and out-
let may differ from country to country as
shown in the illustration.
l Use the following outlets. Charging
1-09 1
OHAE13E1

WARNING
l Make sure that the plug is inserted all the
way into the outlet before use.
l To reduce the risk of electric shock or
fire due to electric leak, always use an out-
let protected by a residual current detec-
tor, rated for amperage equal to or great-
er than the value specified by
MITSUBISHI MOTORS, and that is con-
nected to a dedicated branch circuit. If
the circuit is shared, and another electri-
cal device is being used at the same time
the vehicle is charging, the breaker may
trip and the circuit may cause adverse in-
terference on MCB (Moulded Circuit
Board) and household electrical applian-
ces such as TVs and audio systems.
l To reduce the risk of electric shock, con-
nect only to a properly earthed and water-
proofed outlet.
Switzerland 250 V/10 A
Italy 250 V/10 A
Denmark 250 V/13 A
UK, Ireland 250 V/13 A
Germany, Spain, France, Sweden, etc. 250 V/16 A
Industrial plug for Europe 250 V/16 A 6. Remove the cap (F) on the regular charge con-
nector (G) and make sure that there is no for-
eign matter such as dust at the end of the reg-
ular charge connector and the regular charge
port. 7. Connect
the regular charge connector until a
click sound is heard without pressing the but-
ton (H). Charging
1-10
1
OHAE13E1

CAUTION
l
Do not clasp the top of regular charge con-
nector. It could cause injury to touch the
protrusion on the lid. NOTE
l If

the electric motor switch is turned to the
“START” position with the regular charge
connector connected to the regular charge
port, the electric motor unit cannot be started.
8. Make sure that the charging indicator on the instrument cluster is illuminated. If the charging indicator is not illuminated,
charging is not started.
Make

sure that the regular charge port, the
plug and the connector are appropriately con-
nected, and perform charging from Step 5
again.
NOTE l When the regular charge connector is connec-
ted to the charge port, the charging indicator
is blinking. When charging is started, the
charging indicator is illuminated.
l The charge level for traction battery can be
checked with the energy level gauge (I) on
the instrument cluster.
Refer to “Energy level gauge” on page 4-06. 9. Charging
is complete when the charging indi-
cator turns off. Pull out the regular charge con-
nector while pressing the button (J). NOTE
l Charging

can be stopped half way. In this
case, also, pull out the regular charge connec-
tor while pressing the button.
10. Close the inner lid and close the regular charg- ing lid. Charging
1-11 1
OHAE13E1

NOTE
l Make
sure that the inner lid is completely
closed.
If the regular charging lid is forcibly closed
without completely closing the inner lid, the
hinge on the inner lid may be broken.
11. Remove the charging cable plug from the out- let.
12. Install the cap on the regular charge connector. WARNING
l After
charging, be sure to close the inner
lid and the regular charging lid complete-
ly.
Be careful that water or dust does not en-
ter in the regular charge port, inner lid
and regular charge connector.
Entry of water or dust could cause elec-
tric leakage, resulting in fire or electric
shock.
l After charging, be sure to disconnect the
charge connector from the charge port.
If the charge connector is only partially
engaged and the connector latch is un-
locked, you could turn the electric motor
switch to the “START” position and the
vehicle could start moving. It could lead
to an unexpected accident. CAUTION
l
After
charging, be sure to disconnect the
plug from the outlet.
If the plug is left connected to the outlet,
immersion in water or tampering may
cause leakage or an electric shock. Quick charging (charging
method with quick charger) E08301400069 WARNING
l Be
sure to use the quick charger compati-
ble with i-MiEV.
Use of a non-compatible quick charger
may cause fire or malfunction.
For the quick charger compatible with
i-MiEV, consult a MITSUBISHI
MOTORS Authorized Service Point.
l For operation of quick chargers, follow
the manual of each quick charger.
l Persons who use electro-medical appara-
tus such as implantable cardiac pacemak-
er or implantable cardioverter defibrilla-
tor must check effect from charging with
the manufacturer of electro-medical appa-
ratus. Electro-medical apparatus opera-
tions could be affected by charging.
l Before charging, make sure that there is
no foreign matter such as dust at the
quick charge port and the quick charge
connector.
At this time, do not touch the quick
charge port. Charging
1-12
1
OHAE13E1