2013 MERCEDES-BENZ SPRINTER jacking points

J
Jack Jacking points ................................ 304
Preparation .................................... 304
Storage location ............................ 264
Using ............................................. 304
Jump-starting ..................................... 267K
Key Position in the ignition lock ............ 133
see SmartKey
Kickdown ........................................... 140L
Lamps see Warning and indicator lamps
Language
Display (vehicles with steering
wheel buttons) ............................... 185
Lashing points and tie downs
Permissible tensile loa d................. 327
LATCH-type (ISOFIX) child seat
anchors ................................................ 52
License plate lamp Changing bulbs ......................100, 101
License plate lamp (Chassi sCab)
Changing bulbs .............................. 100
Lighting
see Lights
Lights
Activating/deactivating daytime
running lamp mode (vehicle swith
steerin gwheel buttons) ................... 91
Activating/deactivating surround
lighting (vehicles with steering
wheel buttons) ............................... 187
Automatic headlamp mode ..............91
Bulb failure indicator ........................90
Cornering light function ...................93
Driving abroad ............................... 149
Fog lamps ........................................ 91
Hazard warning lamps .....................93
Headlamp range .............................. 93
High bea mflasher ............................ 92
High-beam headlamps .....................92Important safety notes
....................90
Ligh tswitc h..................................... 90
Low-beam headlamps ......................90
Parking lamps .................................. 90
Rea rfog lamp .................................. 91
Setting the exterio rlighting
delayed switch-off (vehicles with
steerin gwheel buttons) .................188
Switching the daytime running
lamp mode on/off (switch) ..............91
Turn signals ..................................... 92
see Changing a bulb
see Interior lighting
Light sensor ......................................... 91
Limited Warranty ................................ 29
Load distribution ............................... 234
Loading guidelines Important safety notes ..................232
Loading rails
Installing cargo tie-down rings .......236
Maximum tensile strength .............327
Loads
Securing ........................................ 234
Transporting .................................. 232
Load securing aids
Carrier systems ............................. 236
Locator lighting
Setting (vehicles with steering
wheel buttons) ............................... 187
Locking
see Centra llocking
Locking and unlocking manually .......69
Locking centrally see Centra llocking
Low-beam headlamps
Changing bulbs ................................ 98
Daytime running lamp mode
(vehicles without steering wheel
buttons) ......................................... 179
Daytime running lamp mode
(vehicles with steering wheel
buttons) ......................................... 187
Display message ............................ 201
Driving abroad ............................... 149
Switching on/off .............................. 90
Lumbar support ................................... 8012
Index

X
Take the vehicle tool kit and the jack from
the footwell on the co-driver's side
(Y page 264).
X Remove the spare wheel from the spare
wheel bracket (Y page 309). Observe the
safety notes in the "Spare wheel" section
(Y page 308).
X On wheels with wheel bolts, remove the
hub caps. X
Assemble the lug wrench extension using
the middle rod and the rod with the largest
diameter from the three-piece jack pump
lever.
X Starting with the middle rod, slide the lug
wrench extension as far as it will go onto
the lug wrench.
X Using lug wrench 0005, loosen the wheel
bolts/wheel nuts on the wheel to be
changed by about one full turn. Do not
unscrew the wheel bolts/nuts completely.
Raising the vehicle G
WARNING
If you do not position the jack correctly at the
appropriate jacking point of the vehicle, the
jack could tip over with the vehicle raised.
There is a risk of injury.
Only position the jack at the appropriate
jacking point of the vehicle. The base of the
jack must be positioned vertically, directly
under the jacking point of the vehicle. G
WARNING
On uphill and downhill slopes, the jack could
tip over with the vehicle raised. There is a risk
of injury.
Do not change wheels on uphill or downhill
gradients. Notify a qualified specialist
workshop.
! Only position the jack on the jacking
points intended for this purpose. You could
otherwise damage the vehicle.
Observe the following when raising the
vehicle:
R When raising the vehicle, only use the jack
specifically approved for your vehicle.
R the vehicle's jack is intended only to raise
the vehicle for a short time when changing
a wheel. It is not suited for performing
maintenance work under the vehicle.
R avoid changing the wheel on uphill and
downhill slopes.
R before raising the vehicle, secure it from
rolling away by applying the parking brake
and inserting wheel chocks. Never
disengage the parking brake while the
vehicle is raised.
R the jack must be placed on a firm, flat and
non-slip surface. On a loose surface, a
large, load-bearing underlay must be used.
On a slippery surface, a non-slip underlay
must be used, e.g. rubber mats.
R make sure the distance between the
underside of the tires and the ground does
not exceed 1.2 inches (3 cm).
R never place your hands or feet under the
raised vehicle.
R never lie under the raised vehicle.
R never start the engine when the vehicle is
raised.
R never open or close a door when the vehicle
is raised.
R make sure that no persons are present in
the vehicle when the vehicle is raised. 304
Changing wheelsWheels and tires

!
Only use the jack pump lever middle rod
and the rod with the largest diameter as a
lug wrench extension. Only slide the middle
rod as far as it will go onto the lug wrench.
The rods may otherwise bend and be
distorted to such an extent that they can
no longer be used as a pump lever for the
jack.
! Do not place the jack on the leaf spring or
the differential case. Hydraulic jack
Preparing the hydraulic jack
X
Insert the third rod of jack pump lever 0005
into the lug wrench extension.
Jack pump lever 0005is assembled.
X Close pressure release screw 0006.
X To do this, use the flattened section on
pump lever 0005to turn pressure release
screw 0006clockwise to the stop.
i Do not turn pressure release screw 0006
more than 1 or 2 full turns. Hydraulic fluid
could otherwise escape.
X Insert pump lever 0005into the recess on the
jack and secure by turning it clockwise.
X Place the jack vertically beneath the
jacking points described below. Jacking point, front axle
Jacking point at the front axle
X
Place the jack under the longitudinal
member in front of the front axle. Jacking point, rear axle (example: vehicle type
2500)
Jacking point, rear axle (example: vehicle type
3500)
Jacking point at the rear axle on vehicle
types 2500 and 3500
X
Place the jack under the longitudinal
member in front of the rear axle. Changing wheels
305Wheels and tires Z