2013 MERCEDES-BENZ S-CLASS SEDAN navigation system

R
calling up the DVD menu and navigating
within it
R setting
the language, subtitles and camera
angle
R calling up interactive DVD content
The following functions affect only one
screen:
R audio and video functions as well as picture
settings
R switching between full screen and the
menu
Switching between operating modes
When you exit an operating mode (e.g. audio
CD mode), the current setting is saved. If you
call up this operating mode again later, there
are two possibilities:
R the operating mode has been changed on
the other screen.
R the operating mode has not been changed.
In the first case, the operating mode appears
as it is on the other screen.
In the second case, the setting appears on the
screen as it was when you last exited the
operating mode.
Picture settings Overview
You can select these settings in video DVD
and AUX mode. Instructions for AUX mode
are detailed later

(Y page 258).
Adjusting the brightness, contrast and
color
X Switch on video DVD mode ( Y page 241).
X To show the menu: press the 9 button
on the remote control.
or
X Select Menu while the navigation menu
(Y page 241) is shown and press the 9
button to confirm.
X In both cases, select Video DVD using
the :=; buttons and press the
9 button to confirm. X
Select Brightness, Contrast, Color or
Auto using the 9: buttons and
press 9 to confirm.
An adjustment scale appears.
X Select a setting using the 9:
buttons
and press the 9 button to confirm.
Changing the picture format
X To show the menu: press the 9 button
on the remote control.
or
X Select Menu while the navigation menu
(Y page 241) is shown and press the 9
button to confirm.
X Select Video DVD using
the :=; buttons and press the
9 button to confirm.
The ä symbol in front of the Auto, 16:9
Optimized, 4:3

or Widescreen menu item
indicates the format currently set.
X Select a format using the 9:
buttons

and press the 9 button to confirm. System settings
Note You can adjust almost all system settings
individually

for each screen without affecting
the other screen. You make these settings
using the remote control.
Selecting the display language X
Select System using the 9=;
buttons on the remote control and press
the 9 button to confirm.
You see the system menu on the selected
rear screen. Rear Seat Entertainment System
249
COMAND Z

Hiding/showing the navigation menu
X
To show: press the 9 or : button
on the remote control.
X To hide: press the 9 or : button.
or
X Wait for approximately eight seconds. Navigation menu
:
Data medium type
; Current track
= Current scene
? Track time
A To show the menu
Showing/hiding the menu X
To show: press the 9 button on the
remote control.
or
X Select Menu while the navigation menu is
shown and press the 9 button to confirm.
X To hide:
press the 9 button and confirm
Full Screen by pressing the 9 button. Menu system
:
Video DVD options
; Pause function
= Stop function
? To set the treble
A To set the bass
Fast forward/rewind X
Press and hold the E
or F button on
the remote control until the desired
position has been reached.
You see the navigation menu.
Pause function X
To show the menu: press the 9 button
on the remote control.
or
X Select Menu while the navigation menu is
shown
and press the 9 button to confirm.
X To pause playback:
select Ë and press
the 9 button to confirm.
The Ë display changes to Ì.
X To continue playback: select Ì and
press the 9 button to confirm.
The menu is hidden. Rear Seat Entertainment System
255
COMAND Z

Stop function
X
To show the menu: press the 9 button
on the remote control.
or
X Select Menu while the navigation menu is
shown and press the 9 button to confirm.
X To interrupt playback: select É and
press the 9 button to confirm.
The Ë display changes to Ì. The
video image is hidden.
X To continue playback: select Ì and
press the 9 button to confirm.
Playback

continues from the point where it
was interrupted. The menu is hidden.
X To stop playback: while playback is
interrupted, select É again and press
the 9 button to confirm.
Playback stops and returns to the
beginning of the DVD. Ì is highlighted.
X To restart playback: select Ì and
press the 9 button to confirm.
Playback starts from the beginning of the
DVD.
Selecting a scene/chapter Note
Further information on this function is
available in the "Video" section
(Y page 243).
Skipping forwards/backwards
X
Press the = or ; button on the
remote control.
or
X Press the E or F button.
The control menu appears for
approximately eight seconds.
Selecting a scene/chapter directly
The
examples illustrate how to select scene/
chapter 5. X
Option 1: while the film is playing, press
the h button on the remote control.
X Press a corresponding number key, e.g.
¿.
X Option 2: while the film is playing, press
the 9 button on the remote control and
show the menu.
X Select Video
DVD and press the 9 button
to confirm.
X Select DVD Functions and press the 9
button to confirm.
X Select Scene Selection and press 9 to
confirm.
X Press 9
or : to select number 5 and
press the 9 button to confirm.
In both cases, playback will begin from the
fifth scene/chapter after a brief pause.
Selecting a film/title Note
Further information on this function is
available in the "Video" section
(Y page 243).
Option 1
X
Press the 9 button on the remote control
and show the menu.
X Select Video
DVD and press the 9 button
on the remote control to confirm. 256
Rear Seat Entertainment System
COMAND

X
Select Setting by sliding ZVÆ or turning
cVd the COMAND controller and press
W to confirm.
The massage function runs for
approximately 6 to 20 minutes, depending
on the setting. Uploading/downloading data
With this function, you can transfer COMAND
data from one system (vehicle) to another
system (vehicle). You can use either a USB
stick or an SD card as temporary storage.
You can only transfer the complete
transferable data record.
The following data is included in the complete
transferable data record:
R navigation destination memory and last
destination
R address book entries
R audio station/video channel presets
R system settings Copying data to a storage medium
X
Insert an SD card into the SD card slot
or
X Insert a USB stick into the socket on the
side in the glove box.
X Select Vehicle
in the main function bar by
turning cVd the COMAND controller and
press W to confirm.
The "Vehicle" menu appears.
X Select System and press W to confirm. X
Select Upload/Download Data and press
W to confirm.
X Select Copy Data to Storage Medium
and press W to confirm.
X Select the storage medium to which the
data should be copied.
X Select Start Copying.
COMAND checks whether the storage
medium has enough storage capacity. If
there is enough storage capacity, the data
is copied to the storage medium.
X If there is not enough storage capacity,
remove the storage medium. Make more
storage space available on the storage
medium. Then, try to copy the COMAND
data to the storage medium again.
X Remove the storage medium.
Transferring data to another system
(vehicle) X
Insert/connect the storage medium (SD
card

or USB stick) with the saved data into/
to the relevant interface.
X Select Vehicle
in the main function bar by
turning cVd the COMAND controller and
press W to confirm.
The "Vehicle" menu appears.
X Select System and press W to confirm.
X Select Upload/Download Data and press
W to confirm.
X Select Import Data from Storage
Medium and press W to confirm.
X Select Start Data Import.
A prompt appears, asking whether the
COMAND data should be overwritten.
X Press Yes
to confirm that the data saved in
COMAND should be overwritten.
COMAND imports the data and restarts the
system.
or
X Press No to cancel the import process. Vehicle
273
COMAND Z

display
= next to the symbol for the change
of direction ;. This decreases in size as you
approach the announced change of direction.
Change of direction announced with a
lane recommendation
Lane recommendations are only displayed if
the relevant data is available on the digital
map. :
Road into which the change of direction
leads
; Symbol for change of direction
= Distance to change of direction and visual
distance display
? Lane recommendation
On multiple-lane roads, COMAND can provide
lane
recommendation ? for the next change
of direction. Lanes may be added during a
change of direction. :
Uninterrupted lane
; New lane during a change of direction
= Lane recommended for the change of
direction Other status indicators of the
navigation system R
O : you have reached the destination or
an intermediate destination.
R New

route......: COMAND is calculating
the new route.
R Direction of Dest. Off map or
Direction of Dest. Off mapped road :
the vehicle position is outside the area of
the digital map (off-map position).
R Direction of Dest. No Route : no route
could be calculated to the selected
destination. Audio menu
Selecting a radio station i
SIRIUS XM satellite radio acts like a
normal radio.
For more information on satellite radio
operation, see the separate operating
instructions.
X Switch on COMAND and select Radio
(Y page 211).
X Press the = or ; button on the
steering wheel to select the Audio menu. :
Memory slot (only if the station is stored)
; Station
= Waveband378
Menus and submenus
On-board computer and displays

X
Press and hold Roadside Assistance
button : for more than two seconds.
This initiates a call to the Mercedes-Benz
Customer
Assistance Center. The indicator
lamp in Roadside Assistance button :
flashes while the call is active. The
Connecting Call message appears in the
multifunction display and the COMAND
display. The audio output is muted.
If a connection can be established, the Call
Connected message appears in the
multifunction display and in the COMAND
display.
If a cellular phone network is available and
there

is sufficient GPS reception, the mbrace
system transmits data to the Mercedes-Benz
Customer Assistance Center, for example:
R current location of the vehicle
R vehicle identification number
i The multifunction display and COMAND
display show that an mbrace call is active.
You can change to the navigation menu by
pressing the S button during the call,
for example.
Voice output is not available.
A voice connection is established between
the Mercedes-Benz Customer Assistance
Center and the vehicle occupants.
X Describe the type of assistance needed.
The Mercedes-Benz Customer Assistance
Center either sends a qualified Mercedes-
Benz

technician or organizes for your vehicle
to be transported to the nearest authorized
Mercedes-Benz Center. You may be charged for services such as repair work and/or
towing. Further details are available in your
mbrace manual.
i
The mbrace system failed to initiate a
Roadside Assistance call if:
R the indicator lamp in Roadside
Assistance button : is flashing
continuously.
R no voice connection to the Mercedes-
Benz Customer Assistance Center was
established.
This may be because the corresponding
mobile phone network is not available.
The Call Failed message appears in the
multifunction display.
The COMAND display shows the Call
could not be connected! message.
Press W to confirm the message.
X To end a call:
press the ~ button on the
multifunction steering wheel.
or
X Press the corresponding button for ending
a phone call on the COMAND telephone
keypad.
MB Info call button X
Open the stowage compartment under the
armrest (Y page 433). X
Press and hold MB Info call button : for
more than two seconds.
This initiates a call to the Mercedes-Benz
Customer

Assistance Center. The indicator
lamp in MB Info call button : flashes while446
Features
Stowing and features

the connection is being established. The
Connecting
Call message appears in the
multifunction display. The COMAND
display shows the Information Call
Activated message. The audio output is
muted.
If a connection can be established, the Call
Connected message appears in the
multifunction display.
The COMAND display shows the
Information Call Activated message.
If a cellular phone network is available and
there

is sufficient GPS reception, the mbrace
system transmits data to the Mercedes-Benz
Customer Assistance Center, for example:
R current location of the vehicle
R vehicle identification number
i The COMAND display shows that an
mbrace call is active. You can change to the
navigation menu by pressing the S
button during the call, for example.
Voice output is not available.
A voice connection is established between
the Mercedes-Benz Customer Assistance
Center and the vehicle occupants. You can
obtain information on how to operate your
vehicle's systems, on the location of the
nearest authorized Mercedes-Benz Center,
and on further products and services offered
by Mercedes-Benz USA.
Further details on the mbrace system can be
found under http://www.mbusa.com 25
.
Log in under "Owners Online".
i The mbrace system failed to initiate an
MB Info call if:
R the indicator lamp in MB Info call
button : is flashing continuously.
R no voice connection to the Mercedes-
Benz Customer Assistance Center was
established.
This may be because the corresponding
mobile phone network is not available. The
Call Failed message appears in the
multifunction display.
The COMAND display shows the Call
could not be connected! message.
Press W to confirm the message.
X To end a call: press the ~ button on the
multifunction steering wheel.
or
X Press the corresponding button for ending
a phone call on the COMAND telephone
keypad.
Call priority When service calls are active, e.g. Roadside
Assistance or MB Info calls, an emergency
call can still be initiated. In this case, an
emergency

call will take priority and override
all other active calls.
The indicator lamp of the respective button
flashes until the call is ended. An emergency
call can only be terminated by the Mercedes-
Benz Customer Assistance Center. All other
calls can be ended by pressing the ~
button on the multifunction steering wheel or
the corresponding button for ending a
telephone call on the COMAND telephone
keypad.
Downloading destinations in COMAND i
The
components and operating principles
of COMAND can be found on
(Y page 118).
i You can only use the Destination
Download function if the vehicle is
equipped with a navigation system.
Destination Download gives you access to a
database with over 15 million points of
interest (POIs)/important destinations that
can be downloaded onto the navigation
system of your vehicle. If you know the
destination, you can download the address or
obtain the location of points of interest
25 USA only. Features
447
Stowing and features Z

(POIs)/important destinations in the
surrounding area.
You are prompted to confirm route guidance
to the address entered.
X
Slide XVY and turn cVd the COMAND
controller to select Yes and confirm by
pressing W.
The system calculates the route and
subsequently starts the route guidance with
the address entered.
i If
you select No, the address can be stored
in the address book.
i The Destination Download function is
available if the corresponding mobile
phone network is available and data
transfer is possible.
Route Assistance
This service is part of the mbrace PLUS
Package and cannot be purchased
separately.
i You can also use the Route Assistance
function if your vehicle is not equipped with
a navigation system.
Within the framework of this service, you
receive a professional and reliable form of
navigation support without having to leave
your vehicle.
The customer service representative
determines a suitable driving route based on
your current vehicle position and the desired
destination and guides you live through the
current sections of the route.
Search & Send Points to observe before use
i
To use Search & Send, your vehicle must
be equipped with mbrace and a navigation
system. You must also have an mbrace
service subscription.
"Search & Send" is a destination entry
service.

A destination which is determined by
Google Maps ®
or Yahoo Local Maps ®
can be forwarded directly to your vehicle's
navigation system using TELEAID.
Specifying and sending the destination
address
i
Information about specific commands
such as address entry or sending an
address can be found on (either of) the
website(s). Each website works differently
and is subject to change.
X Go to either http://
www.maps.google.com or http://
www.maps.yahoo.com

and enter a
destination address in the entry field.
X Press the relevant button on the website to
send the destination address to the e-mail
address of your mbrace account.
X When the "Send" dialog window appears:
In the relevant field, enter the e-mail
address which you specified when
activating your mbrace account.
X Click on "Send".
Calling up destination addresses
X Press the MB Info call button to load the
destination address to your vehicle's
navigation system.
A display message appears, asking
whether navigation should be started.
X Slide XVY and turn cVd the COMAND
controller to select Yes and confirm by
pressing W.
The system calculates the route and
subsequently starts the route guidance
with the address entered.
i If
you select No, the address can be stored
in the address book.
i If you have sent more than one
destination address, you have to make an
info call to load each individual address.
i Destination addresses are loaded in the
same order as the order in which they were
sent. If you own multiple Mercedes-Benz
vehicles with mbrace and activated mbrace
accounts: 448
Features
Stowing and features