Page 196 of 688

1964-2. Driving procedures
CT200h_OM_OM76102E_(EE)
Power (ignition) switch
Check that the parking brake is set.
Firmly depress the brake pedal.
Check that the power switch indicator turns green. If the indicator does not
turn green, the hybrid system cannot be started.
When the shift position is N, the hybrid system cannot start. Shift the shift
position to P when starting the hybrid system. (P. 205)
Press the power switch.
Continue depressing the brake pedal
until the hybrid system is completely
started.
The hybrid system can be started
from any power switch mode.
Check that the “READY” indicator is illuminated.
If the “READY” indicator changes from a flashing light to a solid light and
the buzzer sounds, the hybrid system is starting normally.
The vehicle will not move when the “READY” indicator is off.
The vehicle can move when the “READY” indicator is on even if the engine
is stopped. (The gasoline engine starts or stops automatically in accordance
with the state of the vehicle.)
Performing the following operations when carrying the electronic key on
your person starts the hybrid system or changes power switch modes.
Starting the hybrid system
1
2
3
4
Page 200 of 688

2004-2. Driving procedures
CT200h_OM_OM76102E_(EE)
WA R N I N G
When starting the hybrid system
Always start the hybrid system while sitting in the driver’s seat. Do not depress
the accelerator pedal while starting the hybrid system under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
Stopping the hybrid system in an emergency
If you want to stop the hybrid system in an emergency while driving the vehi-
cle, press and hold the power switch for more than 2 seconds, or press it briefly
3 times or more in succession. (P. 561)
However, do not touch the power switch while driving except in an emergency.
Turning the hybrid system off while driving will not cause loss of steering or
braking control, however, power assist to the steering will be lost. This will
make it more difficult to steer smoothly, so you should pull over and stop the
vehicle as soon as it is safe to do so.
NOTICE
To prevent 12-volt battery discharge
Do not leave the power switch in ACCESSORY or ON mode for long periods
of time without the hybrid system on.
If the hybrid system is off, but the indicator on the power switch is illumi-
nated, this indicates that the power switch is still turned on. When exiting the
vehicle, always check that the power switch is off.
When starting the hybrid system
If the hybrid system becomes difficult to start, have your vehicle checked by
any authorized Lexus dealer or repairer, or another duly qualified and equipped
professional immediately.
Symptoms indicating a malfunction with the power switch
If the power switch seems to be operating somewhat differently than usual,
such as the switch sticking slightly, there may be a malfunction. Contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional immediately.
Page 206 of 688

2064-2. Driving procedures
CT200h_OM_OM76102E_(EE)
For the shift positions
When the power switch is off, the shift position cannot be changed.
When the power switch is in ON mode (the hybrid system is not operating), the
shift position can only be changed to N. The shift position will be changed to N
even if the shift lever is shifted to D or R and held in that position.
When the “READY” indicator is on, the shift position can be changed from P to
D, N or R.
When the “READY” indicator is flashing, the shift position cannot be changed
from P to another position even if the shift lever is operated. Wait until the
“READY” indicator changes from a flashing to a solid light, and then operate
the shift lever again.
The shift position can only be changed to B directly from D.
In addition, if an attempt is made to change the shift position by moving the shift
lever or by pressing the P position switch in any of the following situations, the
buzzer will sound and the shifting operation will be disabled or the shift position
will automatically change to N. When this happens, select an appropriate shift
position.
Situations where the shifting operation will be disabled:
• When an attempt is made to change the shift position from P to another posi-
tion by moving the shift lever without depressing the brake pedal.
• When an attempt is made to change the shift position from P or N to B by
moving the shift lever.
Situations where the shift position will automatically change to N:
• When the P position switch is pressed while the vehicle is running.
*1
• When an attempt is made to select the R position by moving the shift lever
when the vehicle is moving forward.
*2
• When an attempt is made to select the D position by moving the shift lever
when the vehicle is moving in reverse.
*3
• When an attempt is made to change the shift position from R to B by moving
the shift lever.
*1: Shift position may be changed to P when driving at extremely low speeds.
*2: Shift position may be changed to R when driving at low speeds.
*3: Shift position may be changed to D when driving at low speeds.
Reverse warning buzzer
When shifting into R, a buzzer will sound to inform the driver that the shift posi-
tion is in R.
Page 209 of 688
209
4 4-2. Driving procedures
Driving
CT200h_OM_OM76102E_(EE)
Turn signal lever
Right turn
Lane change to the right (push
and hold the lever partway)
The right hand signals will flash
until you release the lever.
Lane change to the left (push and
hold the lever partway)
The left hand signals will flash until
you release the lever.
Left turn
Turn signals can be operated when
The power switch is in ON mode.
If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned out.
Operating instructions
1
2
3
4
Page 211 of 688
211
4 4-3. Operating the lights and wipers
Driving
CT200h_OM_OM76102E_(EE)
Headlight switch
Turning the end of the lever turns on the lights as follows:
The daytime running
lights turn on.
The front position, tail,
license plate and instru-
ment panel lights turn on.
The headlights and all
lights listed above turn
on.
The headlights, daytime
running lights and front
position lights turn on
and off automatically.
(When the power switch
is in ON mode.)
The headlights can be operated manually or automatically.
Operating instructions
1
2
3
4
Page 212 of 688
2124-3. Operating the lights and wipers
CT200h_OM_OM76102E_(EE)
With the headlights on, push the
lever away from you to turn on
the high beams.
Pull the lever toward you to the cen-
ter position to turn the high beams
off.
Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with
the headlights on or off.
This system allows the headlights to be turned on for 30 seconds when
the power switch is off.
Pull the lever toward you and
release it with the light switch is in
or after turning the power
switch off.
Pull the lever toward you and release
it again to turn off the lights.
Turning on the high beam headlights
1
2
Follow me home system
Page 213 of 688
2134-3. Operating the lights and wipers
4
Driving
CT200h_OM_OM76102E_(EE)
The level of the headlights can be adjusted according to the number of
passengers and the loading condition of the vehicle.
Raises the level of the headlights
Lowers the level of the head-
lights
Guide to dial settings
Manual headlight leveling dial (if equipped)
1
2
Occupancy and luggage load conditionsDial positionOccupantsLuggage load
DriverNone0
Driver and front
passengerNone0
All seats occupiedNone1.5
All seats occupiedFull luggage loading2.5
DriverFull luggage loading4
Page 214 of 688

2144-3. Operating the lights and wipers
CT200h_OM_OM76102E_(EE)
Daytime running light system
To make your vehicle more visible to other drivers, the front position lights turn
on automatically (at an increased intensity) whenever the hybrid system is started
and the parking brake is released. Daytime running lights are not designed for
use at night.
Headlight control sensor
Automatic light off system
When the light switch is in the or position: The headlights turn off
automatically if the power switch is turned to ACCESSORY mode or OFF.
When the light switch is in the position: The headlights and all lights turn
off automatically if the power switch is turned to ACCESSORY mode or OFF.
To turn the lights on again, turn the power switch to ON mode, or turn the light
switch off once and then back to the
or position.
Automatic headlight leveling system (if equipped)
The level of the headlights is automatically adjusted according to the number of
passengers and the loading condition of the vehicle to ensure that the headlights
do not interfere with other road users.
Light reminder buzzer (if equipped)
A buzzer sounds when the power switch is turned off or turned to ACCESSORY
mode and the driver’s door is opened while the lights are turned on. The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.