2013 Lexus CT200h display

1072. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76102E_(EE)
The meters and display illuminate when
The power switch is in ON mode.
Hybrid System Indicator
Hybrid System Indicator is displayed when the driving mode is in other than the
sport mode.
By keeping the indicator needle within Eco area, more Eco-friendly driving can
be achieved.
Charge area indicates regeneration* status. Regenerated energy will be used to
charge the hybrid battery (traction battery).
*: When used in this manual, “regeneration” refers to the conversion of energy
created by the movement of the vehicle into electrical energy.
Tachometer (if equipped)
The tachometer is displayed when the driving mode is in the sport mode.
ECO lamp and SPORT lamp (if equipped)
When sport mode is selected, the SPORT lamp (red) will illuminate.
When all of the following conditions are satisfied and the Eco-friendly driving,
the ECO lamp (blue) will illuminate:
• Driving with the shift position in D
• Either normal mode or Eco drive mode is selected, and EV drive mode is not
in use (P. 201, 265)
• The vehicle speed is approximately 130 km/h (80 mph) or below. Power area
Shows that an Eco-friendly driving range
is being exceeded (during full power
driving etc.)
Eco area
Shows that the vehicle is being driven in
an Eco-friendly manner.
Hybrid Eco area
Shows that gasoline engine power is not
being used very often.
The gasoline engine will automatically
stop and restart under various conditions.
Charge area
Shows that energy is being recovered via
the regenerative brake.
1
2
3
4

1082. Instrument cluster
CT200h_OM_OM76102E_(EE)
Engine speed
On hybrid vehicles, engine speed is precisely controlled in order to help improve
fuel efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even when
vehicle operation and driving conditions are the same.
Outside temperature display
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/exit of
a garage, tunnel, etc.)
When “--” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional.
Customization
Settings (e.g. on/off operation of the ECO lamp) can be changed.
(Customizable features: P. 650)
NOTICE
To prevent damage to the engine and its components
Vehicles with tachometer: Do not let the indicator needle of the tachometer
enter the red zone, which indicates the maximum engine speed.
The engine may be overheating if the high coolant temperature warning light
comes on or flashes. In this case, immediately stop the vehicle in a safe place,
and check the engine after it has cooled completely. (P. 628)

109
2 2. Instrument cluster
Instrument cluster
CT200h_OM_OM76102E_(EE)
Multi-information display (with monochrome
display)

The multi-information display presents the driver with a variety of vehi-
cle data.
Energy monitor
Displays the status of the hybrid sys-
tem. (P. 117)
Drive information
Displays driving range, fuel con-
sumption and other cruising related
information. (P. 1 1 0 )
Setting
Changes instrument cluster display
settings (P. 650)
Lexus parking assist-sensor (if equipped)
Automatically displayed when the system is used (P. 245)
Dynamic radar cruise control display (if equipped)
Automatically displayed when the system is used (P. 231)
Warning messages
Automatically displayed when a malfunction occurs in one of the vehicle’s
systems (P. 575)
: If equipped
Display contents

1102. Instrument cluster
CT200h_OM_OM76102E_(EE)
Items displayed can be switched by
pressing the “DISP” switch.
Energy monitor
P. 1 1 7
Current fuel consumption/Average fuel consumption after refueling
Displays the instant fuel consumption and average fuel consumption
after refueling.
Use the displayed average fuel consumption as a reference.
Average fuel consumption
Displays the average fuel consumption since the function was reset.
• The function can be reset by pressing the “DISP” switch for longer than 1
second when the average fuel consumption is displayed.
• Use the displayed average fuel consumption as a reference.
Cruising range
Displays the estimated maximum distance that can be driven with the
quantity of fuel remaining.
• This distance is computed based on your average fuel consumption.
As a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may not
be updated.
When refueling, turn the power switch off. If the vehicle is refueled with-
out turning the power switch off, the display may not be updated.
Elapsed time
Displays the elapsed time since the hybrid system was started or the
function was reset.
The function can be reset by pressing the “DISP” switch for longer than 1
second when the elapsed time is displayed.
Average vehicle speed
Displays the average vehicle speed since the function was reset.
Drive information

1112. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76102E_(EE)The function can be reset by pushing the “DISP” switch for longer than 1
second when the average vehicle speed is displayed.
Setting
P. 6 5 0
Display off
A blank screen is displayed
System check display
After turning the power switch to ON mode, opening image is displayed while
system operation is checked. When the system check is complete, the normal
screen will return.
When disconnecting and reconnecting 12-volt battery terminals
The drive information will be reset.
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is charac-
teristic of liquid crystal displays, and there is no problem continuing to use the
display.
NOTICE
The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.

1122. Instrument cluster
CT200h_OM_OM76102E_(EE)
Multi-information display (with color display)
The multi-information display presents the driver with a variety of vehi-
cle data.
Menu icons
Displays the following informa-
tion when an icon is selected.
(P. 1 1 4 )
Some of the information may be
displayed automatically depend-
ing on the situation.
Drive information
Select to display various drive data. (P. 1 1 5 )
Navigation system-linked display (if equipped)
Select to display the following navigation system-linked information.
• Route guidance
• Compass display (north-up display/heading-up display)
Audio system-linked display (if equipped)
Select to enable selection of an audio source or track on the display
using the meter control switches.
Select to display the cruise control/dynamic radar cruise control infor-
mation, when the system is used. (P. 228, 231)
The displayed icon changes depending on the system used.
Warning message display
Select to display warning messages and measures to be taken if a mal-
function is detected. (P. 575)
Settings display
: If equipped
Display contents
Cruise control/Dynamic radar cruise control display (if
equipped)

1132. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76102E_(EE)Select to change the meter display settings. (P. 650)

1142. Instrument cluster
CT200h_OM_OM76102E_(EE)
Energy monitor
Displays the status of the hybrid system.(P. 1 1 7 )
Lexus parking assist-sensor (if equipped)
Automatically displayed when the system is used (P. 245)
The multi-information display is
operated using the meter control
switches.
Select an item/change pages
Enter/Set
Return to the previous screen
Press:
Displays the screen registered to
When no screen has been registered, the drive information screen will be dis-
played.
Press and hold:
Registers the currently displayed screen to (P. 650)
The registration confirmation screen is displayed. If the selected screen cannot
be registered, a registration failure message will be shown.
Operating the meter control switches
1
2
3
4