2013 Lancia Voyager tow

 This device must accept any inter-ference received, including interfer-
ence that may cause undesired op-
eration.
If your RKE transmitter fails to oper-
ate from a normal distance, check for
these two conditions.
1. A weak battery in the RKE trans-
mitter. The expected life of the battery
is a minimum of three years.
2. Closeness to a radio transmitter
such as a radio station tower, airport
transmitter, and some mobile or CB
radios.
DOOR LOCKS
MANUAL DOOR LOCKS
Lock the front doors by pushing down
on the lock knobs on each door trim
panel.
If the lock knob is down when you
shut either front door, the door will
lock. Make sure the keys are not inside
the vehicle before closing the door. If the lock knob is rearward when you
shut either side sliding door, the door
will lock. Make sure the keys are not
inside the vehicle before closing the
door.
WARNING!
 For personal security and safety
in the event of a collision, lock the
vehicle doors as you drive as well
as when you park and leave the
vehicle.
 When leaving the vehicle, always
remove the Key Fob from the ig-
nition and lock your vehicle.
 Never leave children alone in a vehicle, or with access to an un-
locked vehicle.
 Allowing children to be in a ve- hicle unattended is dangerous for
a number of reasons. A child or
others could be seriously or fa-
tally injured. Children should be
warned not to touch the parking
brake, brake pedal or the shift
lever.
 Do not leave the Key Fob in or near the vehicle, or in a location
accessible to children, and do not
leave Keyless Enter­N­Go™ in
the ACC or ON/RUN mode. A
child could operate power win-
dows, other controls, or move the
vehicle.
Manual Door LockSliding Door Lock
21

2. Slide the Child Protection Door
Lock control inward (toward the ve-
hicle) to engage the Child Protection
Door Lock.
3. Repeat Steps 1 and 2 on the oppo-
site sliding door.
NOTE:
 After engaging the Child Protec-tion Door Lock, always test the
door from the inside to make
certain it is in the desired posi-
tion.
 When the Child Protection Door Lock system is engaged, (even if
the inside door lock is in the
unlocked position) the door can
be opened only by using the out-
side door handle, the RKE
transmitter, the switches on the overhead console or the switches
located on the trim panel just in
front of the power sliding door.
 The power sliding side door will operate from the switches lo-
cated on the b-pillar trim panel,
just in front of the power sliding
door, regardless of the Child
Protection Door Lock lever po-
sition. To avoid unintentional
operation of the power sliding
door from the rear seats, press
the “OFF” Master Lock Out
Switch located in the front over-
head console, next to the driver.
WARNING!
Avoid trapping anyone in the ve-
hicle in a collision. Remember that
the sliding doors can only be
opened from the outside door
handle or the switches located on
the trim panel just in front of the
power sliding door when the Child
Protection Door Locks are engaged.
To Disengage the Child Protection
Door Lock
1. Open the sliding side door. 2. Slide the Child Protection Door
Lock control outward (away from the
vehicle) to disengage the Child Pro-
tection Door Lock.
3. Repeat Steps 1 and 2 on the oppo-
site sliding door (for versions/
markets, where provided).
NOTE:
 After setting the Child Protec-
tion Door Lock system, always
test the door from the inside to
make certain it is in the desired
position.
 The power sliding side door switches will not open the power
sliding doors if the vehicle is in
gear or the vehicle speed is
above 0 km/h.
 The power sliding door will op- erate from the outside door
handle, the RKE transmitter, the
switches on the overhead con-
sole, or the switches located on
the trim panel just in front of the
power sliding door when the
shift lever is in PARK, regardless
of the child lock lever position.
Child Protection Door Lock
31

5. Position the shoulder belt on your
chest so that it is comfortable and not
resting on your neck. The retractor
will withdraw any slack in the belt.
6. To release the belt, push the red
button on the buckle. The belt will
automatically retract to its stowed po-
sition. If necessary, slide the latch
plate down the webbing to allow the
belt to retract fully.WARNING!
A frayed or torn belt could rip apart
in a collision and leave you with no
protection. Inspect the belt system
periodically, checking for cuts,
frays, or loose parts. Damaged
parts must be replaced immedi-
ately. Do not disassemble or modify
the system. Seat belt assemblies
must be replaced after a collision if
they have been damaged (bent re-
tractor, torn webbing, etc.).Third Row Center Shoulder Belt
Instructions
The shoulder belt for the third row
center seat is located in the headliner
slightly behind the third row seat.
Pull the strap down and secure the
small latch plate of the lap belt into
the small buckle until you hear a
“click”.
Position the shoulder belt on your
chest so that it is comfortable and not
resting on your neck. When the belt is
long enough to fit , insert the large
latch plate into the buckle until you
hear a “click.” The retractor should
withdraw any slack in the belt.
To release the small latch plate, posi-
tion the end of the large latch plate
against the red button on the small
latch plate and push upward. Rein-
stall the latch plates into the head-
liner. Lap/Shoulder Belt Untwisting
Procedure
Use the following procedure to un-
twist a twisted lap/shoulder belt.
1. Position the latch plate as close as
possible to the anchor point.
2. At about 15 to 30 cm above the
latch plate, grasp and twist the belt
webbing 180 degrees to create a fold
that begins immediately above the
latch plate.
3. Slide the latch plate upward over
the folded webbing. The folded web-
bing must enter the slot at the top of
the latch plate.
4. Continue to slide the latch plate up
until it clears the folded webbing.
37

The BeltAlert® warning sequence be-
gins after the vehicle speed is over
8 km/h, by blinking the Seat Belt
Reminder Light and sounding an in-
termittent chime. Once the sequence
starts, it will continue for the entire
duration or until the respective seat-
belts are fastened. After the sequence
completes, the Seat Belt Reminder
Light remains illuminated until the
respective seat belts are fastened. The
driver should instruct all other occu-
pants to fasten their seat belts. If a
front seat belt is unbuckled while
traveling at speeds greater than
8 km/h, BeltAlert® will provide both
audio and visual notification.
The front passenger seat BeltAlert® is
not active when the front passenger
seat is unoccupied. BeltAlert® may be
triggered when an animal or heavy
object is on the front passenger seat or
when the seat is folded flat (for
versions/markets, where provided). It
is recommended that pets be re-
strained in the rear seat in pet har-
nesses or pet carriers that are secured
by seat belts, and cargo is properly
stowed.BeltAlert® can be enabled or disabled
by your authorized dealer. LANCIA
does not recommend deactivating
BeltAlert®.
NOTE: Although BeltAlert® has
been deactivated, the Seat Belt Re-
minder Light will continue to illu-
minate while the driver’s or front
passenger (for versions/markets,
where provided with BeltAlert®)
seat belt remains unfastened.
SEAT BELTS AND
PREGNANT WOMEN
We recommend that pregnant women
use the seat belts throughout their
pregnancies. Keeping the mother safe
is the best way to keep the baby safe.
Pregnant women should wear the lap
part of the belt across the thighs and
as snug across the hips as possible.
Keep the belt low so that it does not
come across the abdomen. That way
the strong bones of the hips will take
the force if there is a collision.
SUPPLEMENTAL
RESTRAINT SYSTEM (SRS)
— AIR BAGS
This vehicle has Advanced Front Air
Bags for both the driver and front
passenger as a supplement to the seat
belt restraint systems. The driver's
Advanced Front Air Bag is mounted
in the center of the steering wheel.
The passenger's Advanced Front Air
Bag is mounted in the instrument
panel, above the glove compartment.
The words SRS AIRBAG are em-
bossed on the air bag covers.
1 — Driver And
Passenger Ad-
vanced Front Air
Bags
2 — Knee Bol-
sters (for
versions/markets,
where provided)
44

turn the buckle around, and insert
the latch plate into the buckle
again. If you still can't make the
child restraint secure, try a differ-
ent seating position.
 Buckle the child into the seat ac- cording to the child restraint manu-
facturer's directions.WARNING!
When your child restraint is not in
use, secure it in the vehicle with the
seat belt or remove it from the ve-
hicle. Do not leave it loose in the
vehicle. In a sudden stop or colli-
sion, it could strike the occupants
or seatbacks and cause serious per-
sonal injury.
ISOFIX — Child Seat Anchorage
System
Each vehicle, except com-
mercial cargo vehicles, is
equipped with the child re-
straint anchorage system
called ISOFIX. Two ISOFIX child re-
straint anchorage systems are in-
stalled on all second-row seats and in the center position on all third row
fold-in-floor seats. Second-row seats
also feature tether strap anchorages,
located in the rear surface of the seat-
back. In addition, all third row fold-
in-floor seats are equipped with a
child restraint tether anchor at the
center seating position.
NOTE:
 When using the ISOFIX attach-
ing system to install a child re-
straint, please ensure that all
seat belts not being used for oc-
cupant restraints are stowed and
out of reach of children. It is
recommended that before in-
stalling the child restraint,
buckle the seat belt so the seat
belt is tucked behind the child
restraint and out of reach. If the
buckled seat belt interferes with
the child restraint installation,
instead of tucking the seat belt
behind the child restraint, route
the seat belt through the child
restraint belt path and then
buckle it. This should stow the
seat belt out of the reach of an inquisitive child. Remind all
children in the vehicle that the
seat belts are not toys and
should not be played with, and
never leave your child unat-
tended in the vehicle.
 If your child restraint seat is not ISOFIX-compatible, install the
restraint using the vehicle seat
belts.
Installing the Lower Attachments:
1. The vehicle lower anchorages are
round bars located at the rear of the
seat cushion where it meets the seat-
back.
2. Loosen the adjusters on the lower
child restraint attachment straps (ref-
erence the child restraint seat instruc-
tions) to ease the installation.
NOTE: It is recommended to
loosen the top tether strap and
route it loosely prior to securing
the lower anchors so the top tether
strap is not trapped between the
vehicle seat and child restraint.60

WARNING!
An incorrectly anchored tether
strap could lead to increased head
motion and possible injury to the
child. Use only the anchor positions
directly behind the child seat to se-
cure a child restraint top tether
strap.
NOTE: If your child restraint seat
is not ISOFIX-compatible, install
the restraint using the vehicle seat
belts.
Because the lower anchorages are to
be introduced to passenger carrying
vehicles over a period of years, child
restraint systems having attachments
for those anchorages will continue to
have features for installation in ve-
hicles using the lap or lap/shoulder
belt. They will also have tether straps,
and you are urged to take advantage
of all of the available attachments
provided with your child restraint in
any vehicle.
NOTE: When using the ISOFIX
attaching system to install a child
restraint, please ensure that all seat belts not being used for occu-
pant restraints are stowed and out
of reach of children. It is recom-
mended that before installing the
child restraint, buckle the seat belt
so the seat belt is tucked behind
the child restraint and out of
reach. If the buckled seat belt in-
terferes with the child restraint in-
stallation, instead of tucking the
seat belt behind the child re-
straint, route the seat belt through
the child restraint belt path and
then buckle it. This should stow
the seat belt out of the reach of an
inquisitive child. Remind all chil-
dren in the vehicle that the seat
belts are not toys and should not be
played with, and never leave your
child unattended in the vehicle.
Installing The Child Restraint
Using The Vehicle Seat Belts
The seat belts in the passenger seating
positions are equipped with an Auto-
matic Locking Retractor (ALR) to se-
cure a Child Restraint System (CRS).
These types of seat belts are designed
to keep the lap portion of the seat belt
tight around the child restraint so that it is not necessary to use a locking clip.
The ALR will make a ratcheting noise
if you extract the entire belt from the
retractor and then allow the belt to
retract into the retractor. For addi-
tional information on ALR, refer to
“Automatic Locking Mode”. The chart
below defines the seating positions
with an Automatic Locking Retractor
(ALR) or a cinching latch plate.
Driver Cen-
terPas-
senger
First
Row N/A N/A ALR
Second
Row ALR N/A ALR
Third
Row ALR Cinch ALR
 N/A — Not Applicable
 ALR — Automatic Locking Retrac- tor
Installing a Child Restraint with an
ALR:
1. To install a child restraint with
ALR, first, pull enough of the seat belt
webbing from the retractor to route it
62

 MANUAL RECLINING SEATS . . . . . . . . . . . . .109
 HEAD RESTRAINTS . . . . . . . . . . . . . . . . . . . .110
 STOW 'N GO® SEATING . . . . . . . . . . . . . . . . .112
 QUAD SEATS(for versions/markets, where provided) . . . . . .114
 THIRD ROW POWER RECLINE (for versions/markets, where provided) . . . . . .117
 THIRD ROW POWER FOLDING SEAT (for versions/markets, where provided) . . . . . .117
 MANUALLY FOLDING THIRD ROW SEATS (for versions/markets, where provided) . . . . . .118
 PLASTIC GROCERY BAG RETAINER HOOKS. . . . . . . . . . . . . . . . . . . . . .119
 DRIVER MEMORY SEAT (for versions/markets, where provided) . . . . . . . .120
 SETTING MEMORY POSITIONS AND LINKING RKE TRANSMITTER TO MEMORY . . . . . . . . .120
 EASY ENTRY/EXIT SEAT (Available With Memory Seat Only) . . . . . . . . .121
 TO OPEN AND CLOSE THE HOOD . . . . . . . . . . .122
 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
 INTERIOR LIGHTING . . . . . . . . . . . . . . . . . . .123
 PARKING LIGHTS . . . . . . . . . . . . . . . . . . . . . .124
 HEADLIGHTS . . . . . . . . . . . . . . . . . . . . . . . . .124
 AUTOMATIC HEADLIGHTS(for versions/markets, where provided) . . . . . .124
 HEADLIGHTS ON WITH WIPERS (for versions/markets, where provided) . . . . . .124
71

MIRRORS
INSIDE DAY/NIGHT
MIRROR (for versions/
markets, where provided)
A two-point pivot system allows for
horizontal and vertical adjustment of
the mirror. Adjust the mirror to center
on the view through the rear window.
Headlight glare can be reduced by
moving the small control under the
mirror to the night position (toward
the rear of the vehicle). The mirror
should be adjusted while set in the day
position (toward the windshield).AUTOMATIC DIMMING
MIRROR (for versions/
markets, where provided)
This mirror automatically adjusts for
headlight glare from vehicles behind
you. You can turn the feature on or off
by pressing the button at the base of
the mirror. A light to the left of the
button will illuminate to indicate
when the dimming feature is acti-
vated. The sensor to the right of the
button does not illuminate.
NOTE: This feature is disabled
when the vehicle is moving in re-
verse.
CAUTION!
To avoid damage to the mirror dur-
ing cleaning, never spray any
cleaning solution directly onto the
mirror. Apply the solution onto a
clean cloth and wipe the mirror
clean.
OUTSIDE MIRRORS
To receive maximum benefit, adjust
the outside mirror(s) to center on the
adjacent lane of traffic with a slight
overlap of the view obtained on the
inside mirror.WARNING!
Vehicles and other objects seen in
an outside convex mirror will look
smaller and farther away than they
really are. Relying too much on side
convex mirrors could cause you to
collide with another vehicle or
other object. Use your inside mirror
when judging the size or distance of
a vehicle seen in a side convex mir-
ror.
Manual Rearview Mirror
Automatic Dimming Mirror
77