Page 73 of 108
AUTOMATIC TRANSMISSION OVERHEATING
• During sustained high speed driving or trailer towing up long grades on hot days,the automatic transmission oil may become too hot.
• When the transmission overheat warning light
turns on, you will experience
reduced performance until the automatic transmission cools down. Once the
transmission has cooled down and the light turns off, you may continue to drive
normally. If the high speed is maintained, the overheating will continue to occur.
• If the overheating continues, it may become necessary to stop the vehicle and run the engine at idle with the transmission in NEUTRAL until the light turns off.
JACKING AND TIRE CHANGING
Jack Location
• The jack and jack-handle are stowed under the load floor in the cargo area.
Spare Tire Stowage
• The compact spare tire is stowed un-der the rear load floor in the cargo area.
Spare Tire Removal
• Lift up the load floor cover and removethe hold down.
Preparations For Jacking
1. Park the vehicle on a firm level sur-
face, avoiding ice or slippery areas.
2. Turn on the Hazard Warning flasher.
3. Set the parking brake.
4. Place the shift lever in PARK (automatic transmission) or REVERSE (manual transmission).
5. Turn OFF the ignition.
WHAT TO DO IN EMERGENCIES
71
Page 88 of 108
FLUIDS AND CAPACITIES
ComponentFluid, Lubricant, or Genuine Part Capacities
Engine Coolant–
2.0L, 2.4L Engine We recommend you use MOPAR
®
Antifreeze/Coolant Ten Year/150,000 Mile
Formula OAT (Organic Additive Technology). 7.2 Quarts
(6.8 Liters)
Includes heater and coolant recoverybottle filled to MAX level.
Engine Oil with Filter– 2.0L,2.4L Engine We recommend you use API Certified
SAE 5W-20 engine oil, meeting the
requirements of Chrysler Material Stan- dard MS-6395. Refer to the engine oil filler cap for correct SAE grade. 4.5 Quarts
(4.26 Liters)
Fuel Selection–
2.0L, 2.4L Engine 87 Octane13.6 Gallons
(51.5 Liters)
(Approximate)
Engine Oil Filter–
2.0L, 2.4L Engine We recommend you use MOPAR
®Engine
Oil Filters. —
Spark Plugs– 2.0L, 2.4L Engine We recommend you use MOPAR
®Spark
Plugs (Gap 0.043 in [1.11 mm]) —
Automatic
Transmission (CVT) We recommend you use MOPAR
®
CVTF + 4®Automatic Transmission Fluid.
—
Manual
Transmission We recommend you use MOPAR®ATF+4®
Automatic Transmission Fluid or
equivalent licensed ATF+4®product. —
Rear Drive
Assembly (RDA) We recommend you use MOPAR®Gear &
Axle Lubricant SAE 80W-90 API GL 5. —
Power Transfer Unit (PTU) We recommend you use MOPAR
®Gear &
Axle Lubricant SAE 80W-90 API GL 5. —
Brake Master Cylinder We recommend you use MOPAR
®DOT 3
and SAE J1703 should be used If DOT 3 is not available, then DOT 4 is acceptable. —
Power Steering Reservoir We recommend you use MOPAR
®Power
Steering Fluid +4 or MOPAR®ATF+4®
Automatic Transmission Fluid. —
MAINTAINING YOUR VEHICLE
86
Page 90 of 108
Your authorized dealer will reset the oil change indicator message after completing
the scheduled oil change. If a scheduled oil change is performed by someone other
than your authorized dealer, the message can be reset by referring to the steps
described under “Electronic Vehicle Information Center (EVIC)/Oil Change Re-
quired” in “Understanding Your Instrument Panel” or under “Instrument Cluster
Description/Odometer/Trip Odometer” in “Understanding Your Instrument Panel” for
further information.
NOTE:
Under no circumstances should oil change intervals exceed 10,000 miles
(16,000 km) or twelve months, whichever comes first.
Once A Month Or Before A Long Trip:
• Check engine oil level
• Check windshield washer fluid level
• Check the tire inflation pressures and look for unusual wear or damage
• Check the fluid levels of the coolant reservoir, brake master cylinder, powersteering and fill as needed
• Check function of all interior and exterior lights
Required Maintenance Intervals.
Refer to the maintenance schedules on the following page for the required mainte-
nance intervals.
At Every Oil Change Interval As Indicated By Oil Change Indicator System:
• Change oil and filter
• Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil
indicator system turns on.
• Inspect battery and clean and tighten terminals as required
• Inspect brake pads, shoes, rotors, drums, hoses and park brake
• Inspect engine cooling system protection and hoses
• Inspect exhaust system
• Inspect engine air cleaner if using in dusty or off-road conditions
MAINTAINING YOUR VEHICLE
88